Пікірлер

• 
  @lancelanphier9509Күн бұрын

  Great video. But why didn't you put the lifters in oil and pump them up before you install them??

• 
  @dusty14986 ай бұрын

  Love the Elk on the Door ! Beautiful Job!

• 
  @bulamichael5917 ай бұрын

  Beautiful

• 
  @marcellemay77218 ай бұрын

  Man...I love this stove. I have an old Appalachian Stove 1981 vintage. It was actually a fireplace insert that I converted to a stand alone wood stove. I built a pedestal for it. It's a double wall stove with an envelope that goes bottom, top, back and sides with a blower fan that blows through the envelope...so that makes it really difficult to add a secondary air inlet anywhere except thru the door like you did. I'm gonna copy your design as the door is huge on this stove and I have room on both sides of the glass for draft knobs. I also want to do the glass wash like yours. This is awesome. How big are the air holes for the glass wash window frame?

• 
  @lonnielengkeek79 ай бұрын

  Or you can buy them for $3.50 a piece and that's what I did, saved a lot of time👌👈

• 
  @glenalguire69609 ай бұрын

  There are plenty of the old fishers stove they were the Bear series I’ve got one 30 inches by 24 , 3/8 walls and top and bottom , bullet proof not real fancy looking but not bad by any means , adding the secondary burn tube will increase efficiency by 60 plus percent for minimal, cost if you have a drill some good bits , a chop saw , and a cheap welder , ever one knows some who has these items if you don’t yourself , pick up steel at a scrap yard for Pennie’s a pound , I have these things , and could put one together in an hour easily with no special. skills

• 
  @glenalguire69609 ай бұрын

  The creosote is what you want to burn this is what he’s accomplished perfect

• 
  @jamesjarvis93110 ай бұрын

  I have had thieves try this five times in 7 years to open my c5 corvette's passenger door. I opened the door panel and locked the door with me inside the vehicle. I pulled the latch that the thieves tried to access with a coat hanger and the alarm went off when I opened the door. The rubber seal is insanely strong when the door is closed and no thief has managed to get a coat hanger into the door despite tampering with the rubber. Not only this, but there is almost no room to jam the rod down into the door because almost all of it is blocked. I do not believe it is possible to open the door without setting off the alarm and the rubber seal is insanely strong. It is like pushing against a house door with a car on the other side that is in park. I also eliminated any chance of the car getting stolen by putting a barrier around the whole device that is used to unlock the door. Now if the thieves ever get something down there, they will be bumping into a plastic case while staring at a camera. I also eliminated the lock cylinder's rod, so they will not be punching the lock to trick the car into opening the door for them.

• 
  @mayham6615 Жыл бұрын

  That is not a fix😒

• 
  @Ian-ij4of Жыл бұрын

  Thanks for posting this video, probably explains what's happened to my BMW engine, I found the rocker lying in the cylinder head, I've just been out and tried to compress the lifter and it's rock solid...hopefully I don't have to remove the inlet camshaft because it only lifts out so far and jams up against it....BMW N52 engine

• 
  @trevonelove305 Жыл бұрын

  Thanks helped me a lot.

• 
  @tylergeorge9266 Жыл бұрын

  This might sound dumb but to remove all the lifters and rocker arms on both sides do I have to rotate the engine at all? Cause I know some of those lobes on the cams are pointed up and down.

• 
  @gilthor Жыл бұрын

  Hey thanks I'm trying this with an older jeep but I'm struggling

• 
  @mariapatetta2242 Жыл бұрын

  Yo saved my day maan, great video 👏🏼 thanks!!!!

• 
  @Truthorshit Жыл бұрын

  Thank you

• 
  @PhatboyHD88 Жыл бұрын

  Put a rag or piece of rubber between the cam lobe and screw driver.

• 
  @kylekayser2291 Жыл бұрын

  Best stove I've ever seen best control.

• 
  @shaneonews6791 Жыл бұрын

  Just get solid lifters and rocker lockers.. problem solved.

• 
  @danmalloy3939 Жыл бұрын

  I am aware it could be the cam is worn even though it's not or the valve is not closing all the way even though it is so I have no idea

• 
  @danmalloy3939 Жыл бұрын

  Thanks dude I appreciate it I'm kind of having a different problem my rocker arm seems to wanna fall off just randomly and I replace the lifter and it still does it.

• 
  @GerryChopikRealtor2 жыл бұрын

  Pickling vinegar. 24 hrs. Done!

• 
  @lilsketlss93372 жыл бұрын

  Ï whant wane

• 
  @braintumor9432 жыл бұрын

  Dude what was it doing

• 
  @robertmerritt72712 жыл бұрын

  While your doing this if you have a 3.7l or 4.7l built before the start of the 2005 model year...obtain 2005 and up rocker arms with the small directional hole in the top. They keep more oil in the lifter and it is less likely to pump up and spit the arm out. Also, check for bearing slop in the cam follower wheel. I have found two that had .010" free play.

• 
  @talltom11292 жыл бұрын

  Poor attempt at this,thumbs down

• 
  @ELEKTRA_LUXXX2 жыл бұрын

  can this work with a 2007 Honda Element?

• 
  @deathcon66692 жыл бұрын

  I new it last year my truck did this and I got them push rodes new and the would not move like that o and I got like 9 of them that was all AutoZone had and I went to return them and they would not take them

• 
  @johnlong95342 жыл бұрын

  the electrode should not dissolve. The rust should dissolve and accumulate on the electrode..

• 
  @frankdavidson96752 жыл бұрын

  i use a rebar 6 in into tank filled with baking soda and water insulate this rod so i dont touch the tank i use a block of wood with a hole bored in ctr.wedge rod in hole so 6 in is inside tank leave air hole in wood ??? conn plus lead to rod neg lead to tank plung in charger leave all week end with no problems then diconect all and pour out rust water repeat if ness. cheap and no chem. used

• 
  @JS-xi5nk2 жыл бұрын

  Wow! NEVER EVER pry against the cam lobes. If you scratch them, then you are creating a friction point and causing wear on the lobe and roller. Instead, use a bent 10mm open end wrench between the spring and lifter and pry it up. And use a flat head or small pry bar against the rocker and head to pry the rocker back on.

• 
  @felixcat93182 жыл бұрын

  Beautiful stove, especially with your gorgeous Elk in the window. You could really see just how good that secondar burn was doing, it was wonderful. With the secondary burn the fire dance is really powerful and mesmerising. Thank you for sharing your stove and updates, subscribed.

• 
  @camilocaicedo28342 жыл бұрын

  Thank you

• 
  @recurringdreambusproject2 жыл бұрын

  Just to add a couple of things, all mine were stuck and a couple were stuck so bad I couldn't free them so I used a heat gun, fill the casing up to the bleed hole with penetrating oil and apply heat via a heat gun, do not over heat it just enough evenly applied all around until the fluid starts to bubble, one popped up just from the heat & one needed tapping upside down on wood, check the check valve at the bottom of the piston, they sometimes come out, you can check by turning upside down and apply light pressure to the spring clip, you can generally tell by looking at it at eye level, if it is out it will sit uneven, then check the valve by turning it the right way up and fill it with penetrating oil then push the ball at the bottom gently down with a straight pick, the oil will drain out if everything is working correctly.

• 
  @foxtrot7892 жыл бұрын

  I'm sorry but a video titled "How to..." and you fail to explain ANYTHING about the setup gets a thumbs down. Now, if you titled it "WHAT electrolysis does to rust" that'd make more sense. This isn't a 'How to', it's a 'what happens'.

• 
  @royvinator19452 жыл бұрын

  That sounds horrible. How's it holding up?

• 
  @alanncsu32433 жыл бұрын

  I'm wondering, so the overflow from the rusty tank isn't a problem for paint n the outside - while it's cooking?

• 
  @jakejake7083 жыл бұрын

  If you split the negative and circle the positive it'll speed up the process. Make sure to seal after you're done also

• 
  @geterdonegranny16393 жыл бұрын

  Thank you! I just watched your video and was able to get back into my jeep. Not only did I lock the keys in I also locked my phone in so I couldn't call for help! You did a fantastic job of explaining how the lock worked!

• 
  @emranmohammadiy14092 жыл бұрын

  How diid yu watch the video ?

• 
  @geterdonegranny16392 жыл бұрын

  @@emranmohammadiy1409 on a computer in the house.

• 
  @TheRoguelement3 жыл бұрын

  Dear Sir If your going to repair this do yourself a huge huge favor and purchase Marvel Mystery oil and dump a quart in your Jeep with every oil change and the inside of your motor will look like New

• 
  @jchancem213 жыл бұрын

  Hell yeah man. Saved me lock smith money

• 
  @noeffort2198 Жыл бұрын

  Mj

• 
  @whitedoug1213 жыл бұрын

  Man your a Flippin savior. Thank you

• 
  @i_n_t_e_l_l_i_g_e_n_c_e81093 жыл бұрын

  Always use NEW lifters, what you need are the springs and the seals contained in the new lifter that keeps your lifters pumped up with oil. Never start your engine without soaking your NEW lifters in oil overnight. Everything about this video is wrong and I will leave it at that.

• 
  @i_n_t_e_l_l_i_g_e_n_c_e81093 жыл бұрын

  A new set of lifters American made and high quality Melling sells for about 85 dollars for a complete set on Rockauto (welcome to the future) or you can buy even half price cheap Chinese for under $50 dollar a complete set on Amazon which is still a far better option than attempting to rebuild old lifters with weak springs and brittle seals. This video should be removed, you are misguiding people and having them risk critical engine failure that can not be fixed with lifters alone.

• 
  @lostnthe70s3 жыл бұрын

  I respect your enthusiasm,but that lifter isn't supposed to have that much play., according to the other mechanic.ive watched.????

• 
  @LRS14343 жыл бұрын

  Thank you very much. I got a 2000 Jeep Cherokee XJ and it took me about an hour to get it unlocked. But there's no way I could have done it without your video. The locksmith wanted $85.00. I'm very thankful for you showing me how the locking mechanism worked. And thank you for saving me $85.00

• 
  @mellsbells60753 жыл бұрын

  Lolol cleaning with science

• 
  @danielsmith24473 жыл бұрын

  I don't know how wise it is to put a screwdriver on the cam lobes, you can use a 10mm wrench with the open end bent at 90 degrees to pop them off at the lifter end. The hydraulic lash adjusters (lifters) only cost about five bucks each so no need to waste time disassembling them.

• 
  @johnparker19813 жыл бұрын

  You may consider consulting locksmith service in such situation, because sometimes do it by yourself cause more damage to your belongings. www.stcharleslocksmiths.com/

• 
  @dannistyles74713 жыл бұрын

  Thank you very much sir! Saved me & elderly mother crying on the roadside right before snowstorm. Life saver, time & money saver- no AAA needed! Thx a million!!

• 
  @blades22553 жыл бұрын

  Just did it with my pan head tanks amazing how good it works. Not a good as acid but its to dam hard tracking down acid these days. The biodegradable craps is truly just craps that doesn't work

• 
  @victoryfirst28783 жыл бұрын

  Do you think you could make some drawing of what you did ??? That would really help fella and thanks too.