This channel is dedicated to repairing or rebuilding Broken Big Boy Toys. Videos contain real project vehicles and custom builds built by a father and son team including corvettes; mustangs; challengers; kit cars; exotic vehicles; race bikes; street bikes; dirt bikes; quads; and custom made builds.
Пікірлер
Epic event!🔥 nice video thanks for sharing!!👏
I have a 96 with those but i wanted the lip in on the rear and front. Amazon had them for 183$ each
lol, check the horns/connections first.
I love working on old cars. All the computerized garbage of today is for the birds. Too expensive, too time consuming and too frustrating. Give me an old Ford any day.
adjust those carbs ! sounds very bad !!
I know this video was for the tail light but the front flushed turning signal; do you remember where you got it or the link to it. I got speedmatels but the wiring is a bit off
Can I bring my 1999 Yamaha r1 to you for restoration or have it towed
How much this kinda repair cost at the shop?
Literally my exact same color scheme!
You don't necessarily need to remove the bezel around the gauges to remove that cemter trim piece, you can work around it.
Really struggling to get the wiring right! Where do the yellow wires connect? They only go to the power of the blinkers? Or they go with the ground?
My 1988 cbr 1000f also had bad clutch replaced the clutch no bite in lever
Just the tip you should be also using JIS screwdrivers. Japanese motorcycles are all JIS
I just did a 1985 corvette & you don't have to remove the license plate. Just look at where the rubber bumper bolts on between the exhaust pipes. Remove the bolt. Near the pipes look up & see the back of the lights & pull the rubber out just a little & reach the tail light with Ease. I just did the driver side. Both lights on the same side are easy to get to. No bruise or scratch. Your welcome
I had a question, does the apple carplay actually work?
We’re those. chickens! 😂
My 05 kfx700 will smoke u guy's bikes, let's line em up!
I noticed on a shot that your airbox is sitting on top of your air conditioning pipe. Make sure you elevate that off there because it will rub it with through the pipe and cause you a lot of money.
What nerf bars you got
how much cost for cleaning carburetor ?
Thank you for your video sir
nice vette. I came for the porsche but this is a nice, casual resto
What happened to the oil cooler? And why run the bike without one? Also, you are missing some parts that go inside the oil filter housing, there is a spring and washer that go over the oil filter by-pass bolt before the filter goes on, it keeps the filter pressed against the block.
You can still buy new clutch baskets for this model, but they are EXPENSIVE, around 750 USD.
Forward to 16:39. Hint...they never get to the seals.
Hi was thinking about doing the swap had a question do I need to buy a screen and take the old one out and plug the new one in or do I also need harnesses?
did you ever figure this out?
I have an 81 c3 was the first yr for 2 stage paint. 2nd stage is clear coat. Kinda scratching my head I know your 82 has 2 stage paint and you just sanded through the clear coat. Just my 2 cents. Those c3 were hand painted and they all have blemishes just part of the charm. I wouldn’t be sanding on your paint. You can use a scratch compound on your clear coat but as far as I would go.
I guess you don’t know how to paint. I did not cut through the clear coat. Very hard to explain to someone that knows very little.
Anyone know a way to program my own settings into a chip?
How embarrassing. Guys should of deleted the video instead of uploading the argument
You skipped over the entire bleeding part which is why some of us come here. It was basically half the video of you taking the fender off. Not trying to be a dick but just kinda seems like a Waste of a tutorial video. I have the same bike exactly and having issues bleeding master cylinder and don’t see anywhere to do it.
Your neighbors must love you
Do you have a link or a part number for the air filter
Hey boss so I just need the screen , the module and the housing for it ? I’m trying to change my small screen :(
What is the recommended torque?
You can buy the top-of-the-line vehicle and still gonna have a garbage stereo system in it
Did some wires get crossed?
Wtf you took it to a shop.
Those chips don't work. You're going to be limited to what you can do with the TPI. It has good bottom end torque, but at 4,800 the power takes a nose dive big time. An LS swap is the best all for the L98 TPI minus the engine it could be done for around $1,500 the at depends on the performance stage that you want. I'm willing to bet stock vs stock a 4.8 liter LS would out perform the L98. We would talk about the 5.3 liter or the 6.0 liter.
Totally worthless video. You don't say where you got the parts, and don't comment on whether it made any difference. Oh well.
you didn't show how to replace the boot.
Appreciate the help, just did it on my exact same car (22 EcoBoost MT). I don't think my screen has Navigation, but were you able to get Fordpass set up? I can't get FordPass set up, also the clock auto defaults to another time zone - wonder if there's something to do in Forscan or if I need a GPS antenna.
Reading the comments about to do the swap from my understanding the clock time zone is determined by the gps antenna.
This is correct, I would just unplug the antenna in the end since the old one (and when I bought a compatible new one) both would make my GPS location off on google maps or Waze. Disconnect the blue connector from the back of the APIM and you’ll be fine. FordPass never ended up working with the new antenna for me anyway, so the new antenna was pointless apart from auto time set.
How do you fix a short in door lock
Beautiful cars! I have a question if you can clarify it for me, I have a Corvette c4 that I bought recently, I checked it for everything in general, but without dents, I saw the left rear wheel protruding more
what was missing from the pump ?
Nice work guys
Where did you get the computer from?
Enay
@@brokenbigboytoys5391 You mean EBay
Did you need the VIN from the old car for anything? I might order a kit from an older car but don’t know if I can get the VIN. I don’t need Sirius or Ford NAV
No need for vin off other car radio picks up your vin when installed
@@brokenbigboytoys5391 Thanks fellow Chad
Great, I just got my "Project" and had a lot of questions. This helped a lot. Now I have to find the "FUSE BOX" for the next stage.
06:53 😂😂😂 it’s XSE
Whatever happened to the Sterling Kit Car project?