well you might have persuaded me to keep it.. I'm just using for general DIY.. but I find changing the blades a total pain in the a***. The 3 part construction to hold the blades is very confusing and I find it almost impossible to get new blades fitted correctly. Parts of the blade holders keep getting damaged and bent and have to be replaced. A lot of dust gathers inside the construction of the blade holder too. The bolts to hold down the blade holder are not accurate sizing for me, they are like 8 mm, but they have a little bit of play.. so you have to be careful that the socket doesn't slip and round them off. I can't really afford 1/2 a day tp mess around ordering new parts and trying to remember how to get the new blades fitted and properly adjusted.. it's not really economical. A skilled job that is way beyond the average DIY'er and I consider myself to be a practical person.
@mk15handyman4 күн бұрын
For me it's amazing tool. I love it and never have any problems with it. It's way worth to keep it
@valleygirl6708 күн бұрын
i referred back to your video because i forgot how to do this again. Thank you for your help!
@mk15handyman6 күн бұрын
thx for watching and for your comment
@valleygirl6708 күн бұрын
strimmer is scandinavian for trimmer line
@HarveyJohnWillmott8 күн бұрын
If you aren’t going to use extraction on that router, you should at least wear a mask. That’s a load of carcinogenic shit you’re inhaling there.
@rafaelalviarez82609 күн бұрын
Thanks
@quentinhathcock584810 күн бұрын
Will the grease get into the sealed bearings where it's needed.
@user-ku9kx3fv5m11 күн бұрын
thx
@piowrob11 күн бұрын
thx. very helpful
@mk15handyman11 күн бұрын
thx for watching
@user-un3qt8zj6u11 күн бұрын
so helpfull
@mk15handyman11 күн бұрын
thx
@piotwro11 күн бұрын
good
@mk15handyman11 күн бұрын
thx
@user-nl3dz5ib9g11 күн бұрын
sorted, thx
@mk15handyman11 күн бұрын
thx
@TomTomSparrow11 күн бұрын
good video, thx
@mk15handyman11 күн бұрын
thx
@tomaszkys373512 күн бұрын
Thanks mate;-]
@mk15handyman12 күн бұрын
:) no worries. Thx for watching
@chrisb947813 күн бұрын
I carefully drilled & tapped a hole in the head of my FS70R, which had no grease port, and I installed a grease zerk. Works great.
@mk15handyman13 күн бұрын
Great. Thx for sharing with us
@MarzenaWira13 күн бұрын
thx ror review
@MarzenaWira13 күн бұрын
very helpful video. thx
@user-ku9kx3fv5m13 күн бұрын
so nice, I want one
@user-ku9kx3fv5m13 күн бұрын
great
@user-ku9kx3fv5m13 күн бұрын
so good video, thx
@piowrob13 күн бұрын
nice tool
@piowrob13 күн бұрын
great, I want one
@piowrob13 күн бұрын
thx so much, great video
@piowrob13 күн бұрын
thx so much, great video
@user-un3qt8zj6u13 күн бұрын
great
@user-un3qt8zj6u13 күн бұрын
I do have one, its amazing
@user-un3qt8zj6u13 күн бұрын
so good video, thx so much
@piotwro13 күн бұрын
I do have one and its ok
@piotwro13 күн бұрын
very nice, thx
@piotwro13 күн бұрын
life saving video :)
@piotwro13 күн бұрын
life saving video :)
@user-nl3dz5ib9g13 күн бұрын
thx
@user-nl3dz5ib9g13 күн бұрын
thx for video
@user-nl3dz5ib9g13 күн бұрын
cool machine
@user-nl3dz5ib9g13 күн бұрын
very nice and helpful
@TomTomSparrow13 күн бұрын
nice
@TomTomSparrow13 күн бұрын
thx
@TomTomSparrow13 күн бұрын
so great video. thx so much for so detail explanation
Пікірлер
well you might have persuaded me to keep it.. I'm just using for general DIY.. but I find changing the blades a total pain in the a***. The 3 part construction to hold the blades is very confusing and I find it almost impossible to get new blades fitted correctly. Parts of the blade holders keep getting damaged and bent and have to be replaced. A lot of dust gathers inside the construction of the blade holder too. The bolts to hold down the blade holder are not accurate sizing for me, they are like 8 mm, but they have a little bit of play.. so you have to be careful that the socket doesn't slip and round them off. I can't really afford 1/2 a day tp mess around ordering new parts and trying to remember how to get the new blades fitted and properly adjusted.. it's not really economical. A skilled job that is way beyond the average DIY'er and I consider myself to be a practical person.
For me it's amazing tool. I love it and never have any problems with it. It's way worth to keep it
i referred back to your video because i forgot how to do this again. Thank you for your help!
thx for watching and for your comment
strimmer is scandinavian for trimmer line
If you aren’t going to use extraction on that router, you should at least wear a mask. That’s a load of carcinogenic shit you’re inhaling there.
Thanks
Will the grease get into the sealed bearings where it's needed.
thx
thx. very helpful
thx for watching
so helpfull
thx
good
thx
sorted, thx
thx
good video, thx
thx
Thanks mate;-]
:) no worries. Thx for watching
I carefully drilled & tapped a hole in the head of my FS70R, which had no grease port, and I installed a grease zerk. Works great.
Great. Thx for sharing with us
thx ror review
very helpful video. thx
so nice, I want one
great
so good video, thx
nice tool
great, I want one
thx so much, great video
thx so much, great video
great
I do have one, its amazing
so good video, thx so much
I do have one and its ok
very nice, thx
life saving video :)
life saving video :)
thx
thx for video
cool machine
very nice and helpful
nice
thx
so great video. thx so much for so detail explanation
...
great advise
good explanation
great work
lovely jobly
beast
nice mover
...
thank you
so good toot. love it
thx. great tool
good tip
simple