great video!!! Nice burnout!! Built in America for the WIN! God bless you guys... IS AIRDOG quieter than FASS??? I heard that is so... I want quiet.
@ajo20127 күн бұрын
What do you do with the old feed line? Do you just leave the end open?
@martinstanley33737 күн бұрын
So in a stock situation where the injectors don’t require that much fuel, how does the return trickle of fuel work? Where is all the extra unused fuel going? The pump supplies a large volume of fuel doesn’t it?
@AirDogSales6 күн бұрын
It recirculates back to the suction side of the pump though the fuel pressure regulator.
@aladin45416 күн бұрын
HERMOSA!
@aladin45416 күн бұрын
se ve muy bonita, que medida de llantas traes?
@maxswell420820 күн бұрын
I’m finally getting around to installing my airdog on my 2nd gen BECAUSE my brake line that runs along fuel line rusted out, that being said that line looks crusty on that pretty truck . Also, wouldn’t it be beneficial to have the pump mounted as close to the tank as possible?
@dartgts383Ай бұрын
Love this truck , I have an extra 24v ... hhhhhmmmmmm
@tomaskey6844Ай бұрын
About to buy a 2006 2500 express van with the 6.6 Duramax. After much consideration I am leaning towards the AirDog over the FASS system. Cant give an exact reason though. Both seem to be good products.
@korn111685Ай бұрын
Nice build. Factory gas gauge cluster? I’m hoping to use my gas gauges. I have low mile 24v, same miles as the gas truck.
@hakrx1Ай бұрын
Airdog: Tells you you can use the competition's filters. FASS: Tells you everyone elses product is inferior.
@aaronkelley8909Ай бұрын
I put 100k miles on an old Airdog. I sold the truck but it's still running strong.
@RicardoGarcia-sz9lo2 ай бұрын
If this model wears out is it ok to just replace the pump itself
@mavericksanders55122 ай бұрын
Do yall still sell motor replacements? My shaft seal failed causing fuel to get into motor and shorting it out.
@larrypeachy23912 ай бұрын
How does the edge comp perform for a truck that tows a lot ?
@Hunterrnorris2 ай бұрын
I actually thought those were 420s, you had me fooled haha, clean set up
@kengood68852 ай бұрын
What head unit is that
@schmbrt962 ай бұрын
Joying android radio
@paveltolz66012 ай бұрын
Customer Service is Top Notch. I received the DF-165 with the motor I bought from a good friend. I guess it was manufactured around 2008 and it ran on another truck previous to the owner I got it from. It had sat on shelves between owners and I installed it on my truck in 2013. In 2017 the pump motor failed and I was able to get a replacement at a reduced cost. The support tech pulled up the serial number and we confirmed the original owner (friend of mine too). I waited to install it back into the system having other issues to address but, it's back in now and the truck is much happier.
@Rumple4skinny2 ай бұрын
Installed mine yesterday, and it hums so loud. not sure what the heck is causing it. The connections are good and it's definitely pushing diesel, but its way louder than it should be. If I touch the hoses or the fuel tank, i can feel vibration.
@AirDogSales2 ай бұрын
Call our tech department at 317-421-3180 and they will run through some troubleshooting steps with you.
@jeremylabrecque42502 ай бұрын
Can I use a glow shift guage
@benitocamela85412 ай бұрын
Can you install a fuel gauge further up where the primer on the oem fuel filter is? Deleted the primer because it was leaking and the blocker plate comes with a pre drilled hole for a fuel pressure gauge. Will it give the same readings as if it was installed in the lift pump?
@jeremylabrecque42502 ай бұрын
My fuse doesn’t seem to stay
@WeekleyRehabFishingCharters3 ай бұрын
Love how easy the install was, did in my driveway took no time at all. Great product
@SteelBlueCorvette3 ай бұрын
I can still hear that rear brake line behind the tank screaming to be replaced…
@trevormcclain24483 ай бұрын
Where do I get the different springs for my different psi
@whiskeytango97693 ай бұрын
I have a 2010 duramax LMM. I just installed the AirDog II 165 5G a week ago. I noticed that if I started the truck immediately after the glowplug light goes out, no problem. If I let the pump run 30 seconds or a minute [I did that checking for leaks] then start the truck, it cranked over for a few seconds before firing. It ran just fine though. Today I put a pressure gauge on the airdog and found it was set for 7 PSI. I turned it down to 5.5 PSI, took it for a drive and checked again engine running. Setting was stable at 6 PSI with truck idling. Starts and runs great.
@abc123hshdhd8w3 ай бұрын
What kind of transmission is that?
@RK-be1op3 ай бұрын
Fass is a joke. They told me I needed to send them my entire pump for a refund since it can’t make more than 12psi. They didn’t refund me and just sent it back after they held onto it for almost two weeks. Horrible customer service. They’ve blocked me from contacting them. I wish I would of bought a Airdog, then I wouldn’t have to deal with the liars from the other company
@dirtymiketheboys94983 ай бұрын
Can i use an Airdog II 165 on a stock 6.7?
@duramax20794 ай бұрын
i love airdog
@BiggusDickus24 ай бұрын
You don't have to use that filter for the fuel water separator. You can get one with a drain on it
@Ry_Guy4 ай бұрын
Looks great, besides for the hideous bumper and it's misalignment! 🥴
@xcrapprentice57974 ай бұрын
Is There any benefit to hooking the oem fuel cooler up in series with the return line? Just curious
@AirDogSales4 ай бұрын
The AirDog II pumps don't return enough fuel for that to be beneficial.
@ruthless68704 ай бұрын
If I have a fuel pressure regulator would I just be able to read it off that or still put one on the pump?
@AirDogSales4 ай бұрын
At the fuel pressure regulator will work just fine. Reading pressure anywhere on the pressure side of the pump will give you an accurate reading.
@100pyatt4 ай бұрын
Do you make a product for the F-150 Powerstroke diesel ?
@brodiejacobs51674 ай бұрын
Please someone answer me does it still have the 1500 axle Dana 60?? I’m doing the swap want to know if it will handle torque
@AirDogSales4 ай бұрын
It has the stock Chrysler 9.25 rear with a Yukon dura-grip limited slip. It it plenty strong.
@reysandwich4 ай бұрын
Those columns Where do I get some?
@cobieblack65584 ай бұрын
So question for you. On my 02 manual truck, what is needed to turn 4k rpm? Springs, push rods, injectors of course. But on the rev limiter side what will allow it to fuel that far?
@5.9media4 ай бұрын
Get a quadzlla tuner and set the limiter to 3600 and let her eat
@ryanmcmillan71964 ай бұрын
What program edge ?
@davidbartlett10275 ай бұрын
Does this kit work if the lift pump is on the block?
@LucasisforOil5 ай бұрын
Hooked up my air dog and it seems to be barely sucking. What gives?
@LucasisforOil5 ай бұрын
Same install for dual tank trucks?
@Duckis845 ай бұрын
Was the driveshaft removed to do this?
@victorsidingguy43715 ай бұрын
Hello what pressure should I put on my bomb for lb7 2003?
@victorsidingguy43715 ай бұрын
Hello how much pressure do I put on my bomb for lb7 2003?
@AirDogSales5 ай бұрын
8-10 psi
@victorsidingguy43714 ай бұрын
I only got it to 15. You got a good trick for me to get it lower?
@aaronschocke21472 ай бұрын
You are at 15 with the screw all the way backed out?? What truck do you have?
@victorsidingguy43715 ай бұрын
Hello, how much pressure do I put on the lb7 2003 pump?
@AirDogSales5 ай бұрын
8-10 psi
@ericblakeney87765 ай бұрын
Good video thank you for sharing. But i wish I had that style fuel line clamps on my truck
@kalebstout76735 ай бұрын
Man I’ve watched this video like 5 times and still have questions. I’m installing a AirDog 5G 220gph on my 97 dodge ram 2500 12v Cummins with a dual sump from Ohio diesel. I’m running a block off plate on the mechanical lift pump port and deleted the stock fuel filter and removed the stock hard fuel lines. Curious what I do with the hard line where the overflow valve goes. I have a Tork Tek 70psi race overflow valve I’m installing to replace the adjustable one. Also do I need to use the filler neck adapter when using a sump? And should there be an oring or gas Teflon tape on the fitting that goes into the banjo fitting on the pump!
@AirDogSales5 ай бұрын
If you are replacing the return line off of the p-pump you will still need to tee the injector return into the return line. The injector return needs to be downstream of the overflow valve. If you have a feed and return sump, you won't need to use the filler neck tee. No, no tape or sealant on the fittings. The sealing washer provided in the kit does all the sealing.
@kalebstout76735 ай бұрын
@@AirDogSales thank you so very much!
@sled77825 ай бұрын
I’ve replaced my filters about 6-8 times over the years. The new Air Dog brand filters I purchased has a new style petcock
@Slingshot2775 ай бұрын
Canadian here. I wondered if it holding the water at the filter would plug up faster than normal because it’s not aloud to drain or settle down during the filtering process. Once the fuel freezes at the filter I’d assume it would just freeze the filter up and plug faster. Baldwin all the way.
Пікірлер
great video!!! Nice burnout!! Built in America for the WIN! God bless you guys... IS AIRDOG quieter than FASS??? I heard that is so... I want quiet.
What do you do with the old feed line? Do you just leave the end open?
So in a stock situation where the injectors don’t require that much fuel, how does the return trickle of fuel work? Where is all the extra unused fuel going? The pump supplies a large volume of fuel doesn’t it?
It recirculates back to the suction side of the pump though the fuel pressure regulator.
HERMOSA!
se ve muy bonita, que medida de llantas traes?
I’m finally getting around to installing my airdog on my 2nd gen BECAUSE my brake line that runs along fuel line rusted out, that being said that line looks crusty on that pretty truck . Also, wouldn’t it be beneficial to have the pump mounted as close to the tank as possible?
Love this truck , I have an extra 24v ... hhhhhmmmmmm
About to buy a 2006 2500 express van with the 6.6 Duramax. After much consideration I am leaning towards the AirDog over the FASS system. Cant give an exact reason though. Both seem to be good products.
Nice build. Factory gas gauge cluster? I’m hoping to use my gas gauges. I have low mile 24v, same miles as the gas truck.
Airdog: Tells you you can use the competition's filters. FASS: Tells you everyone elses product is inferior.
I put 100k miles on an old Airdog. I sold the truck but it's still running strong.
If this model wears out is it ok to just replace the pump itself
Do yall still sell motor replacements? My shaft seal failed causing fuel to get into motor and shorting it out.
How does the edge comp perform for a truck that tows a lot ?
I actually thought those were 420s, you had me fooled haha, clean set up
What head unit is that
Joying android radio
Customer Service is Top Notch. I received the DF-165 with the motor I bought from a good friend. I guess it was manufactured around 2008 and it ran on another truck previous to the owner I got it from. It had sat on shelves between owners and I installed it on my truck in 2013. In 2017 the pump motor failed and I was able to get a replacement at a reduced cost. The support tech pulled up the serial number and we confirmed the original owner (friend of mine too). I waited to install it back into the system having other issues to address but, it's back in now and the truck is much happier.
Installed mine yesterday, and it hums so loud. not sure what the heck is causing it. The connections are good and it's definitely pushing diesel, but its way louder than it should be. If I touch the hoses or the fuel tank, i can feel vibration.
Call our tech department at 317-421-3180 and they will run through some troubleshooting steps with you.
Can I use a glow shift guage
Can you install a fuel gauge further up where the primer on the oem fuel filter is? Deleted the primer because it was leaking and the blocker plate comes with a pre drilled hole for a fuel pressure gauge. Will it give the same readings as if it was installed in the lift pump?
My fuse doesn’t seem to stay
Love how easy the install was, did in my driveway took no time at all. Great product
I can still hear that rear brake line behind the tank screaming to be replaced…
Where do I get the different springs for my different psi
I have a 2010 duramax LMM. I just installed the AirDog II 165 5G a week ago. I noticed that if I started the truck immediately after the glowplug light goes out, no problem. If I let the pump run 30 seconds or a minute [I did that checking for leaks] then start the truck, it cranked over for a few seconds before firing. It ran just fine though. Today I put a pressure gauge on the airdog and found it was set for 7 PSI. I turned it down to 5.5 PSI, took it for a drive and checked again engine running. Setting was stable at 6 PSI with truck idling. Starts and runs great.
What kind of transmission is that?
Fass is a joke. They told me I needed to send them my entire pump for a refund since it can’t make more than 12psi. They didn’t refund me and just sent it back after they held onto it for almost two weeks. Horrible customer service. They’ve blocked me from contacting them. I wish I would of bought a Airdog, then I wouldn’t have to deal with the liars from the other company
Can i use an Airdog II 165 on a stock 6.7?
i love airdog
You don't have to use that filter for the fuel water separator. You can get one with a drain on it
Looks great, besides for the hideous bumper and it's misalignment! 🥴
Is There any benefit to hooking the oem fuel cooler up in series with the return line? Just curious
The AirDog II pumps don't return enough fuel for that to be beneficial.
If I have a fuel pressure regulator would I just be able to read it off that or still put one on the pump?
At the fuel pressure regulator will work just fine. Reading pressure anywhere on the pressure side of the pump will give you an accurate reading.
Do you make a product for the F-150 Powerstroke diesel ?
Please someone answer me does it still have the 1500 axle Dana 60?? I’m doing the swap want to know if it will handle torque
It has the stock Chrysler 9.25 rear with a Yukon dura-grip limited slip. It it plenty strong.
Those columns Where do I get some?
So question for you. On my 02 manual truck, what is needed to turn 4k rpm? Springs, push rods, injectors of course. But on the rev limiter side what will allow it to fuel that far?
Get a quadzlla tuner and set the limiter to 3600 and let her eat
What program edge ?
Does this kit work if the lift pump is on the block?
Hooked up my air dog and it seems to be barely sucking. What gives?
Same install for dual tank trucks?
Was the driveshaft removed to do this?
Hello what pressure should I put on my bomb for lb7 2003?
Hello how much pressure do I put on my bomb for lb7 2003?
8-10 psi
I only got it to 15. You got a good trick for me to get it lower?
You are at 15 with the screw all the way backed out?? What truck do you have?
Hello, how much pressure do I put on the lb7 2003 pump?
8-10 psi
Good video thank you for sharing. But i wish I had that style fuel line clamps on my truck
Man I’ve watched this video like 5 times and still have questions. I’m installing a AirDog 5G 220gph on my 97 dodge ram 2500 12v Cummins with a dual sump from Ohio diesel. I’m running a block off plate on the mechanical lift pump port and deleted the stock fuel filter and removed the stock hard fuel lines. Curious what I do with the hard line where the overflow valve goes. I have a Tork Tek 70psi race overflow valve I’m installing to replace the adjustable one. Also do I need to use the filler neck adapter when using a sump? And should there be an oring or gas Teflon tape on the fitting that goes into the banjo fitting on the pump!
If you are replacing the return line off of the p-pump you will still need to tee the injector return into the return line. The injector return needs to be downstream of the overflow valve. If you have a feed and return sump, you won't need to use the filler neck tee. No, no tape or sealant on the fittings. The sealing washer provided in the kit does all the sealing.
@@AirDogSales thank you so very much!
I’ve replaced my filters about 6-8 times over the years. The new Air Dog brand filters I purchased has a new style petcock
Canadian here. I wondered if it holding the water at the filter would plug up faster than normal because it’s not aloud to drain or settle down during the filtering process. Once the fuel freezes at the filter I’d assume it would just freeze the filter up and plug faster. Baldwin all the way.
music is gay rather hear the truck....