Пікірлер

• 
  @gpsperez51934 күн бұрын

  Why my blower motor overheats? Smokes

• 
  @Roadhvac2 күн бұрын

  Is this blower motor removed from the furnace, and if so, I explained in my video that you will need to create a restriction. If you are familiar with an amp meter, try reading reading the motor specs. You are probably drawing too many amps, which will cause the motor to overheat. The more restriction you put in front of your blower should lower the amps, assuming this is a direct drive motor and not belted. Hope this helps. Appreciate your comment.

• 
  @roseward14859 күн бұрын

  You forgot about the lime ...

• 
  @Roadhvac9 күн бұрын

  You are so right

• 
  @roseward14859 күн бұрын

  ❤ My Beauty Queen... Seba ...

• 
  @roseward14859 күн бұрын

  MAGNIFICENT...

• 
  @roseward14859 күн бұрын

  ❤ The Garden is marvelous Kim ...

• 
  @jrc63015 күн бұрын

  And if u have a 90% furnace and don't use a filter , your secondary coil will get clogged and A coil too cutting ur air flow and hurting ur wallet $$$ fyi great video sharing 😅😅😅

• 
  @Roadhvac15 күн бұрын

  Yes, you are so right back in the day it was the A coil that would get plugged up. Now, it is your recoup /secondary on all these 90+ efficiency furnaces.

• 
  @Thedrummaman7622 күн бұрын

  First time for everything, good work!

• 
  @tstatech24 күн бұрын

  I do it all the time. You pull the motor and wheel out of the housing, wash the wheel, blow out the motor with compressed air and put it back together. Less than an hour

• 
  @Roadhvac23 күн бұрын

  We never had compressed air on our service trucks. Most companies never did that on check and cleans.

• 
  @shawnflanagan50313 күн бұрын

  I did too when I was residential tech

• 
  @shawnflanagan50313 күн бұрын

  @@Roadhvac *clean and check

• 
  @user-su5ft8lc9qАй бұрын

  Man you Sire are a GENIUS, your wife owns some special attention tonight at supper. Desert of your choice

• 
  @RoadhvacАй бұрын

  LOL

• 
  @MacieFloria3 ай бұрын

  Yassss grandpa -Macie

• 
  @tux7073 ай бұрын

  Did the traction light go off?

• 
  @Roadhvac3 ай бұрын

  Yes, that wire was disconnected .

• 
  @Roadhvac3 ай бұрын

  Yes, it did. That went to the anti-lock brakes .

• 
  @cohort61593 ай бұрын

  I had a similar Lasko fan. It was remote control. The motor would screech and eventually slow and bind up. Three times I disassembled it to get to the bearings and greased them up with moly grease. It worked for a few weeks each time and then failed again. I got maybe one extra year of use out of it and finally threw it away.

• 
  @Roadhvac3 ай бұрын

  Yes, I know what you mean. Sometimes, I wonder if it's worth it. I've had to steal wool the shaft before it gets a little corroded. I appreciate your comment.

• 
  @bobrussel5244 ай бұрын

  Yep, I worked as a kid in a 3 bay service station with 3 mechanics. My job during the fall was changing tires some days spent 8 hours days doing nothing else but working the tire machine. When I came across a tire that needed a repair due to a nail I would not only plug the hole but patch the inside as plugs do fail I found out. So it was a rule in our shop if you plug a tire take it off the rim and patch it. you might consider doing that just find a garage that with a tire machine and have them patch it.

• 
  @Roadhvac3 ай бұрын

  Yes, I agree. I would of signed a waiver if they would of asked. Think there 10 year policy sucks. Thanks for your comment.

• 
  @MacieFloria4 ай бұрын

  Ya grandpa!!!!

• 
  @ameliawarwas76924 ай бұрын

  The cat is so cute

• 
  @Roadhvac4 ай бұрын

  He loves me

• 
  @Olimpia-rf6qt4 ай бұрын

  Luvcat❤

• 
  @spike02264 ай бұрын

  Went with 250’s on my 11’ clamshell which were exact replacements for the original. (LaVanture LGP10-280-250 28”) They are strong.

• 
  @Roadhvac4 ай бұрын

  Thanks for that info. My old ones were unreadable. These new ones probably won't last long then. 👍

• 
  @roseward14855 ай бұрын

  Boogie Woogie ...❤

• 
  @roseward14855 ай бұрын

  What is that.😂😂😅

• 
  @OkRobin_rr6 ай бұрын

  I’m actually Native American as well, well I’m assuming you are atleast

• 
  @Roadhvac5 ай бұрын

  My grandfather was full blooded. He taught me alot.

• 
  @wideputin1096 ай бұрын

  errrr, nice song

• 
  @Poopyhead34526 ай бұрын

  Dang nice

• 
  @LegoNerdPuristCustoms6 ай бұрын

  Cool

• 
  @TaylorPellonari7 ай бұрын

  that cat is so cute

• 
  @Roadhvac5 ай бұрын

  He is a lover boy.

• 
  @shatnersufolanded77857 ай бұрын

  How can it charge with out an alternator,stator,voltage regulator and just charging magnets. That stupid bracket is there so you dont stick your hand in there and cut your finger off.

• 
  @Roadhvac6 ай бұрын

  It probably won't charge but all you need is a battery to start it. That is the reason I did it Because it was so hard to pull start.

• 
  @Roadhvac8 ай бұрын

  except you let a furnace blower run long enough with no load and it will burn up the motor unlike a vacuum. because your amp draw will be too high.

• 
  @mistyleejackson32418 ай бұрын

  Your problem is the ice maker needs to be in the freezer DUH! ice has to be kept more colder to stay ice! So who ever put an ice maker in an refrigerator ? Need their ass kick 🦵!! REAL TALK FOR THE ASS!! 42 yr old who loves jb

• 
  @stepanbalakirev84228 ай бұрын

  I have an old french door samsung, worked for over 10 years and started ice buildup, so far I found the thermal fuse is blown and the temp sensor is not working either. but it has not had any ice buildups before that. What I noticed is the defroster is WAY bigger 244watt vs 100-120watt that comes on the newer ones, so that prolly helps a ton. Will see if replacing the fuse and sensor solves the problem if not I'll prolly get the secondary silicone heater. The fridge was cheap and its a fun project (not my only fridge, but once fixed will replace mine)

• 
  @Roadhvac7 ай бұрын

  This frigerator has definitely been a headache

• 
  @troysleeper32828 ай бұрын

  I have a 230 voltage fan blower motor and it is a A o Smith fan blower motor and I was wondering on the wire diagram on the motor it says that the line wire is the yellow line wire and between it is the blue wire with a line between the yellow and blue wire would I hook those to wire to gather I have a 2 wire setup and I want to use the red wire for low speed.

• 
  @thisisyourcaptainspeaking22598 ай бұрын

  You didn't mention the capacitor.

• 
  @Roadhvac8 ай бұрын

  Easier if I could see the diagram on the side of the motor

• 
  @billyclough75009 ай бұрын

  How much they sell for?

• 
  @Roadhvac9 ай бұрын

  You should be able to pick one up for 20/30 dollars. Any furnace replacement. Usually, the blower motor is always good.

• 
  @josephwheeler55949 ай бұрын

  Nice tiller!

• 
  @Roadhvac9 ай бұрын

  Some people just need to take the time to look at what they are throwing out

• 
  @ddb11439 ай бұрын

  Question 1: If I use a furnace blower for sucking out welding fumes in about 4 points of use, all at the same time, is that enough restriction to make the motor work hard enough (avoid free-wheeling) so it doesn't draw high amperage? Question 2: Should I design a filter to create some resistance, but also lower the amount of unfiltered, dirty, welding smoke that makes it to the fan blades?

• 
  @Roadhvac9 ай бұрын

  Just restric the exhaust of the blower. And yes, filter the intake . Maybe build a box to put the blower in.

• 
  @ddb11439 ай бұрын

  Yes, I did build a metal box that the blower is mounted in. It is completely enclosed but with 8" duct ports on each side that line up with the fan diameter. The exhaust port is also the other hole in the case, same square size as the fan exhaust hole. Thanks for your video and input. I will measure the amp load when it is being used at each of the 3 speed line conductors. What do you suppose are safe amp loads? 1/2 hp Century motor. The filters are inside at the 8" ports. First is a metal pre-filter to catch any possible sparks, then a paper filter, merv 8. The filters are 10" x 10" x 1" thick each. They are mounted with metal pcs. to keep them in place and are easy to replace.

• 
  @Roadhvac9 ай бұрын

  The maximum amp draw should be specified on your motor tag if it is still readable it can very. usually no more than 6.6 amps.

• 
  @jayhadcock87679 ай бұрын

  Samjunk 😂

• 
  @jayhadcock87679 ай бұрын

  Problem is simple its a samsung junk 😢

• 
  @GongshowGarage9 ай бұрын

  Great vid my friend

• 
  @Roadhvac9 ай бұрын

  G

• 
  @Roadhvac9 ай бұрын

  Thanks for your comment

• 
  @Steve-um5mm10 ай бұрын

  Why does restricting air flow make the fan speed up?

• 
  @Roadhvac9 ай бұрын

  This is a direct drive motor out of a furnace that is figured for heat exchanger restrictions. Unlike Pulley driven motors. Direct drive motors need back pressure in order to run at its desired amp rating.

• 
  @petejohnson83978 ай бұрын

  it is counterintuitive, but the power used is a function of the amount of air moved. take a shop vac or regular vacuum and block the intake with your hand. listen to the motor spin faster. no air movement. no or less work being done so less load on the motor.

• 
  @Steve-um5mm8 ай бұрын

  Thanks for the info, learn something every day!

• 
  @achdiagnostic77738 ай бұрын

  It's all about load. The motor is going slower because of load. When you restrict the flow the load decreases causing the motor to run at a higher rpm. CFM is not really increasing but velocity is.

• 
  @ryholli521710 ай бұрын

  Promo SM

• 
  @EthanHurley-ky4hi11 ай бұрын

  What do you mean you heard the furnace kick on when the heat was set too 70 and it was 73 in the house

• 
  @Roadhvac11 ай бұрын

  I'm not sure why, but the vent motor kicked on then shut right back down. I never mentioned that, but good eye on your part.

• 
  @mikecamalier265311 ай бұрын

  Always take the spark plug wire off.

• 
  @Dorado199711 ай бұрын

  Good video, I like how you include where all the bolts are. Nice Toro for sure!

• 
  @Roadhvac11 ай бұрын

  Thanks for your comment. Well, when I watch other videos, they seem to leave out some critical things if you have never done anything like this. Or if you're not mechanically inclined.

• 
  @JakeAndBeastBoy200211 ай бұрын

  Just like a hurricane

• 
  @undaya Жыл бұрын

  i removed and cleaned at car wash.

• 
  @Roadhvac11 ай бұрын

  That sounds great. Just make sure to dry out the motor well before you power it up.

• 
  @Geminiappleboy Жыл бұрын

  This was amazing! Thank you!

• 
  @Roadhvac11 ай бұрын

  Glad it was helpful!

• 
  @FBGCHANNEL Жыл бұрын

  I have a 4 ton blower from an amana furnace set up and she works good

• 
  @Roadhvac11 ай бұрын

  I'm sure that's pushing a lot of air.

• 
  @Blacks4Trump2024 Жыл бұрын

  Doing gods work

• 
  @stanmatej35 Жыл бұрын

  Samsung refrigerators ... boycott buying them ! and any other samsung products . $ money talks .

• 
  @Roadhvac Жыл бұрын

  Only reason I bought this one was because it was only 250.00. I normally wouldn't purchase Samsung.

• 
  @erniewurtz243 Жыл бұрын

  Your pretty good

• 
  @Roadhvac Жыл бұрын

  I'm trying to keep it going.

• 
  @tristanwwsd Жыл бұрын

  Did this work?

• 
  @jorgegalo6982 Жыл бұрын

  😅❤

• 
  @Roadhvac Жыл бұрын

  Well, so far, but I was out of town, and my wife said she heard the fan making a little noise again. I may have to add an extra heater, which is what I'm hearing some people have had to do.

• 
  @Roadhvac Жыл бұрын

  I'm going to check and make sure my heater is working first.

• 
  @tristanwwsd Жыл бұрын

  @@Roadhvac 👍

• 
  @carl6626 Жыл бұрын

  Did you melt off the ice?

• 
  @stellingfan Жыл бұрын

  I still use a 682 as my only mower. Not made like this any more, way too complicated

• 
  @Roadhvac Жыл бұрын

  I was lucky and just found one for 200.00. The guy was tired of working on it. Well, come to find out the starter was just stuck. Critters had built a nest. Great shape.

• 
  @squirrellyadventures2809 Жыл бұрын

  Hey what is the belt length that connects the pto to the mow deck I just picked a 1282 up yesterday and I'm having trouble finding info on it

• 
  @Roadhvac Жыл бұрын

  Try 1/2" X 69 Try Tractor Supply. If it is wrong, you will be able to exchange it. That's the size my research comes up with. All I had to replace was the deck belt . If I remember right, it was a 77". Hope this helps.

• 
  @vanover69 Жыл бұрын

  great video, I have a question on removing a jet. Im trying to remove a 2" waterway jet. I turned it counter clockwise until it shut off and then a bit more. it will not come off. I tried on the jet next to it and it came off. I twisted the jet back to the right and then to the left and its really tight and will not come off. Any thoughts?

• 
  @Roadhvac Жыл бұрын

  Can you reach both sides at the same time, hold one, and turn the other one counter clockwise . If I could see it, it would help more. If you did one of the same size it should work the same. Best of luck. Take your time and take a good look at it. You can do it.