You guys ride a harley and you need $100 toolkit to install $2 o-rings?😂 wtf takes a 1/4 socket and cpl paper clips......
@theburningredbeacon96252 ай бұрын
I thought the system had to be purged before disconnecting pressured fuel line.
@larrywhitworth55692 ай бұрын
You are turning the tool counterclockwise in the video on both upper and lower as well.
@rich15446 ай бұрын
Where do you buy the kit at?
@Vtwin608 ай бұрын
Thanks for selling us on tooling and not for actually showing us what to do.
@remyr57499 ай бұрын
He did not insert the tool in all the way like the instructions say; which leads me to believe he just put the o-rings in there loosely as a demo of what to do. Also assuming the gas tank was empty because when I did mine, it dumped 5 gallons of gas all over my garage floor. At that point, I just removed the entire check valve assembly from the tank to make the rebuild easier. The tool was unsuccessful at removing the 1st o-ring completely and the WD-40 I sprayed in there at the beginning of my process just left the remaining bit to just rotate in it's seat with no way to remove it. The paper clip wouldn't do the trick. Wasted $ on the tool, wasted time, wasted gas, funkified my garage, ruined my shoes. This should have been a recall in my opinion. My FLHR has less than 10k miles on it. I'm seeing complete check-valves for sale online for around $34. Lesson learned.
@robertbodkin90579 ай бұрын
Thank you for the demonstration great job on everything . Very well detailed
@ddvutg11 ай бұрын
Nice video dude. To think I almost paid Harley $800 to do this along with an inspection and replace the front brake switch.
@jerielyork439911 ай бұрын
Where do I buy it from
@indianbill31232 ай бұрын
Amazon…but get the MC500
@josepeixoto338411 ай бұрын
that's nuts.... who comes up with convoluted shite like that? --stupid inventions like that should be illegal, at least stay clear of..
@amyfurr56311 ай бұрын
I have a 2008 Dyna Street Bob. Will this work on it? If so, where do I get the tool for it? Thank you for your help.
@Nationalpdinc11 ай бұрын
Harley Davidson store made me by the hoses for $400😢
@vlvtrabbit11 ай бұрын
Why not remove the damn thing, replace it at your table & install???
@former_member Жыл бұрын
An uneeded expensive gimmick that is NOT required to do the job, Order MC300 and use a motorcycyle lift so its easier to access. A seal pick and manual dexterity are all that is needed.
@drolnady Жыл бұрын
Tool didn't work for me, o-rings were brittle. Video by 'Biker Babe Beth' helped me get job done.
@ballstud2007 Жыл бұрын
How do you rebuild the line side?
@drolnady Жыл бұрын
I used a pick to get the old o-ring out, small flat blade to seat the new one.
@chavalee2146 Жыл бұрын
Where can I find the tool kit
@kkc3009 Жыл бұрын
Yeah but I how do I put my own hose on it so that I don't have to pay $65 extra dollars for a foot of hose on the mc800? How come the internet searches only yield fuel pressure testing kits for automotive applications only? I don't see how they cross over so far because I had an extension auto fuel pressure testing kit and none of the pieces could be configured to test the fuel pressure of an EFI HD
@nicksterguy1 Жыл бұрын
WARNING: if attempting on a sportster drain your tank first as a sportster does not have a tube and you will have gas coming out even if the system isn’t pressurized. Also, order extra viton rings as they are extremely fragile and will bind then break very easily.
@Blkbeard420 Жыл бұрын
Or just drain the gas normal?
@arturohernandez8852 Жыл бұрын
thanks for sharing your video. I tried it the third time I did. I am satisfied.
@pipesandtwowheels Жыл бұрын
Thanks for this.
@victorhernandez8765 Жыл бұрын
Thank You!
@arturohernandez8852 Жыл бұрын
You must have 3 sets or more. it may not work well on the first try.
@arturohernandez8852 Жыл бұрын
before installing the new ones. activates the fuel pump to clean particles
@arturohernandez8852 Жыл бұрын
I already tried it but it keeps crawling much more.
@petersantana9899 Жыл бұрын
Do you need to remove all the gas from the tank?
@GurthRacing Жыл бұрын
do these tools work on Iron 883?
@hugavet3049 Жыл бұрын
Why not just replace the entire check valve assembly?
@mikewhited4745 Жыл бұрын
Do you need to remove all the gas out of the tank?
@slowpoke96Z28 Жыл бұрын
Fuck that carrying pouch lol.
@tomdunn2583 Жыл бұрын
you are rotating COUNTER clockwise what up w/that?
@p_rad7551 Жыл бұрын
This tutorial and the tools involved are garbage. Dont fall for this scam.
@dipper7273 Жыл бұрын
Huge tip Make sure all the O-ring comes out. My O-ring was absolutely brittle and came out in 10 to 15 chunks. I had one small chunk left on the bottom O-ring and I couldn’t get the new O-ring seated until that chunk fell out! Good luck that bottom O-ring is a BITCH Great basic video
@eddiebewley3954 Жыл бұрын
Bought the tool for $100. The ORings with any age shred when you use it. I replaced the Check Valve, Regulator, fuel filter for $70. Bike wouldn't start once all the ORings were replaced. Unfortuately, the shredded ORing has traveled down into the fuel Injectors and bike didn't start. It takes 15 minutes to replace the parts using Harley original parts. I'm 6 hours and the bike still doesn't start.
@fulviocervai7390 Жыл бұрын
Ciao volevo chiederti, devo svuotare il serbatoio prima di fare il lavoro di sostituizione oring? Grazie Fulvio
@fulviocervai7390 Жыл бұрын
Ti sembra strano ma non si capisce se il serbatoio è vuoto…. ?
@philstercula6161 Жыл бұрын
Where does one get the tools and o'rings for a 2001 FLTRI. My local dealership said couldn't help and don't work on HD touring earlier than 2013, believe that. Either do local non dealership HD repair shops.
@dr.mikedaydccme4606 Жыл бұрын
If I could give you 50 likes I would for this video. Awesome.
@zman59302 жыл бұрын
I don’t know but I thought you had to purge the system before removing the fuel line?
@richardbarnard66862 жыл бұрын
I just purchased and used this tool set, and yes the 19 year old lower O-ring was brittle it came out in half, but the tool kit did come with a thin little instrument to remove any broken off bits of O-ring that were still in the Grove that worked great, the O-rings that came in the rebuild kit fit perfect in my 2003 Duece, no more leak. Thank you
@GreekoCanuck2 жыл бұрын
Where did you get the tools and kit? If you dont mind me asking
@richardbarnard66862 жыл бұрын
@@GreekoCanuck I ordered it from Amazon along with the O-rings.
@GreekoCanuck2 жыл бұрын
@@richardbarnard6686 I looked and couldn't find it, what are the chances you have the link for it?
@@richardbarnard6686how did you get the bottom O-ring? It seems like it's too big.
@Steve-pu3di2 жыл бұрын
Bullshit
@EkimRrac2 жыл бұрын
Worked on the upper not the lower tool sucks. Fuel tool is selling a defective lower o ring with there rebuild kit, the lower o ring you need to buy is 14mm10mm2mm. Even the dealer didn't know that fuel tool has a defective o ring in there kit, the dealer will only change the check valve.
@kellywhittington70332 жыл бұрын
This tool was a huge help. I did feel that the 2nd hook for tool B wasn't as long as what is shown in the video, but it finally did the trick. Getting the smaller o-ring into the tool correctly to put the check valve components back in took a bit of doing, but once I figured that out, it went easily. Thanks for the video, couldn't have figured it out otherwise.
@harleycharlie8510 ай бұрын
What size bottom o-ring? Mine keeps coming out and seems a bit large.
@jamesbronson33472 жыл бұрын
How did you drain the fuel out of the tank?
@dr.mikedaydccme4606 Жыл бұрын
I always use a syphon pump I got from autozone that you pump until the fuel starts going through it and it continues on its own. Go in through the gas cap opening. Then tilt the tank up from the rear a bit to work easier at the o-rings.
@Loud_Pipes_Cycles2 жыл бұрын
Hi where can you buy it?
@bartvn95932 жыл бұрын
Hi, what model is this? Have a 2008 Heritage Softail Classic here, just started leaking gas and looks like this is the problem...
@Jurnymn2 жыл бұрын
About a min in all audio stopped.
@NoooBama2 жыл бұрын
This guy makes it look a lot easier than it was for me. I guess it's easier if you do as maintenance in stead of waiting for your check valve to start leaking. It was not easy for me because my O-rings were practically disintegrated so it was a lot tougher to get the old rings out. I eventually got it done, thanks.
@tomdunn2583 Жыл бұрын
Spend the 40 bucks next time and just get a NEW valve. MUCH easier and it is FIXED
@NoooBama Жыл бұрын
@@tomdunn2583 got it done , it just wasn't as easy, but thanks for playing.
@harleycharlie8510 ай бұрын
@NoooBama how did you get the bottom o-ring on? It seems like the o-ring is too big. I have this kit to install all the rings but the bottom isn't working. Any help is appreciated please thank you.
@kd83092 жыл бұрын
Great video!! Thank you very much!
@toolman4653 жыл бұрын
awesome video....literally took my about 2 minutes to do this and I have NO mechanical expertise whatsoever. Great Tool and Great Video....thanks!!!
Пікірлер
You guys ride a harley and you need $100 toolkit to install $2 o-rings?😂 wtf takes a 1/4 socket and cpl paper clips......
I thought the system had to be purged before disconnecting pressured fuel line.
You are turning the tool counterclockwise in the video on both upper and lower as well.
Where do you buy the kit at?
Thanks for selling us on tooling and not for actually showing us what to do.
He did not insert the tool in all the way like the instructions say; which leads me to believe he just put the o-rings in there loosely as a demo of what to do. Also assuming the gas tank was empty because when I did mine, it dumped 5 gallons of gas all over my garage floor. At that point, I just removed the entire check valve assembly from the tank to make the rebuild easier. The tool was unsuccessful at removing the 1st o-ring completely and the WD-40 I sprayed in there at the beginning of my process just left the remaining bit to just rotate in it's seat with no way to remove it. The paper clip wouldn't do the trick. Wasted $ on the tool, wasted time, wasted gas, funkified my garage, ruined my shoes. This should have been a recall in my opinion. My FLHR has less than 10k miles on it. I'm seeing complete check-valves for sale online for around $34. Lesson learned.
Thank you for the demonstration great job on everything . Very well detailed
Nice video dude. To think I almost paid Harley $800 to do this along with an inspection and replace the front brake switch.
Where do I buy it from
Amazon…but get the MC500
that's nuts.... who comes up with convoluted shite like that? --stupid inventions like that should be illegal, at least stay clear of..
I have a 2008 Dyna Street Bob. Will this work on it? If so, where do I get the tool for it? Thank you for your help.
Harley Davidson store made me by the hoses for $400😢
Why not remove the damn thing, replace it at your table & install???
An uneeded expensive gimmick that is NOT required to do the job, Order MC300 and use a motorcycyle lift so its easier to access. A seal pick and manual dexterity are all that is needed.
Tool didn't work for me, o-rings were brittle. Video by 'Biker Babe Beth' helped me get job done.
How do you rebuild the line side?
I used a pick to get the old o-ring out, small flat blade to seat the new one.
Where can I find the tool kit
Yeah but I how do I put my own hose on it so that I don't have to pay $65 extra dollars for a foot of hose on the mc800? How come the internet searches only yield fuel pressure testing kits for automotive applications only? I don't see how they cross over so far because I had an extension auto fuel pressure testing kit and none of the pieces could be configured to test the fuel pressure of an EFI HD
WARNING: if attempting on a sportster drain your tank first as a sportster does not have a tube and you will have gas coming out even if the system isn’t pressurized. Also, order extra viton rings as they are extremely fragile and will bind then break very easily.
Or just drain the gas normal?
thanks for sharing your video. I tried it the third time I did. I am satisfied.
Thanks for this.
Thank You!
You must have 3 sets or more. it may not work well on the first try.
before installing the new ones. activates the fuel pump to clean particles
I already tried it but it keeps crawling much more.
Do you need to remove all the gas from the tank?
do these tools work on Iron 883?
Why not just replace the entire check valve assembly?
Do you need to remove all the gas out of the tank?
Fuck that carrying pouch lol.
you are rotating COUNTER clockwise what up w/that?
This tutorial and the tools involved are garbage. Dont fall for this scam.
Huge tip Make sure all the O-ring comes out. My O-ring was absolutely brittle and came out in 10 to 15 chunks. I had one small chunk left on the bottom O-ring and I couldn’t get the new O-ring seated until that chunk fell out! Good luck that bottom O-ring is a BITCH Great basic video
Bought the tool for $100. The ORings with any age shred when you use it. I replaced the Check Valve, Regulator, fuel filter for $70. Bike wouldn't start once all the ORings were replaced. Unfortuately, the shredded ORing has traveled down into the fuel Injectors and bike didn't start. It takes 15 minutes to replace the parts using Harley original parts. I'm 6 hours and the bike still doesn't start.
Ciao volevo chiederti, devo svuotare il serbatoio prima di fare il lavoro di sostituizione oring? Grazie Fulvio
Ti sembra strano ma non si capisce se il serbatoio è vuoto…. ?
Where does one get the tools and o'rings for a 2001 FLTRI. My local dealership said couldn't help and don't work on HD touring earlier than 2013, believe that. Either do local non dealership HD repair shops.
If I could give you 50 likes I would for this video. Awesome.
I don’t know but I thought you had to purge the system before removing the fuel line?
I just purchased and used this tool set, and yes the 19 year old lower O-ring was brittle it came out in half, but the tool kit did come with a thin little instrument to remove any broken off bits of O-ring that were still in the Grove that worked great, the O-rings that came in the rebuild kit fit perfect in my 2003 Duece, no more leak. Thank you
Where did you get the tools and kit? If you dont mind me asking
@@GreekoCanuck I ordered it from Amazon along with the O-rings.
@@richardbarnard6686 I looked and couldn't find it, what are the chances you have the link for it?
@@GreekoCanuck it's fuel-tool check valve repair tools MC-400
@@richardbarnard6686how did you get the bottom O-ring? It seems like it's too big.
Bullshit
Worked on the upper not the lower tool sucks. Fuel tool is selling a defective lower o ring with there rebuild kit, the lower o ring you need to buy is 14mm10mm2mm. Even the dealer didn't know that fuel tool has a defective o ring in there kit, the dealer will only change the check valve.
This tool was a huge help. I did feel that the 2nd hook for tool B wasn't as long as what is shown in the video, but it finally did the trick. Getting the smaller o-ring into the tool correctly to put the check valve components back in took a bit of doing, but once I figured that out, it went easily. Thanks for the video, couldn't have figured it out otherwise.
What size bottom o-ring? Mine keeps coming out and seems a bit large.
How did you drain the fuel out of the tank?
I always use a syphon pump I got from autozone that you pump until the fuel starts going through it and it continues on its own. Go in through the gas cap opening. Then tilt the tank up from the rear a bit to work easier at the o-rings.
Hi where can you buy it?
Hi, what model is this? Have a 2008 Heritage Softail Classic here, just started leaking gas and looks like this is the problem...
About a min in all audio stopped.
This guy makes it look a lot easier than it was for me. I guess it's easier if you do as maintenance in stead of waiting for your check valve to start leaking. It was not easy for me because my O-rings were practically disintegrated so it was a lot tougher to get the old rings out. I eventually got it done, thanks.
Spend the 40 bucks next time and just get a NEW valve. MUCH easier and it is FIXED
@@tomdunn2583 got it done , it just wasn't as easy, but thanks for playing.
@NoooBama how did you get the bottom o-ring on? It seems like the o-ring is too big. I have this kit to install all the rings but the bottom isn't working. Any help is appreciated please thank you.
Great video!! Thank you very much!
awesome video....literally took my about 2 minutes to do this and I have NO mechanical expertise whatsoever. Great Tool and Great Video....thanks!!!