So the sensor you were not sure of is the IAC, Idle Air Controller,
@JustSomeGuy387903 күн бұрын
@@renegolik502 I don’t remember this video all that well but yeah I figured that out later on. Thanks for clearing that up for others.
@road2richz_q2665 күн бұрын
Hey I'm looking for a idler pulley the one below the Ac compressor where can I get one at with the hardware and spacer
@JustSomeGuy387905 күн бұрын
@@road2richz_q266 I would probably go to rock auto or lmc truck for that.
@sixxgunz37743 ай бұрын
I've watched a few videos and I'm surprised my TBI never leaked, when disassembled I didn't have the little itty bitty plastic/screen pieces in the side of my injectors, the nylon washers on my fuel line connector, nor did i have the metal o-rings. To clean my unit I used carb cleaner to get most of the gunk off, and then used boiling hot water and poured it in every orifice, when cleaning out the tube that the pcv hose hooked up to it made getting all that grease come out like butter with a Q-tip.
@JustSomeGuy387903 ай бұрын
Glad it worked out for you!
@jaivigo3 ай бұрын
02:47 That line that is pointing down, is there nothing connected to that line?
@JustSomeGuy387903 ай бұрын
No I figured out that is a weep hole. When the pump goes bad oil will leak out of that
@JosephPullins-ee1fh3 ай бұрын
And thanks for the review 👍
@JosephPullins-ee1fh3 ай бұрын
Don't ever teflon flanged compression fittings, all it does is fill the threads and make it hard to get the fittings tight enough for the metal to metal seal to engage and can actually make 'em leak
@JustSomeGuy387903 ай бұрын
Ok thanks
@timdskibum4 ай бұрын
And that's why I sold all my quads and got dirtbikes
@JustSomeGuy387904 ай бұрын
To each their own. Quads are more entertaining, and enjoyable for me.
@MrGetDough7604 ай бұрын
People who ride quads are usually people who can't ride a dirtbike 😂
@JustSomeGuy387904 ай бұрын
@@MrGetDough760Half the time I have my 400ex on two wheels like a dirtbike.
@franciscojavierfloressilva41974 ай бұрын
Thanks for the viseo. Can you pleas help me? Can you share a copy of the users manual in pdf? I can not get it anuwhere, pleae help
@JustSomeGuy387904 ай бұрын
I don’t know where to get a pdf for one. I don’t even know if they have a pdf. Like I said in my other reply, try to contact the seller you purchased it from, and try to get another manual.
@Michael-the-original5 ай бұрын
Hi, why did the piston sieze like that?
@JustSomeGuy387905 ай бұрын
I don’t really know. I don’t think it ever locked up because we were able to do a compression test on it and it spun over just fine. I’m pretty sure something got in between the piston, and cylinder, and just scored it up. This engine is broken in now though, and it runs great.
@chadjohnson28535 ай бұрын
Umm where did you find that machine ❤❤❤❤.
@JustSomeGuy387905 ай бұрын
Rotting away in a field.
@chadjohnson28535 ай бұрын
@@JustSomeGuy38790 score 💯.
@JustSomeGuy387905 ай бұрын
KZread took down part 2 because I was apparently showing people how to build a gun even though it was just more milling. So no more gun videos.
@ZDONTEVIDS5 ай бұрын
Dump the cloth in first gear and pop a wheelie
@JustSomeGuy387905 ай бұрын
Might shoot some gears through the floor, but ok!
@chadriddle35175 ай бұрын
From your story I’d say that it blew apart the original piston and when they put a new piston and cylinder in they didn’t clean out the carnage!
@JustSomeGuy387905 ай бұрын
That wouldn’t really surprise me. The engine does smoke quite a bit that’s why I think it has the skirt blown off but I don’t know. It still runs just fine though.
@franciscojavierfloressilva41976 ай бұрын
Crear Review. Dobyuo know how to contact a supplier that can share/sell Instrucciones manual?
@JustSomeGuy387906 ай бұрын
I bought mine through amazon I bet you can contact the seller and try to get a replacement manual.
@JB-de5cp6 ай бұрын
I dont like to hear someone broke as hell, love to send you that pump.
@JustSomeGuy387906 ай бұрын
Haha thanks but no thanks!
@ZDONTEVIDS7 ай бұрын
Are you gonna paint the outside of the truck or nah?
@JustSomeGuy387907 ай бұрын
I would like to paint it eventually but I want to do it right. I don’t wanna rattle can it like I did with the grille and other things. I’ve already wet sanded it you can see the difference from one of the older videos.
@ZDONTEVIDS7 ай бұрын
@@JustSomeGuy38790 ok
@Notion657 ай бұрын
I bought this same fuel pump. It looks like the pump piece sticks out further than the original one I had. Does yours look like that too? Also does your push rod stick out a little bit from the hole?
@JustSomeGuy387907 ай бұрын
I can’t really remember I put the pump on a while ago. The pushrod will stick out a little bit if the cam has the lobe pushing on it. The Haynes manual says to roll the engine over till you can push the rod all the way in probably to make the install easier I didn’t but I’ve been running the pump for a long time and it’s fine. From what I remember the pushrod won’t go all the way into the head it should poke out a little even with the cam lobe facing away from the pushrod. Hope that helps if it doesn’t let me know.
@garagemcmatt7 ай бұрын
Can't go wrong with cometic bro........peace!
@JustSomeGuy387907 ай бұрын
Thanks for checking out my channel!
@garagemcmatt7 ай бұрын
@JustSomeGuy38790 yeah bro pretty sure I said I would
@rose-18138 ай бұрын
New video 👌
@aurelia21828 ай бұрын
please learn the tutorial how to make better video. this is boring af
@JustSomeGuy387907 ай бұрын
It’s an older video so it’s not as good but it’s also not supposed to be super entertaining just informative and I realize now that I didn’t do a good job explaining how to replace the pump so if you need help let me know
@buckpotter31849 ай бұрын
❤ Buck Potter KZread channel love the show thumbs up bro
@ShaneBogue10 ай бұрын
Damn you got those lights on house breakers or something
@juliantrevino314811 ай бұрын
What kind of tire did you use after the wheel was restored?
@JustSomeGuy3879011 ай бұрын
An Accelera Mt-01. It was a 235/75/15 which. Is about a 29” tire I really like them though.
@juliantrevino314811 ай бұрын
@@JustSomeGuy38790 nice, thank you!
@justadudedoinstuff914211 ай бұрын
Some people are just jealous they can’t come up with their own ideas 😂😂
@WeAreAllScrewed.11 ай бұрын
I’m gonna screen shoot this and put on my frig, said no one.
@Nclght Жыл бұрын
Great review. I'm debating between this and the yeswelder CUT-55DS. Being new to cutters, not sure how to properly compare them. Ive been leaning towards this herocut but any feedback on comparison would be helpful. Thanks!
@JustSomeGuy38790 Жыл бұрын
I can’t say much on this cutter yet because I haven’t used it very much but so far I’m liking it for 250 bucks it’s pretty good what I’ve cut so far is 3/16 steel but I know it’ll cut thicker metal one thing I didn’t like is that it kept tripping the breaker on 110v dunno if that would happen in a shop or not tho on 220 it works just fine.
@williamdavis7613 Жыл бұрын
That’s smart 👍
@jonathansantiago436 Жыл бұрын
what flames lol
@justadudedoinstuff9142 Жыл бұрын
It called a wobbly extension haha!
@justadudedoinstuff9142 Жыл бұрын
My farts sound better!
@jamilrajpervlogs Жыл бұрын
❤
@jamilrajpervlogs Жыл бұрын
❤
@rose-1813 Жыл бұрын
✈️
@Canal-Rouler Жыл бұрын
do you sell them?
@JustSomeGuy38790 Жыл бұрын
No sorry
@kenkingsflyingmachines2382 Жыл бұрын
Plunk
@The_Wild_Sprits_Tribe Жыл бұрын
20 bucks
@jasleighter01 Жыл бұрын
How much you pay for them tires boy?
@waylundoldroyd7898 Жыл бұрын
😎👍
@carriemathews86082 жыл бұрын
𝓅𝓇o𝓂o𝓈𝓂
@Ken-pd1ez2 жыл бұрын
🌸 pr໐๓໐Ş๓
@justadudedoinstuff91422 жыл бұрын
Sounds turbocharged
@henyr84642 жыл бұрын
Bro at first I thought that was a real airplane lol
Пікірлер
So the sensor you were not sure of is the IAC, Idle Air Controller,
@@renegolik502 I don’t remember this video all that well but yeah I figured that out later on. Thanks for clearing that up for others.
Hey I'm looking for a idler pulley the one below the Ac compressor where can I get one at with the hardware and spacer
@@road2richz_q266 I would probably go to rock auto or lmc truck for that.
I've watched a few videos and I'm surprised my TBI never leaked, when disassembled I didn't have the little itty bitty plastic/screen pieces in the side of my injectors, the nylon washers on my fuel line connector, nor did i have the metal o-rings. To clean my unit I used carb cleaner to get most of the gunk off, and then used boiling hot water and poured it in every orifice, when cleaning out the tube that the pcv hose hooked up to it made getting all that grease come out like butter with a Q-tip.
Glad it worked out for you!
02:47 That line that is pointing down, is there nothing connected to that line?
No I figured out that is a weep hole. When the pump goes bad oil will leak out of that
And thanks for the review 👍
Don't ever teflon flanged compression fittings, all it does is fill the threads and make it hard to get the fittings tight enough for the metal to metal seal to engage and can actually make 'em leak
Ok thanks
And that's why I sold all my quads and got dirtbikes
To each their own. Quads are more entertaining, and enjoyable for me.
People who ride quads are usually people who can't ride a dirtbike 😂
@@MrGetDough760Half the time I have my 400ex on two wheels like a dirtbike.
Thanks for the viseo. Can you pleas help me? Can you share a copy of the users manual in pdf? I can not get it anuwhere, pleae help
I don’t know where to get a pdf for one. I don’t even know if they have a pdf. Like I said in my other reply, try to contact the seller you purchased it from, and try to get another manual.
Hi, why did the piston sieze like that?
I don’t really know. I don’t think it ever locked up because we were able to do a compression test on it and it spun over just fine. I’m pretty sure something got in between the piston, and cylinder, and just scored it up. This engine is broken in now though, and it runs great.
Umm where did you find that machine ❤❤❤❤.
Rotting away in a field.
@@JustSomeGuy38790 score 💯.
KZread took down part 2 because I was apparently showing people how to build a gun even though it was just more milling. So no more gun videos.
Dump the cloth in first gear and pop a wheelie
Might shoot some gears through the floor, but ok!
From your story I’d say that it blew apart the original piston and when they put a new piston and cylinder in they didn’t clean out the carnage!
That wouldn’t really surprise me. The engine does smoke quite a bit that’s why I think it has the skirt blown off but I don’t know. It still runs just fine though.
Crear Review. Dobyuo know how to contact a supplier that can share/sell Instrucciones manual?
I bought mine through amazon I bet you can contact the seller and try to get a replacement manual.
I dont like to hear someone broke as hell, love to send you that pump.
Haha thanks but no thanks!
Are you gonna paint the outside of the truck or nah?
I would like to paint it eventually but I want to do it right. I don’t wanna rattle can it like I did with the grille and other things. I’ve already wet sanded it you can see the difference from one of the older videos.
@@JustSomeGuy38790 ok
I bought this same fuel pump. It looks like the pump piece sticks out further than the original one I had. Does yours look like that too? Also does your push rod stick out a little bit from the hole?
I can’t really remember I put the pump on a while ago. The pushrod will stick out a little bit if the cam has the lobe pushing on it. The Haynes manual says to roll the engine over till you can push the rod all the way in probably to make the install easier I didn’t but I’ve been running the pump for a long time and it’s fine. From what I remember the pushrod won’t go all the way into the head it should poke out a little even with the cam lobe facing away from the pushrod. Hope that helps if it doesn’t let me know.
Can't go wrong with cometic bro........peace!
Thanks for checking out my channel!
@JustSomeGuy38790 yeah bro pretty sure I said I would
New video 👌
please learn the tutorial how to make better video. this is boring af
It’s an older video so it’s not as good but it’s also not supposed to be super entertaining just informative and I realize now that I didn’t do a good job explaining how to replace the pump so if you need help let me know
❤ Buck Potter KZread channel love the show thumbs up bro
Damn you got those lights on house breakers or something
What kind of tire did you use after the wheel was restored?
An Accelera Mt-01. It was a 235/75/15 which. Is about a 29” tire I really like them though.
@@JustSomeGuy38790 nice, thank you!
Some people are just jealous they can’t come up with their own ideas 😂😂
I’m gonna screen shoot this and put on my frig, said no one.
Great review. I'm debating between this and the yeswelder CUT-55DS. Being new to cutters, not sure how to properly compare them. Ive been leaning towards this herocut but any feedback on comparison would be helpful. Thanks!
I can’t say much on this cutter yet because I haven’t used it very much but so far I’m liking it for 250 bucks it’s pretty good what I’ve cut so far is 3/16 steel but I know it’ll cut thicker metal one thing I didn’t like is that it kept tripping the breaker on 110v dunno if that would happen in a shop or not tho on 220 it works just fine.
That’s smart 👍
what flames lol
It called a wobbly extension haha!
My farts sound better!
❤
❤
✈️
do you sell them?
No sorry
Plunk
20 bucks
How much you pay for them tires boy?
😎👍
𝓅𝓇o𝓂o𝓈𝓂
🌸 pr໐๓໐Ş๓
Sounds turbocharged
Bro at first I thought that was a real airplane lol