Пікірлер

• 
  @tommycch233 ай бұрын

  hi can you share the setting of cb？

• 
  @pongringmei66723 ай бұрын

  where should we put relay in thus model ? someone please reply

• 
  @Kkmahtofficial7 ай бұрын

  I need E tap software

• 
  @richardemery66909 ай бұрын

  On bus fault why doesn’t CB5 operate before the generator CB?

• 
  @user-cm4pu7tl3w Жыл бұрын

  Thank you very much sir for your explicit explanation this is what I have been looking for🙏

• 
  @bryannaftali1652 Жыл бұрын

  can you make a diffrential protection for generator?

• 
  @yassiremad6407 Жыл бұрын

  Enable subtitles please.

• 
  @cbsuresh5631 Жыл бұрын

  There are 3 types. of CTs.. 1.metering 2.general protection (unit protection) 3.Special protection(Zone protection)

• 
  @sarweashrao3001 Жыл бұрын

  Amazing sir,thank you!!!!!!!

• 
  @muhammadshaheer8644 Жыл бұрын

  Sir I would like to request to upload videos about Unsymmetrical fault

• 
  @vaporya Жыл бұрын

  Please make a video about the operation between recloser,LBS and fuse

• 
  @almikntolkein74892 жыл бұрын

  great work

• 
  @almikntolkein74892 жыл бұрын

  watching 1 day before paper 😭

• 
  @tutor4u3982 жыл бұрын

  Sir g low voice quality

• 
  @YouTubeBillionaire952 жыл бұрын

  Loud voice 👍🏻

• 
  @user-rj6ck6go5e2 жыл бұрын

  Thanks

• 
  @azeezurrahman3822 жыл бұрын

  It's very knowledgeable session.. thanks for sharing your experience with users..

• 
  @aqibsaeed44012 жыл бұрын

  Sir it show error. Like energized busses is less than 2.

• 
  @hfe18332 жыл бұрын

  Thanks for providing this video, really helps me alot, by the way to how display transformer load in percentage?

• 
  @suryanarayansahu63273 жыл бұрын

  Please help me, I have a doubt in Differential relay

• 
  @raimonbawazir54493 жыл бұрын

  thank you for this video. I have a problem with my system. I need some help. can I have your email?

• 
  @electricalworld8173 жыл бұрын

  My whatsapp no: +92-302-1025852

• 
  @prashanthgaitonde34517 ай бұрын

  @@electricalworld817 is this number still working sir

• 
  @alqadritv75833 жыл бұрын

  You are not work on your Channel so thats way you give me your channel

• 
  @alqadritv75833 жыл бұрын

  Hy sir how are you i hope you good.please send your email or contect number

• 
  @mathshomework31413 жыл бұрын

  Hey, thank you for your video, on etap 16.2, I tried to replacate the IEEE1.udm model but I'm obtaining different output between the original one and the replacate. I noticed the input is changing each time I draw a new udm. My question to you is : is it normal that the input changes like that? And how can I control the input?

• 
  @mathshomework31413 жыл бұрын

  Hey, thank you for your video, on etap 16.2, I tried to replacate the IEEE1.udm model but I'm obtaining different output between the original one and the replacate. I noticed the input is changing each time I draw a new udm. My question to you is : is it normal that the input changes like that? And how can I control the input?

• 
  @BabaJee933093 жыл бұрын

  please show us how to make generator damage curve coordination , if the system has another source (Utility).

• 
  @BabaJee933093 жыл бұрын

  Very informative lecture, thank you Sir.

• 
  @electricalsyallabus50933 жыл бұрын

  sir also make a vidio for giving tha rating or equipment your session is very helpful for me thanku

• 
  @electricalworld8173 жыл бұрын

  thank you for your appreciation. below is the link of video regarding system modelling (equipment rating): kzread.info/dash/bejne/oXmtk69wqt27drQ.html

• 
  @kholil46483 жыл бұрын

  👍👍👍 thx

• 
  @veeraragavan69813 жыл бұрын

  Both Gen are same capacity still second one delivers less power How to bring same mw in Both gen

• 
  @electricalworld8173 жыл бұрын

  this is because 1 gen is in swing mode and the other is in voltage control. The output of voltage control gen is fixed (MW). TO bring both gen to same power, try making them swing generators.

• 
  @aamirahmed76593 жыл бұрын

  Outstanding sir, Thank you ao much !

• 
  @affanain79433 жыл бұрын

  Thank you, Sir! Your way of explanation is great.

• 
  @best5tv2454 жыл бұрын

  sir plz tell us what is difference between normal and swing generator and what is the purpose of their usage here??

• 
  @electricalworld8174 жыл бұрын

  Swing generator is normally used to make up active and reactive power deficit in the systems. PV and MVAR generators have constant power outputs.

• 
  @ziaurrehman26724 жыл бұрын

  thanks sir

• 
  @zainuddinkhan82744 жыл бұрын

  Very grateful for the initiative, sir.

• 
  @abduljalalhasas22144 жыл бұрын

  Thank u Sir

• 
  @muhammadumerbaig36074 жыл бұрын

  Sir can we lectures on Autocad?

• 
  @electricalworld8174 жыл бұрын

  Sure I will try to cover that also after this.