I have a 2008 ultra classic. Mine is doing the opposite. New clutch, new cable. Adjusted and still slipping. IDK
@scottkleyla77529 күн бұрын
Worn spline gears not matching uo,worn main shaft bearing,main gear shaft travel from wear to far more or less from prime seat position due to wear at the cover plate seat area maybe,just worn bushings and race and bearings around travel shafts...?
@RicardoMartinez-mn3sn10 күн бұрын
Where’d you get those mufflers? And do they sell just the heat shields
@Sundown70211 күн бұрын
After adjusting your clutch Check the shift rod that goes from your foot shifter to the transmission to make sure the Transmission tongs are in the correct position (According to the manual). Sometimes I've had to screw the shift rod adjustment a little to match what the manual specifies which makes hitting neutral much easer
@alexandernvelez675613 күн бұрын
I just got mine but both my yellows are always on as well.
@owenpetrey110513 күн бұрын
Does she ride 2 up with you with that seat? If so, does she have complaints?
@panjiliphe658626 күн бұрын
same pb 4 me
@mike719728 күн бұрын
Great video! Sounds ike PO just didn't want to deal with his issue, can't believe he rode it like that. Glad you got it fixed, very informative.👍
@joshuaramos9676Ай бұрын
After all this time is it still going strong?
@ManpackedPOVАй бұрын
Do you have to remove the tank to remove the cables ?
@DaivdBlessingingsАй бұрын
Any sbujsting welcome
@DaivdBlessingingsАй бұрын
Here's my projust is putting a 50 cc mini bike motor with kick start done with the pedaling crap
@trillytrell3475Ай бұрын
Video 🚮
@paulb5599Ай бұрын
You couldve at least fast forwarded parts of it
@lassassin2239Ай бұрын
😂 i bet she was talking shit
@jacebarton7426Ай бұрын
Do you have the rough textured transfer case? If so how do you clean yours?
@twinsmotogarage1866Ай бұрын
Usually just soap then spray with S100 engine brighter. www.amazon.com/dp/B000WK111K/ref=cm_sw_r_as_gl_api_gl_i_4X72PWW04PKKY6KT5AX9?linkCode=ml2&tag=twinsmotoga01-20
@jacebarton7426Ай бұрын
@@twinsmotogarage1866 dawn dish soap?
@TDStanton-ed1lcАй бұрын
U managed to make changing a fender look hard
@SMELLSLIKENIRVANATRIBUTEАй бұрын
What's the difference between yours Progressive Suspension 11-1527 18.5 Progressive Rate Fork Spring,Black verses the 11-1577 that only shows on their website for a 2019 Harley 883?
@jacobflorez9703Ай бұрын
What sissy bar do you run ?
@twinsmotogarage1866Ай бұрын
This one is detachable. I think it’s from Harley.
@tristan-valiant-thorАй бұрын
Took my cable out and now it won’t thread back in at all, I can literally slide it in and out without threading it, not sure what change 🤔
@twinsmotogarage1866Ай бұрын
Look at the treads on the cable and the threads on the primary cover. See which ones are messed up.
@combustablelemons8988Ай бұрын
So this is a ridiculous question but where does the hot wire hooked to the starter go? Because this sportster I just picked up has another one that goes to the harness and the one on the starter. Do they go on the same battery terminal or what?
@twinsmotogarage1866Ай бұрын
If I remember correctly there is a big wire that goes directly from the battery or main harness to the solenoid. There is a small trigger wire that goes from the relay to the solenoid.
@rudddyna0671Ай бұрын
Can i have the wheel brand
@chrissteele6130Ай бұрын
oetiker clamp, at HD engineering they pronounce it "OH-Ticker" clamp. My friend has 2012 "Forty-Eight" XL1200X. This is the same place his is leaking, thanks for the video.
@mikereed6957Ай бұрын
My 04 fatboy is only clicking, and the battery is charged. Idk whats going on. This is the first video on my quest to diagnose.
@kraven92032 ай бұрын
I was told that the 1200 tank would not fit a 883 so ty for this.
@ronaldgonzales51132 ай бұрын
Does the rear bar interfere with mounting and dismounting the bike or back up the back ?
@Palehorse422 ай бұрын
I was 4K miles into mine, “break in period”. The seat is garbage and uncomfortable for anything longer than an hour. You might as well be sitting on a brick. DO NOT BUY
@twinsmotogarage18662 ай бұрын
The SDC pro seems to have pretty good resale. Hopefully you were able to recoup some of your money. I've done 10 hour days on it and absolutely love it. To me the soft seats that look comfortable are no good after an hour.
@Timhays892 ай бұрын
What is the hose called that is next to that one and looks similar and loops under and upwards and has a plastic cap in the end?
@kencappel45112 ай бұрын
Was it hard to get the exhaust hanger bolt out, I don't want to break it. Any suggestions? Tia
@johnmatics26552 ай бұрын
Try the minimum AMT of primary fluid
@rafaelbeltran1932 ай бұрын
I have a 2021 sporster 883, think if i buy the gauge speedometer mount you did, it would still work for my sporster? I was also planning on doing a road warrior fairing on it, think it would still work?
@twinsmotogarage18662 ай бұрын
I think the speedo mount would work. Can’t say I’ve seen a road warrior on a 39mm front end. I’ve ran the Amazon repop T-Sport on a 39mm front end thought
@OddBall922 ай бұрын
Would it be a good idea to wrap the hose w EZ fuse tape? Same thing ppl use on the wire tuck
@twinsmotogarage18662 ай бұрын
Could try and make a sheath for it with loom or something. I wouldn’t though. It lasted 10 years and was easy enough to replace.
@818jake2 ай бұрын
Academy on I-10
@tashathayer40692 ай бұрын
I don't trust all relays,you never know if someone bought one & returned the bad one,Id have got another one. Not much annoying then tearing apart anything just to replace Junk & need redo again. Hope ur bikes better. ✌
@Sean-uc5vj2 ай бұрын
Did you paint the SDC logo black bc all the sdc seats comes with white logos. I called and it can’t be custom ordered/changed from saddlemen.
@sfnative98612 ай бұрын
Remove battery it's makes it easier
@adrianbec48342 ай бұрын
did you custom order the black logo?
@twinsmotogarage18662 ай бұрын
The TwinsMG?
@adrianbec48342 ай бұрын
@@twinsmotogarage1866 on the sdc saddlmen seat usually the sdc seat logo is white but you have it blacked out
@Sean-uc5vj2 ай бұрын
Probably spray painted it with automotive vinyl upholstery paint
@adrianbec48342 ай бұрын
@@twinsmotogarage1866 the sdc logo
@clubstyleridahd46953 ай бұрын
Mine clicks when i first start it up after not running it for a week. the first start it clicks then the second it starts right up. After i ride it around any start ups it acts normally. What do you think it is? The relay? Or just a battery slowly dieing?
@twinsmotogarage18663 ай бұрын
Sounds battery related. Id start with keeping it on a charger.
@r_itchytrigger3 ай бұрын
Looks like that thing hadn't been parked indoors since it left the dealership. What a shame. But great job reviving the beast!
@twinsmotogarage18663 ай бұрын
This bike had over 100,000 miles on it. Someone had been enjoying it for sure. Thanks for watching!
@elzer01813 ай бұрын
Have you got the old Dyna 39mm front end or new Dyna forks 49mm?
@twinsmotogarage18663 ай бұрын
This was on a 39mm front end.
@billyhodgson36473 ай бұрын
I only put my rain sock when it's raining. I put a powder sock on my snowmachine and it restricted the air flow massively.
@paologiorgini98213 ай бұрын
Metti olio 85w140
@seanreed67803 ай бұрын
watching you load that thing was the most stressful experience of my life, not even bested by a time I almost sent my buddies truck off a 30 foot ridge
Пікірлер
Damn Harleys, always something
exist this conversion for rear brakes?
I have a 2008 ultra classic. Mine is doing the opposite. New clutch, new cable. Adjusted and still slipping. IDK
Worn spline gears not matching uo,worn main shaft bearing,main gear shaft travel from wear to far more or less from prime seat position due to wear at the cover plate seat area maybe,just worn bushings and race and bearings around travel shafts...?
Where’d you get those mufflers? And do they sell just the heat shields
After adjusting your clutch Check the shift rod that goes from your foot shifter to the transmission to make sure the Transmission tongs are in the correct position (According to the manual). Sometimes I've had to screw the shift rod adjustment a little to match what the manual specifies which makes hitting neutral much easer
I just got mine but both my yellows are always on as well.
Does she ride 2 up with you with that seat? If so, does she have complaints?
same pb 4 me
Great video! Sounds ike PO just didn't want to deal with his issue, can't believe he rode it like that. Glad you got it fixed, very informative.👍
After all this time is it still going strong?
Do you have to remove the tank to remove the cables ?
Any sbujsting welcome
Here's my projust is putting a 50 cc mini bike motor with kick start done with the pedaling crap
Video 🚮
You couldve at least fast forwarded parts of it
😂 i bet she was talking shit
Do you have the rough textured transfer case? If so how do you clean yours?
Usually just soap then spray with S100 engine brighter. www.amazon.com/dp/B000WK111K/ref=cm_sw_r_as_gl_api_gl_i_4X72PWW04PKKY6KT5AX9?linkCode=ml2&tag=twinsmotoga01-20
@@twinsmotogarage1866 dawn dish soap?
U managed to make changing a fender look hard
What's the difference between yours Progressive Suspension 11-1527 18.5 Progressive Rate Fork Spring,Black verses the 11-1577 that only shows on their website for a 2019 Harley 883?
What sissy bar do you run ?
This one is detachable. I think it’s from Harley.
Took my cable out and now it won’t thread back in at all, I can literally slide it in and out without threading it, not sure what change 🤔
Look at the treads on the cable and the threads on the primary cover. See which ones are messed up.
So this is a ridiculous question but where does the hot wire hooked to the starter go? Because this sportster I just picked up has another one that goes to the harness and the one on the starter. Do they go on the same battery terminal or what?
If I remember correctly there is a big wire that goes directly from the battery or main harness to the solenoid. There is a small trigger wire that goes from the relay to the solenoid.
Can i have the wheel brand
oetiker clamp, at HD engineering they pronounce it "OH-Ticker" clamp. My friend has 2012 "Forty-Eight" XL1200X. This is the same place his is leaking, thanks for the video.
My 04 fatboy is only clicking, and the battery is charged. Idk whats going on. This is the first video on my quest to diagnose.
I was told that the 1200 tank would not fit a 883 so ty for this.
Does the rear bar interfere with mounting and dismounting the bike or back up the back ?
I was 4K miles into mine, “break in period”. The seat is garbage and uncomfortable for anything longer than an hour. You might as well be sitting on a brick. DO NOT BUY
The SDC pro seems to have pretty good resale. Hopefully you were able to recoup some of your money. I've done 10 hour days on it and absolutely love it. To me the soft seats that look comfortable are no good after an hour.
What is the hose called that is next to that one and looks similar and loops under and upwards and has a plastic cap in the end?
Was it hard to get the exhaust hanger bolt out, I don't want to break it. Any suggestions? Tia
Try the minimum AMT of primary fluid
I have a 2021 sporster 883, think if i buy the gauge speedometer mount you did, it would still work for my sporster? I was also planning on doing a road warrior fairing on it, think it would still work?
I think the speedo mount would work. Can’t say I’ve seen a road warrior on a 39mm front end. I’ve ran the Amazon repop T-Sport on a 39mm front end thought
Would it be a good idea to wrap the hose w EZ fuse tape? Same thing ppl use on the wire tuck
Could try and make a sheath for it with loom or something. I wouldn’t though. It lasted 10 years and was easy enough to replace.
Academy on I-10
I don't trust all relays,you never know if someone bought one & returned the bad one,Id have got another one. Not much annoying then tearing apart anything just to replace Junk & need redo again. Hope ur bikes better. ✌
Did you paint the SDC logo black bc all the sdc seats comes with white logos. I called and it can’t be custom ordered/changed from saddlemen.
Remove battery it's makes it easier
did you custom order the black logo?
The TwinsMG?
@@twinsmotogarage1866 on the sdc saddlmen seat usually the sdc seat logo is white but you have it blacked out
Probably spray painted it with automotive vinyl upholstery paint
@@twinsmotogarage1866 the sdc logo
Mine clicks when i first start it up after not running it for a week. the first start it clicks then the second it starts right up. After i ride it around any start ups it acts normally. What do you think it is? The relay? Or just a battery slowly dieing?
Sounds battery related. Id start with keeping it on a charger.
Looks like that thing hadn't been parked indoors since it left the dealership. What a shame. But great job reviving the beast!
This bike had over 100,000 miles on it. Someone had been enjoying it for sure. Thanks for watching!
Have you got the old Dyna 39mm front end or new Dyna forks 49mm?
This was on a 39mm front end.
I only put my rain sock when it's raining. I put a powder sock on my snowmachine and it restricted the air flow massively.
Metti olio 85w140
watching you load that thing was the most stressful experience of my life, not even bested by a time I almost sent my buddies truck off a 30 foot ridge
good job looks much better
Clutch hub bearing in the clutch basket
Can you elaborate?
Part number ?
In the description
It could be your compensator going bad.
How do you figure?
what year of bike ?
This was on an 2009