Пікірлер

• 
  @hgvnovice201111 күн бұрын

  Just attempted to do mine same car. Not a chance got a friend with a garage cut the square off heat the nut and air gun it off with while was roasting. Terrible design

• 
  @mechanicallymindedmike9677Күн бұрын

  Horrific design!

• 
  @bunti6712 күн бұрын

  Found your Video, an hour to late. I don't know what genius engineer, got this idea for this mounting mechanism. Tried to change the Bumper in the backyard. Not possible. Next week in will destroy the bolds an cut open the the metall box an change everything. No wonder the hyundai car dealer wanted 900€ for the "simple" change of the rear bumper.

• 
  @mechanicallymindedmike967712 күн бұрын

  Horrid job init...

• 
  @bunti6712 күн бұрын

  @@mechanicallymindedmike9677 The worst. I wrote an articel in the german hyundai forum, to warn everybody. I asked another hyundai dealer and they told me, that their typical procedurce is to destroy the metal cover of then the nut, if it didn´t worked initialy with the impact wrench.

• 
  @bunti6711 күн бұрын

  @@mechanicallymindedmike9677 Just to be on the safe side. The lower nut also fits on the upper bolt, right? I have just ordered the new bolts for the top and the nuts for the bottom from Hyundai. Two bolts and four nuts together cost €85 in Germany. Here are the part numbers: bolts 55395A and for the nuts 54659.

• 
  @mechanicallymindedmike967710 күн бұрын

  I was able to reuse that aluminium square bolt. Didn't think to try the nut itself. Tysm for sharing the information. It'll help others tremendously

• 
  @bunti677 күн бұрын

  So. I finally got it done. The Nuts work for both. So before you start. Just purchase Two Bolts and four Nuts with the Partnumbers i wrote before.

• 
  @Fekillix17 күн бұрын

  The arrow on the tensioner on mine was about 10mm off when I changed it.

• 
  @mechanicallymindedmike967717 күн бұрын

  I'd always recommend changing by age or mileage for this exact reason...

• 
  @johncarroll99325 күн бұрын

  Possibly just a leak off pipe O ring. The diesel really sprays out. I had the same issue with the 1.8 tdci. Very cheap to replace, Lidl my have them. Just make sure to release the clip when pushing the pipe back in.

• 
  @user-zq4lh5re5t26 күн бұрын

  ❤❤❤

• 
  @Chillguy282027 күн бұрын

  Please tell the owner to clean his car

• 
  @7rodo27 күн бұрын

  Money shifta

• 
  @muflah28 күн бұрын

  Are you sure it wasn't abused?

• 
  @mechanicallymindedmike967727 күн бұрын

  2 owners current owner says they've had problems with clucth since they bought it (was 17ish k when bought)

• 
  @nakibislam1801Ай бұрын

  What route did the customer end up going with

• 
  @ricowswave1324Ай бұрын

  You have to do all that process just to replace that module? Hyundai and Kia made that really awkward tbh

• 
  @mechanicallymindedmike9677Ай бұрын

  Someone below has mentioned about removing rear subframe (dropping it down) the issue I find then is rear subframe bolts are rotten

• 
  @ryancrichton8910Ай бұрын

  Lad 4 bolts lower the subframe can pull it out from the back lot easier

• 
  @mechanicallymindedmike9677Ай бұрын

  You've seen these subframe bolts yeah... wish it was that easy. Hate these rust buckets

• 
  @Philip-dp6cyАй бұрын

  get it back out of permanent ignition mode

• 
  @mechanicallymindedmike9677Ай бұрын

  I'm sure it was just press once and it tuned off. If not press and hold for about 10 seconds

• 
  @Philip-dp6cyАй бұрын

  Hi how do i get the ignition lights out of permanent ON

• 
  @mechanicallymindedmike9677Ай бұрын

  Not sure what lights you're referring too. If you mean the DRL, then they're on permanently and dim when side lights or dipped light's are turned on. If you want to get out of permenant ignition on aka, out of diagnostics mode. Then you just press the start button once more and it'll switch off.

• 
  @aciddiver19782 ай бұрын

  Easypeasy😊

• 
  @djdemon92672 ай бұрын

  Love it, keep up good work

• 
  @trackattic2 ай бұрын

  Thanks

• 
  @mechanicallymindedmike96772 ай бұрын

  Glad it helped

• 
  @TheJohnson8612 ай бұрын

  What happens if it snaps/slips???

• 
  @mechanicallymindedmike96772 ай бұрын

  Engine will have a catastrophic failure.

• 
  @simbob3212 ай бұрын

  Just drill it out or use vice grips

• 
  @justinholmes56142 ай бұрын

  My father in law gave me one of these, it’s awesome

• 
  @mechanicallymindedmike96772 ай бұрын

  I agree mann..

• 
  @swms96792 ай бұрын

  This tool never works, just rounds off the screw

• 
  @justinholmes56142 ай бұрын

  Works every time for me

• 
  @HaraDayaful2 ай бұрын

  Really gotta make sure the bit seats correctly and deep.

• 
  @mechanicallymindedmike96772 ай бұрын

  If u use the right head, you get some decent results 80% of the time

• 
  @ACSharkey2 ай бұрын

  Impact driver

• 
  @mechanicallymindedmike96772 ай бұрын

  Thanks butt.

• 
  @trevorlahey14872 ай бұрын

  cheers mate appreciated for the info

• 
  @davem41312 ай бұрын

  What point were you referring to?

• 
  @tonykast19733 ай бұрын

  Thank you for your quick reply and information, you have been a great help, many thanks to you

• 
  @tonykast19733 ай бұрын

  Thanks Mike, that was really bugging me, I've had a look but I can't see how to turn of the reversing camera, mine comes on due to the canbus decoder, do you how to do it please.

• 
  @mechanicallymindedmike96773 ай бұрын

  So the newer models come with a same coloired wire pre cut and bridging them together turns it off. Others you'll need to use a multimeter. Find the wire that goes 12v feed positive when you go into reverse. Then chop that wire. Should sort you out mate.

• 
  @fatehranks3 ай бұрын

  Which wire do i need to disconnect on canbus for radio draining battery. Is it red and yellow ones

• 
  @mrlister20004 ай бұрын

  I'm a mobile tyre fitter, and those pin design locking wheel nuts are the bain of my life, as you can guarantee the garage monkey with his new F1 Airgun he got for Christmas will have used all the newtons available in his new toy to put those things back on. He will have also rounded the pins, making it useless. A friend of mine makes a living travelling the country removing those, and other typres of locking wheel nuts

• 
  @mechanicallymindedmike96774 ай бұрын

  That comment made me cry for you and also lol at same time. Don't envy you having to do that regularly mate. You're dead on thou!!

• 
  @Ruslans784 ай бұрын

  Is it worth it to do that by itself or it’s better bring to main dealer?

• 
  @mechanicallymindedmike96774 ай бұрын

  Depends how much money you got to spend fella.

• 
  @PeterGormanEnnis4 ай бұрын

  Thanks Mike. I like your comment at the very end. Hope you cooled off! I had to do this a good few years ago and I have to do it again. Like you said, you may have to swear, cry, get hurt etc.

• 
  @weiliu77114 ай бұрын

  My note e11 1.5dci is reliable car, 260000miles.

• 
  @mechanicallymindedmike96774 ай бұрын

  That is incredible mileage.. fairplay

• 
  @M.Zachary4 ай бұрын

  beautiful!

• 
  @b12jak514 ай бұрын

  Moving????

• 
  @mechanicallymindedmike96774 ай бұрын

  Yeah mann 🥰🥰.. To the bottom of your garden.. x

• 
  @pietroguidone71634 ай бұрын

  i found same problem on 1.4 petrol 8v....i dont know how happens...😮

• 
  @mechanicallymindedmike96774 ай бұрын

  Age and / or mileage buddy

• 
  @MrTutunka4 ай бұрын

  MAF looks fine. It went up to 120 on full throttle. Why are you recommending other things when you haven't even done the leak pressure and smoke test yet? Cut out the guesswork and find the problem the right way. Smoke test takes 10 mins

• 
  @mechanicallymindedmike96774 ай бұрын

  Maf was un plugged at that point m8

• 
  @mechanicallymindedmike96774 ай бұрын

  Watch the video in full. I tested the MAF. Maf reads at 81 degrees Celsius with a cold engine. Engine off. Smoke test won't help me on this occasion 😫

• 
  @gearhead6.06 ай бұрын

  I have been trying to figure this out for hours! Watching videos accessing settings I don’t have. Hooked up my vag com trying to find the trigger and turn it off… I haven’t tried this yet but I know for sure this is going to work! I have a digital mirror that does my cameras so I obviously want to turn it off on the deck! I owe you a steak dinner sir! If you are ever in Ohio hit me up 😂

• 
  @mechanicallymindedmike96776 ай бұрын

  Glad I helped a brother out... keep it real mann.

• 
  @geromefrieler96516 ай бұрын

  "promo sm"

• 
  @Manu-Official6 ай бұрын

  140bhp on a basic tune 😆

• 
  @mechanicallymindedmike96776 ай бұрын

  Correct. Look at as many sites as you can locate for stage 1 figure's and see what you can get. Be great to hear your feedback. I have my support from a company called Max Tune which is a well established business, with excellent feedback and well established business.

• 
  @Manu-Official6 ай бұрын

  @@mechanicallymindedmike9677 I'm sorry, I don't look for sites - full custom tune from a local Audi specialist instead... Reason is, if it ever went wrong I don't have to talk to a screen.

• 
  @mechanicallymindedmike96776 ай бұрын

  OK.

• 
  @rustywreck33516 ай бұрын

  Never ever !!! clamp the brake hose directly with vice grips

• 
  @acellpage7 ай бұрын

  In some stereos there are a pink or brown confirm what goes live with 12v in reverse before cut it mi stereo have a hiworld module and in my case it was the pink one. 👐

• 
  @mechanicallymindedmike96777 ай бұрын

  Good share m8... just had another headunit recently. This 1, wire was green, already cut and actually required a closed loop to disable the black screen

• 
  @b12jak517 ай бұрын

  Wicked m8

• 
  @christiansaunders5967 ай бұрын

  Have you removed the front bummer? Had the worst instructions with mine

• 
  @mechanicallymindedmike96777 ай бұрын

  Yes m8.. then refit bumper once brackets are mounted

• 
  @davidhenderson77225 ай бұрын

  Considering buying one of these for my t4. Will it pass the mot with it fitted? 🤔 also does the bumper need cutting on the bottom to clear the bumper? 🙂

• 
  @mechanicallymindedmike96775 ай бұрын

  No cuts needed. Not to sure on vosa testing rules tbh butt. (Sorry)

• 
  @Beebop-ow9ge8 ай бұрын

  That didn’t “last 4 years” by the looks of it, it lasted 2 years but was in a vehicle for 4 😂

• 
  @mechanicallymindedmike96778 ай бұрын

  Lol... proper dodgy...

• 
  @chevycamaro68838 ай бұрын

  Naw man its in good shape..put it back .roflmao

• 
  @mechanicallymindedmike96778 ай бұрын

  Wire wheel and fresh paint 1st... be job done

• 
  @TackFunks8 ай бұрын

  Thanks man, worked 🤝

• 
  @mechanicallymindedmike96778 ай бұрын

  Glad it helped m8

• 
  @b12jak519 ай бұрын

  Hell of an uplift, brilliant job. Recomend to anyone

• 
  @vw_mods_47119 ай бұрын

  Hi great info, I had my timing belt done on mine about 5k miles ago when I removed the cover last week to clean something, I noticed that the arrow wasn’t in the middle! Does it move or should it be in the middle constantly? As I put it back on and drove a bit and it was looking better, but not quite central.

• 
  @mechanicallymindedmike96779 ай бұрын

  Hiya, yes it will move slightly. But we're talking marginally. At this point, engine was timed. The arrow should be bang on for sure. (Hope that makes sense mate?) When doing timing belt also recommended you change cam sensor too. Quite recently I've had a sensor fail on customer's van 5 k n4 belt due for change. So it's something I'd recommend changing now when booking belt jobs on this engine type

• 
  @vw_mods_47119 ай бұрын

  @@mechanicallymindedmike9677 yeah makes sense. Thanks for the reply will change the sensor next time 👊👊👊

• 
  @josephbidon433310 ай бұрын

  My module failed after 7 years, stuck on side of a road with the brake locked up. Had to tow to my local tyre shop. These modules are made in China for Hyundai, so I bought mine about half the price the dealer wanted just to supply, fitting was Hyundai "standard rates". My local tyre shop fitted everything up for about 1/3rd of the cost the dealer wanted. Works perfectly. Thought about doing this myself until I saw this video....too much headache for me.

• 
  @mechanicallymindedmike967710 ай бұрын

  g.co/kgs/8GsWnj Depending where you are m8. I would of helped

• 
  @livefreeordie576910 ай бұрын

  👍🏽👍🏽

• 
  @giece623710 ай бұрын

  Hello ;) I have a slightly similar problem, I get a black screen, but only from time to time. The camera works fine for a few days and then suddenly there is a black screen. the next day everything works fine again etc...Can anyone help me? Thank you

• 
  @mechanicallymindedmike967710 ай бұрын

  Are u sure connections are well tight and solid m8? Try doing a reset on headunit.

• 
  @RANDEEP68510 ай бұрын

  Hello mate would you know where the skoda rapid 2014 one will be I’ve taken glove box out but can’t see it any where

• 
  @mechanicallymindedmike967710 ай бұрын

  I've not done 1 on that car sorry buddy