Пікірлер

• 
  @pegwray9728Ай бұрын

  Having trouble with starting my humvee .installed this Camotek works great got the one with key and remote start I am very happy with this purchase.

• 
  @ZACZPAАй бұрын

  I considered a 300 SEF for the KYB suspension coming from only ever riden KTMs, until I saw the horrible air filter location. Look how filthy that airbox is, what a horrible arrangement.

• 
  @andychips6923Ай бұрын

  It’s not that bad… Yamaha I had was iust as difficult and the air filter was up above the tank. I don’t get why people have an obsession with keeping the air box perfectly clean.. same with cleaning the bike after ever ride. Its a dirt bike. Only thing that matters is getting clean air and fuel to the carb.. dirt in the air box is stagnant. Who cares. Anyway, thanks for the comment 👍

• 
  @ZACZPAАй бұрын

  @@andychips6923 It's a dirtbike, I get it, but it's good opportunity to clean and ensure bike is ready for next ride. Sure it's just going to get dirty again, but I assume you wash your ass - it's just going to get dirty again no? And It's not an obsession with a properly designed airbox with access and maintenance in mind. Pop filter out throw on wash plug, 20 minutes later clean bike and fresh filter ready for next event. Also it also puts your battery, ecm, fuses, relays, etc nicely protected under the seat with easy access.

• 
  @andychips6923Ай бұрын

  Ok, I like you now. Comparing washing my ass with an air filter 😂 The main reason I don’t clean that air-box out is because of that battery being under there.. I will admit that. Would of been nice for them to pick a different spot! My buddy down the street just picked up a sherco and is complaining about the airbox design haha

• 
  @ComonSava4 ай бұрын

  That’s the easy part. Getting the bolt screwed in. Is the hard part and I think is what everyone complains about. I’ve been doing this for 10 minutes straight and cannot get that bolt in. This happens almost every time.

• 
  @andychips69234 ай бұрын

  It’s not bad at all.. as long as the cage is centered, the bolt always finds its place.

• 
  @moosegmc714 ай бұрын

  That was a fun section

• 
  @andychips69234 ай бұрын

  For sure the smoothest.. 😂

• 
  @hexhead57324 ай бұрын

  Single track nice 👍

• 
  @moosegmc715 ай бұрын

  Good thing your bike didn't give you any starting drama on the line.

• 
  @andychips69235 ай бұрын

  Kept the engine running and cleaned it out as much as i could this time.. mistake this go around was starting it in neutral

• 
  @SecondHalfofLife6 ай бұрын

  I'm rocking the K8s. Version 1. I got them used for a song in good condition and love them. Lots of protection and very comfortable and POD supports their old products so you can get replacement parts or upgrade over time.

• 
  @Hendy7117 ай бұрын

  Glad I found this. Getting ready to get some Pods. Was going back and forth on the size but after this you are about my size. Going to lock in the XLs.

• 
  @UTBruteForce8 ай бұрын

  Now how to get one? Website is down/non-functional!

• 
  @clarksd20029 ай бұрын

  I got one with the remote button. I wish I got the one that had the key on the box so my truck doesnt leave me someday.

• 
  @moosegmc7110 ай бұрын

  C'mon, you coulda jumped that!

• 
  @moosegmc7110 ай бұрын

  Yeah Bobby!

• 
  @johnnybravo287310 ай бұрын

  This out in Utah?

• 
  @andychips692310 ай бұрын

  Northern AZ

• 
  @johnnybravo287310 ай бұрын

  @@andychips6923 ah. Beautiful country.

• 
  @Roudy_Riggs10 ай бұрын

  Looks like south centeral Utah. Between Salina and Richfield area.

• 
  @johnnybravo287310 ай бұрын

  @@Roudy_Riggs that's exactly what I was thinking. The mountains in the foreground made me really confident.

• 
  @Helo73510 ай бұрын

  I was thinking Utah out near Virgin.

• 
  @JCadle2611 ай бұрын

  Do they require you to send your old box in? Like core

• 
  @andychips692311 ай бұрын

  He doesn’t deal with old boxes.. his is built from scratch. Way beefier than an oem box. I sold my broke oem box on ebay for $100

• 
  @JCadle2611 ай бұрын

  @@andychips6923 what’s the guys name? Cam. ?

• 
  @andychips692311 ай бұрын

  Cam, yes

• 
  @JCadle2610 ай бұрын

  Got one and I love it

• 
  @user-wn4xx6bs7z11 ай бұрын

  I use heavy equipment ignition switches, usually CAT brand. They always last a long time, are built heavy duty and it makes it really easy to find a replacement key if you should lose it. BTW, just FYI, the wires are 11A - B(att), 29A - R(un) and 14A S(tart)

• 
  @moosegmc7111 ай бұрын

  Yeah, looks like the AM General part has way beefier terminals too

• 
  @STrepp4 Жыл бұрын

  Where did you buy them and how much? How do they fit width wise?

• 
  @andychips6923 Жыл бұрын

  Rocky Mountain atvmc is where I’ve always bought mine.. i have narrow feet and they fit me perfect.. so i cant comment on the width too much. I do have friends that wear AStars only because they have wider feet. I think rocky mountain if i remember right will you return apparel for the first time for free if they dont fit

• 
  @STrepp4 Жыл бұрын

  @@andychips6923 Thanks for the prompt reply.

• 
  @MRALEX9870 Жыл бұрын

  how does shifter and brake feel? is sole too thick?

• 
  @andychips6923 Жыл бұрын

  one reason why I prefer the SG-10 over the 12.. better feel of the shifter

• 
  @jondoe4667 Жыл бұрын

  On the rear I only run 2 tires. 1st is the IRC-M5B, And 2nd is the Kenda washougal 2. They are both way cheaper than a Dunlap and I think way better. I just mounted a set of washougal 2's today and this will be my first time trying it on the front as well.

• 
  @andychips6923 Жыл бұрын

  Just got done putting 40 hrs on a set of michelin starcross mediums. Really like these tires but they’re over a $200 for a set now.. ridiculous! Kendas are catching up on price though.. $170 for a set.. times are changing, just means getting more hours out of existing tires 🫣

• 
  @gearhigher2027 Жыл бұрын

  have you compared decibel reading Thx!

• 
  @andychips6923 Жыл бұрын

  I should work on that, but i would say the Fmf has a throatier sound low down but they are just as loud I would say overall

• 
  @jootai Жыл бұрын

  sick thanks for making the video

• 
  @2-Stroke-Smoke2 жыл бұрын

  I LOVED that wash.

• 
  @warrenstemphly57562 жыл бұрын

  Maybe I’m weird, but I find these slide on roots, even when dry. I’m new to dirt bikes, so I’m pretty ignorant on tires, but my bikes stock Pireli Scorpions seemed to track straighter and not slide on roots.

• 
  @andychips69232 жыл бұрын

  Do you mean side to side sliding? Here in the desert i rarely touch roots but interesting comment. What psi do you run?

• 
  @warrenstemphly57562 жыл бұрын

  @@andychips6923 yes, slide to the left or right a few inches until it hits dirt and get traction. I’m at the recommended 15 psi.

• 
  @andychips69232 жыл бұрын

  @@warrenstemphly5756 try going down to 10psi and see how it feels. Im not sure of your weight, bike set up, or whether you’re running HD tubes but i run fast desert and slow enduro stuff and I’ve never had a problem and im at 215 body weight with irc hd tubes. 15 psi is pretty up there

• 
  @warrenstemphly57562 жыл бұрын

  @@andychips6923 basically I’ve just kept it at what the bike manual says, and the dealership that mounted the tires. I rode it today at 12 psi and it’s a huge improvement, thanks for the tip!

• 
  @lifeoutdoors39537 ай бұрын

  It’s because they are way to hard. I have 3 psi in the front and can barley flex it

• 
  @Greg_3832 жыл бұрын

  Just picked up a set of these. I noticed that they make it harder to flex your knee past 90 degrees...like when you are siting on the very front of the seat. I have long legs and have to bend my knee tight in that position. Is this the same for you? Just have to get used to it?

• 
  @andychips69232 жыл бұрын

  It took maybe 2 or so rides before i got used to them but now I wont ride without them. The other day i took the bike down the road and i felt naked without them! The answer to your question on the pressure while folding your leg past 90 degrees.. I haven’t noticed this at all but im standing a lot of the time while riding and if I’m sitting on the front of the seat, its the only time when I have leg up to the forks (extended straight out) entering into a turn. The opposite leg thats on the peg Ive never noticed that bad of a pressure. How tall are you?

• 
  @Greg_3832 жыл бұрын

  @@andychips6923 I'm 6'1". What you described is the same situation that I'm on the front of the seat. Normally I will bring my inside leg back to the peg while exiting the corner and stand back up. I have to use a noticeable amount of effort to pull my leg back to the peg. It's probably normal with braces, but this is my first set. I might try running the strap above the knee a bit less tight.

• 
  @clintonlied2 жыл бұрын

  For Michigan trails, Enduro Engineering recommended the Washugal front and Millville rear.

• 
  @andychips69232 жыл бұрын

  Millvilles are the next set im running in a couple of weeks. Kendas have been near impossible to get over the last year

• 
  @nielboi8082 жыл бұрын

  love this vids, go shercos

• 
  @painsrides36162 жыл бұрын

  I'm healing form a chest injury and decided to upgrade my upper body protection(lesson learned the hard way)... This got me thinking, maybe I better do the smart thing and replace old knee guards with real knee braces. These POD K4's are making to the top of my list, thanks for the review.

• 
  @Armand_Loggenberg2 жыл бұрын

  Thank you for the awesome video, really appreciated. Stay safe Bro!!

• 
  @mustangdean12 жыл бұрын

  I'm seriously thinking about one of these for my 22 beta 300rr do you still like running it ?? I had bought a FMF 2.1 turbinecore it does not fit the bike correctly unless I want to cut up the side panel to fit.

• 
  @andychips69232 жыл бұрын

  I ran it only for one race I did where it was required.. worked great for the 80 miles. I wouldn’t run it for more than a few hours at a time without removing it and cleaning out the mesh screen.. mine was gummed up after the one race

• 
  @mustangdean12 жыл бұрын

  @@andychips6923 Thanks that's kind of what I figured they wouldn't stay clean very long..

• 
  @jimkerr70642 жыл бұрын

  Thanks for the great review. I'm thinking about these for riding my HD Heritage Softail. At 65, I've had multiple knee surgeries, and I am not ready to stop riding, but one mishap would most likely put me out of commission. My left knee is worse than my right, all I have to do is bump it and I see stars. My one pair of leather riding pants should fit these. Have you had any issues with the Pod fitting inside your riding pants? I appreciate any advice. Thanks again.

• 
  @andychips69232 жыл бұрын

  Motocross style pants have a little more room built into them for knee braces.. I’m not sure about street leathers.. you could most likely wear these on the outside of your riding pants if that would be an option?

• 
  @oklahomahank23782 жыл бұрын

  You should check with your doctor and insurance. They might pay for them since you have bad knees, as I do (American football.) The Asterisk carbon ones are about the slimmest. I recommend the Rocky Mountain ATV and moto videos. He is selling braces, of course, but does direct comparisons.

• 
  @chrisvids18203 жыл бұрын

  I have the rear on my 96 KX250 and it's been great. Thinking about putting one on my Yz250 for track riding buy I don't know if it will corner as good? Just my speculation

• 
  @andychips69232 жыл бұрын

  Put 20 hours on these Kendas and I loved them. But because of supply I haven’t even been able find any more to buy. Cornering was great. Loved the dual compound with the rear tire. Think it did help with durability!

• 
  @chrisvids18202 жыл бұрын

  @@andychips6923 durability is amazing on it

• 
  @tomclifford80853 жыл бұрын

  With the pads on the side, they are thicker one side than the other, does the thicker side go towards the knee cup or the back of the leg

• 
  @andychips69233 жыл бұрын

  Nothing pad wise goes on the “anterior” side of the leg.. if that’s what you’re trying to ask. You have the medial side of the knee (inner) and the lateral side of the knee (outer) where either of the pads go.. and they work well. Since this video I’ve lost 40 pounds from a bad get off.. over the bars and I was using the LARGEST pads in the set in this video. So I’m probably going to have to order a size down now of these knee braces 😬

• 
  @cpsystems40923 жыл бұрын

  So you can use these on a motorbike too?

• 
  @andychips69233 жыл бұрын

  Ooo ya

• 
  @joelballard49523 жыл бұрын

  Agreed. People need to ride more

• 
  @izabelbraga43883 жыл бұрын

  you did not show how to put the disc

• 
  @andychips69233 жыл бұрын

  Ya my buddies filming wasn’t the best.. testing his new camera haha Are you talking about the inserts for the hinge? Or the spacers that go against the knee? The hinge inserts just push in.. very easy. And the spacers are just Velcro. They’ve been holding up great so far

• 
  @izabelbraga43883 жыл бұрын

  this quick and pull sistem dont go out easily? sory english is not my native language

• 
  @andychips69233 жыл бұрын

  You’re just fine.. So far they’re holding up great! The upper and lower buckles I don’t have on very tight so there is not a lot of tension on them.. hopefully they do last a few years at least. Pod from what I understand offers rebuild parts to freshen them up

• 
  @walkeryost71353 жыл бұрын

  How does this bike do in AZ? I'm looking at a sherco vs a ktm but haven't ridden either before. Wondering if it does good in fast desert

• 
  @andychips69233 жыл бұрын

  Hey Walker, it does good.. just like any other 300.. if the majority of your riding is going to be fast desert obviously I’d add a stabilizer. I don’t run one but i have my forks dropped in the clamps and it does great.. sorry for the late reply lol