It is rod slap you will eventually need to build the top end for any future wonderers common problems with them old sportsman's sorry for the let down.
@ethancampbell85387 ай бұрын
Just the timing
@belette0638 ай бұрын
Hello Sir can you tell me what the finaliment problem was? I'm in the same situation as you friendly
@bradenkylegreen10 ай бұрын
My 07 450 does that sound but only for a little bit after I start it and it just quits
@nathanboutin11 ай бұрын
About to do my first event through scda with my LGT wagon, any tips/major improvement I could make? Your EWG sounded sick too
@modshop182811 ай бұрын
So many things. Lol. Tires, suspension, BRAKES, better bushings and mounts. Also, be careful with the revs and watch your fuel usage. I ended up having a lean miss Because I ran out of fuel and combined with the heavy g-forces in the corners, Pretty sure I ran low or had a misahap with oil starvation and ended up throwing a rod bearing.
@nathanboutin11 ай бұрын
@@modshop1828 tank and jerry cans will be full!! I’m just finishing up with full Whiteline bushing/arms and tein coils w/ falken rt615k+ tires. I’m at 400whp on a iag stage 1. I’ve looked into the killer b baffle/pan/pickup but haven’t pulled the trigger yet
@dtruth5769 Жыл бұрын
Flux Capacitor
@jaywinters2483 Жыл бұрын
its coming from the crank area. It's the balancer shaft. THey put junk bearings in the balancer shaft. You'd have to split the case and rebuild the whole damn thing. Just go with a Honda.
@FrZnPredator10 ай бұрын
Fuck a honda every one we've had was nothing but junk always broken down
@MrSergeAStorms Жыл бұрын
Sounds like the clutch to me. Maybe the hootinator valve? Could try doing a laser sweep on the crystal diodes? How many gigawatts of power is the flux capacitor getting? Should be 1.21
@pattywaktdiy4175 Жыл бұрын
Ha ha, you're just kidding. It's clearly the balance actuators on the rotary girders divided by the rotational spacer weights on the automatic clutch shaft.
@mercurym-7904 Жыл бұрын
That’s the exact sound that my 2002 magnum makes. 😔
@brianbalazs2872 Жыл бұрын
yeah the engine is gonna blow up soon it's a race going out and it blows thecasting out
@robertjamesbreshears8162 Жыл бұрын
Check the bendex that engages flywheel.
@modshop1828 Жыл бұрын
I did. I even ran it with the starter out. I ended up selling it but I believe it was the balance shaft.
@brianatkinson24942 жыл бұрын
My starter bendix gear only knocks under acceleration. Has been doing it since 1,200 miles. I now have 2,000 and nit any worse.
@norain312 жыл бұрын
i acually think 1 of the cam shaft lobes is worn down and making the dull tick . it is a very common problem for 500 sportsman .
@tavaresallen17882 жыл бұрын
It's ur starter bro check ur starter or carnk case
@robertwalker22253 жыл бұрын
She’s done
@clintagar373 жыл бұрын
Did you find out what it was
@justinmainville88743 жыл бұрын
My starter Bendix makes a noice just like that but for only 2 or so seconds when just starting my atv
@ulisesjaramillo9019 Жыл бұрын
Mine does to did you ever fix the problem
@yourownambition24503 жыл бұрын
What was it?
@modshop18283 жыл бұрын
A bearing in the bottom end. I just sent it down the road.
@kayleesmart20842 жыл бұрын
@@modshop1828 is it an expensive fix?
@TheJdubb2353 жыл бұрын
Some say its the valves chattering
@TitaniummanGarage3 жыл бұрын
Did you try and adjust the rockers? The cam wears and the rockers need adjustment after a while.
@IamThatGuy1874 жыл бұрын
Hello, Did you find the fix? Mine is doing the same thing.
@honda400ex64 жыл бұрын
thatguydestroyedyou it is the bendix just replace mine easy fix
@IamThatGuy1874 жыл бұрын
Great thanks, sold the bike lol. Made the buyer aware
@kayleesmart20842 жыл бұрын
@@honda400ex6 it's NOT the bendix. I replaced my bendix, BOTH buschings AND the bendix washer. And it STILL knocks. I have an 06 500 ho
@mattpolack4781 Жыл бұрын
Ever figure out what the problem was with yours I swapped everything out too same rattle
@johnkelley99496 ай бұрын
It is rod slap for any future wonderers it will eventually need a new top end build sorry for the news.
@crystaljohnston98105 жыл бұрын
What was it?
@fixortow3 жыл бұрын
Did he ever answer?
@RICHIE_RICH895 жыл бұрын
Timing chain tensioner
@NotJustAnotherCody5 жыл бұрын
the bike im working on does the same thing but it goes away after a bit
@rcmen26375 жыл бұрын
Primary or secondary clutch.
@kaerlkolderman31765 жыл бұрын
I think it's the starter Bendix gear
@davidlorenz88256 жыл бұрын
starter bendix $30.00 cheep fix
@madmole566 жыл бұрын
Sounds like a bad rod or main bearing.
@NotJustAnotherCody5 жыл бұрын
the bike im working on does the same thing but it goes away after a bit
@JesusRuiz-wn7yx6 жыл бұрын
What heatshields do you have by your right side where the exhaust pipe goes thru to prevent overheat
@justincrediblecountryboy69963 жыл бұрын
I had same exact noise and it was heat shield to lol.
@nathanjohnson63476 жыл бұрын
Starter bendix
@1bananahands6 жыл бұрын
NATHAN JOHNSON , good idea but I took it out and ran it and had the same noise. It's gone now... sold it.
@Heathernjames69696 жыл бұрын
It has a bad connecting rod bearing
@NotJustAnotherCody5 жыл бұрын
the bike im working on does the same thing but it goes away after a bit
@pattywaktdiy4175 Жыл бұрын
If that's the case, replace it now while it's only a top-end disassembly. Quick job in under an hour.
@bryanmiller93247 ай бұрын
@@pattywaktdiy4175To late now. Now the crank is damaged and it needs replaced. Changing the bearing or rods will do no help, the problem will repeat within seconds after starting. Time for a bottom end rebuild, only remedy now.
@pattywaktdiy41757 ай бұрын
@@bryanmiller9324 well that sucks. Sorry to hear that. I’ll be posting a video of my own soon on diagnosing this noise and how a top-end replacement fixed my issue, at least. All we can do as a Polaris community is combine our knowledge to try and avoid these very unwanted fixes!
@tazzharm6 жыл бұрын
Hi I have the same atv but 2006 and posted same kinda noise however it is when I drive it idle doesn't have the noise. did you figure it out. check out my vid. kzread.info/dash/bejne/iKKIyZlqXZOrZrg.html tell me if its the same and if you figured it out thanks
@1bananahands6 жыл бұрын
Tazzharm Crank bearings or rod bearing. I sold it
@aprilpratt55686 жыл бұрын
Have the same noise cany figure it out driving me nuts.
@1bananahands6 жыл бұрын
April Pratt , either the crank bearings or rod bearing. A lot of people say its normal but I wasn't okay with it.
@michael.filipenses41325 жыл бұрын
@@1bananahands did you fix what was it ??????
@philasselstine78165 жыл бұрын
april pratt u figure out what noise is i got same noise in my 04
@kayleesmart20842 жыл бұрын
I wanna know what it is too. My 06 500 ho makes the same noise.
Пікірлер
its the starter easy 80 dollar fix
It is rod slap you will eventually need to build the top end for any future wonderers common problems with them old sportsman's sorry for the let down.
Just the timing
Hello Sir can you tell me what the finaliment problem was? I'm in the same situation as you friendly
My 07 450 does that sound but only for a little bit after I start it and it just quits
About to do my first event through scda with my LGT wagon, any tips/major improvement I could make? Your EWG sounded sick too
So many things. Lol. Tires, suspension, BRAKES, better bushings and mounts. Also, be careful with the revs and watch your fuel usage. I ended up having a lean miss Because I ran out of fuel and combined with the heavy g-forces in the corners, Pretty sure I ran low or had a misahap with oil starvation and ended up throwing a rod bearing.
@@modshop1828 tank and jerry cans will be full!! I’m just finishing up with full Whiteline bushing/arms and tein coils w/ falken rt615k+ tires. I’m at 400whp on a iag stage 1. I’ve looked into the killer b baffle/pan/pickup but haven’t pulled the trigger yet
Flux Capacitor
its coming from the crank area. It's the balancer shaft. THey put junk bearings in the balancer shaft. You'd have to split the case and rebuild the whole damn thing. Just go with a Honda.
Fuck a honda every one we've had was nothing but junk always broken down
Sounds like the clutch to me. Maybe the hootinator valve? Could try doing a laser sweep on the crystal diodes? How many gigawatts of power is the flux capacitor getting? Should be 1.21
Ha ha, you're just kidding. It's clearly the balance actuators on the rotary girders divided by the rotational spacer weights on the automatic clutch shaft.
That’s the exact sound that my 2002 magnum makes. 😔
yeah the engine is gonna blow up soon it's a race going out and it blows thecasting out
Check the bendex that engages flywheel.
I did. I even ran it with the starter out. I ended up selling it but I believe it was the balance shaft.
My starter bendix gear only knocks under acceleration. Has been doing it since 1,200 miles. I now have 2,000 and nit any worse.
i acually think 1 of the cam shaft lobes is worn down and making the dull tick . it is a very common problem for 500 sportsman .
It's ur starter bro check ur starter or carnk case
She’s done
Did you find out what it was
My starter Bendix makes a noice just like that but for only 2 or so seconds when just starting my atv
Mine does to did you ever fix the problem
What was it?
A bearing in the bottom end. I just sent it down the road.
@@modshop1828 is it an expensive fix?
Some say its the valves chattering
Did you try and adjust the rockers? The cam wears and the rockers need adjustment after a while.
Hello, Did you find the fix? Mine is doing the same thing.
thatguydestroyedyou it is the bendix just replace mine easy fix
Great thanks, sold the bike lol. Made the buyer aware
@@honda400ex6 it's NOT the bendix. I replaced my bendix, BOTH buschings AND the bendix washer. And it STILL knocks. I have an 06 500 ho
Ever figure out what the problem was with yours I swapped everything out too same rattle
It is rod slap for any future wonderers it will eventually need a new top end build sorry for the news.
What was it?
Did he ever answer?
Timing chain tensioner
the bike im working on does the same thing but it goes away after a bit
Primary or secondary clutch.
I think it's the starter Bendix gear
starter bendix $30.00 cheep fix
Sounds like a bad rod or main bearing.
the bike im working on does the same thing but it goes away after a bit
What heatshields do you have by your right side where the exhaust pipe goes thru to prevent overheat
I had same exact noise and it was heat shield to lol.
Starter bendix
NATHAN JOHNSON , good idea but I took it out and ran it and had the same noise. It's gone now... sold it.
It has a bad connecting rod bearing
the bike im working on does the same thing but it goes away after a bit
If that's the case, replace it now while it's only a top-end disassembly. Quick job in under an hour.
@@pattywaktdiy4175To late now. Now the crank is damaged and it needs replaced. Changing the bearing or rods will do no help, the problem will repeat within seconds after starting. Time for a bottom end rebuild, only remedy now.
@@bryanmiller9324 well that sucks. Sorry to hear that. I’ll be posting a video of my own soon on diagnosing this noise and how a top-end replacement fixed my issue, at least. All we can do as a Polaris community is combine our knowledge to try and avoid these very unwanted fixes!
Hi I have the same atv but 2006 and posted same kinda noise however it is when I drive it idle doesn't have the noise. did you figure it out. check out my vid. kzread.info/dash/bejne/iKKIyZlqXZOrZrg.html tell me if its the same and if you figured it out thanks
Tazzharm Crank bearings or rod bearing. I sold it
Have the same noise cany figure it out driving me nuts.
April Pratt , either the crank bearings or rod bearing. A lot of people say its normal but I wasn't okay with it.
@@1bananahands did you fix what was it ??????
april pratt u figure out what noise is i got same noise in my 04
I wanna know what it is too. My 06 500 ho makes the same noise.
360 awhp 365 awtq
how much whp was made?
Nice bike