Пікірлер

• 
  @nevadarobert79089 сағат бұрын

  Sorry to hear what happened. Flatbed it to a shop. Tell them what happened. Don’t run it.

• 
  @nevadarobert790820 сағат бұрын

  Many experts would agree with your plan.

• 
  @JUMBOs-RCКүн бұрын

  I got a LS430 with 175k and no transmission maintenance done... I'm gonna just leave it alone

• 
  @nevadarobert7908Күн бұрын

  It should. Best of luck!

• 
  @izzy_c10Күн бұрын

  Would this work for a 540i e39

• 
  @nevadarobert7908Күн бұрын

  I have been told that Amsoil sells an equivalent that meets all the GM specifications. Many racers prefer the Amsoil as it runs cooler. Hope this helps

• 
  @abdulrhmanabdulla494Күн бұрын

  Hi just a quick qustion what is the best alternitive to Dexron ULV transmission fluid Thanks

• 
  @nevadarobert79082 күн бұрын

  Good points

• 
  @stlman112 күн бұрын

  Can you make the camera jump anymore. And mic the other guy.

• 
  @JUMBOs-RC2 күн бұрын

  I just reach down from under the hood and reach to access the drain

• 
  @nevadarobert79082 күн бұрын

  I will do it. Thanks

• 
  @cadenfabbricino70396 күн бұрын

  if you know my car shifts hard I wonder if replacing the fluid could fix that

• 
  @nevadarobert79086 күн бұрын

  It won’t hurt. Also reset the transmission. If the transmission is bad, the fluid may not help. How many miles since last fluid change?

• 
  @nevadarobert79086 күн бұрын

  I didn’t know that. Serious waste of money. Thanks for letting me know

• 
  @jasonnett99726 күн бұрын

  I work for a utility. Unfortunately, there are a lot of local and state government permitting requirements that require the use of flaggers, whether the work is actually occurring that day or not. It is such a waste.

• 
  @auctionhawk896612 күн бұрын

  Wow, that thing looks great for 9 years in the midwest!!

• 
  @nevadarobert790812 күн бұрын

  It sure is!

• 
  @nevadarobert790815 күн бұрын

  Change the fluid and filter. Assuming the tranny works well.

• 
  @nevadarobert790815 күн бұрын

  Buy a scanner. It is a necessity. There are some scanners that read that are not a lot of money.

• 
  @mmamdou700715 күн бұрын

  LS 430 2006 I’ve leakage do you advise me to replace filter,gasket and replace whatever lost oil once Then every time i remove the bolt then i drain and replace what i lost with new oil till i find out the oil color looks better, The problem is i don’t have a tool to check the oil temperature Do you advise to switch on the car till it goes to the normal temperature then shift to all gears then remove the bolt to drain extra oil And keep it cold then drain then refill Or i’ve to drive it for sometime then drain and repeat Please help

• 
  @driveinstructordrivingscho823316 күн бұрын

  hi there,,,.,

• 
  @driveinstructordrivingscho823316 күн бұрын

  Can I use this one too? Thanks,,,

• 
  @nevadarobert790816 күн бұрын

  Yes, of course

• 
  @driveinstructordrivingscho823316 күн бұрын

  Hello NevadaRobert,,,can I use this clip in my compilation? Any comment what happened? Thanks

• 
  @nevadarobert790816 күн бұрын

  Yes, of course

• 
  @nevadarobert790818 күн бұрын

  Mine came off with bolt removal. Good luck!

• 
  @riotstarter199218 күн бұрын

  I cant seem to get the snout of the 580 supercharger to come off, is there some extra step with the 580 or is my coupler just stuck...

• 
  @nevadarobert790819 күн бұрын

  I like Honda Civics!

• 
  @1_An_Only_F1RME_62619 күн бұрын

  My 2018 Honda civic lx is like this . I’m making payments on it I got it in 2023

• 
  @noyopacific20 күн бұрын

  Nice job ! Thanks for the video.

• 
  @nevadarobert790819 күн бұрын

  Thanks for watching!

• 
  @nevadarobert790822 күн бұрын

  I bought it on Amazon

• 
  @davecarpenter954822 күн бұрын

  What is the part number for the adapter to fill fluid through stand pipe?

• 
  @nevadarobert790822 күн бұрын

  Transmission Oil Fill Adapter for GM 8L90, DT-51190 . ASIN: B0CW2B2DT3. Generic.

• 
  @davecarpenter954821 күн бұрын

  Why did you get the filter for the 8L90? I thought yours was a 10 speed?

• 
  @nevadarobert790820 күн бұрын

  I got the transmission filter from my local dealer. Identical to the one I removed

• 
  @nevadarobert790823 күн бұрын

  2.5 lNA

• 
  @vlesya23 күн бұрын

  It is 2.5 or 3.6 l engine?

• 
  @nevadarobert790824 күн бұрын

  Most excellent advice. Thank you

• 
  @anthonyhall442725 күн бұрын

  And I've been told that it is copper that is used in the treatment that doesn't mix with the aluminum

• 
  @nevadarobert790824 күн бұрын

  Very interesting. Thanks

• 
  @anthonyhall442725 күн бұрын

  Couple things that you can do to cap over treated. What I prefer to do and cost effective is use lattice strips to create a distance between the aluminum and the treated lumber. Most coil boxes will label not to cover treated lumber. I've been doing siding for over 30+ years and I've never had a issue with using this method

• 
  @MaliqBlerim27 күн бұрын

  Darf ich mal fragen was haben Sie getauscht? Ich habe aktuell das selber Problem ich wäre sehr dankbar wenn Sie zeit finden um eine Antwort zu geben

• 
  @nevadarobert790827 күн бұрын

  I accidentally pulled the hoses behind the oil filter housing. Hope this helps

• 
  @naoko36528 күн бұрын

  Does your dryer turn light on when door is open? Mine won’t 😢

• 
  @nevadarobert790828 күн бұрын

  Mine turns on

• 
  @nevadarobert7908Ай бұрын

  I don’t know the numbers. I bought them at my local lexus dealer

• 
  @Obamas-MoleАй бұрын

  Great video, 4:43 what are the part numbers?

• 
  @cw_zl1Ай бұрын

  Great video. What torque did you use for the filter bolts? I've also heard they need to be replaced but I got everything here except new bolts. Also I noticed, 2020+ models use a different transmission filter. For my 19 ZL1 I got the GM24291343.

• 
  @cw_zl1Ай бұрын

  found it. 5 nm + 128 degrees if someone needs to know.

• 
  @nevadarobert7908Ай бұрын

  That is good to know Thanks

• 
  @mbenz9389Ай бұрын

  Thank you! Is the filling plug easy to remove? No need any extensions? What a beautiful garage and car you have!

• 
  @nevadarobert7908Ай бұрын

  I don’t exactly recall. But it was easy. Take care

• 
  @nevadarobert7908Ай бұрын

  Bummer

• 
  @JeffCook-hs7fsАй бұрын

  I had it, got cyl 1 misfire code. Then progressed with cyl 3 too. Confirmed head gasket leak and replaced head gasket along with intake manifold (old one was ultra nasty) replaced most EGR components but thoroughly cleaned EGR cooler. Also replaced spark plugs. This was at 189k miles. At 205k I have cyl 4 misfiring. Same rough starting symptoms but it also runs rough while driving except it’s smooth at full throttle. Probably injector. Going to swap coils to rule it out quickly. Then looking at replacement of the original injectors.

• 
  @alphadiallo1655Ай бұрын

  A Master @ his craft. Good job

• 
  @nevadarobert7908Ай бұрын

  You are too kind

• 
  @nevadarobert7908Ай бұрын

  You have to level it as I did. Why you might ask? The standpipe is why. I hope this helps.

• 
  @joshwhite9983Ай бұрын

  Thanks for the video. Doing the same myself now.

• 
  @nevadarobert7908Ай бұрын

  You can do it! I rechecked my work since I only got 6 liters out (room temperature 25 C) and only used 6 liters at 77 C when refilling it, not the 8.1 liters everyone says it takes. And I drove it to get Tran temp up to 74C, then required only one brake torque to get to 77 C. Be careful as it can burn you. Not worth it.

• 
  @angellujano03Ай бұрын

  maybe also cycle each gear and stay for a min each and in manual mode up to the highest gear stationary. then try to warm up the fluid

• 
  @nevadarobert7908Ай бұрын

  Worth a try. Brake torquing was not fun. Best of luck. Let me know how it works out. I am Open to any methods.

• 
  @joshwhite9983Ай бұрын

  One of the more confusing things to me is what is considered level. Is it how the car would set on the ground, or level the car itself, or like you did and put a level on the trans pan. All of these are different and are going to change what the fluid level would be. But I think I’m going to go with the way you did it.

• 
  @joshwhite9983Ай бұрын

  @@nevadarobert7908 mine took 6 quarts as well. Initially took out 6 quarts. Put 6 1/2 back in, then drained 16oz. after it reached correct temp.

• 
  @nevadarobert7908Ай бұрын

  I had a friend (builder) tell me to not mix the two. I like the wood on the wood.

• 
  @troyheffernan1261Ай бұрын

  I was told about 10 years ago the chemical used in pressure treated wood was outlawed and it didnt damage aluminum facia. So what's the deal, was that older pressure treated wood or were the people from yellow wood in Alabama lying ? Just asking.

• 
  @mostafaabdalla3199Ай бұрын

  How many later need.

• 
  @pw4721Ай бұрын

  Vanden Plas is the name of coachbuilders who produced bodies for specialist and up-market automobile manufacturers. Latterly the name became a top-end luxury model designation for cars from subsidiaries of British Leyland and the Rover Group, being last used in 2009 to denote the top-luxury version of the Jaguar XJ (X350). The business began in 1870 in Brussels, Belgium, initially making axles later producing horse-drawn carriages. It was founded by Guillaume van den Plas, a blacksmith, and his three sons, Antoine, Henri and Willy, who later set up a branch in Paris. Guillaume's surname is Dutch meaning "from the lake". In 1884 they moved from Brussels to Antwerp. With increased business they opened a branch in Brussels again in 1890. By 1900, they worked with De Dion Bouton, Berlier, Germain and Packard. By 1908 Carrosserie Van den Plas had a workforce of 400 men producing 300 special bodies a year, and that soon increased to over 750.[1] The French branch ceased production in 1934 while the Belgian business was active until 1949.[2] The coachbuilders' name first appeared in the United Kingdom in 1906 when Métallurgique cars were imported with Carrosserie Van den Plas coachwork. The first Vanden Plas company in England was established by Warwick Wright (now Peugeot dealers) in 1913, building bodies under license from Carrosserie Van den Plas Belgium.

• 
  @lexus__luvАй бұрын

  7x12= 84. So is it 7ft/lbs or 8ft/lbs because you said (96in/lbs)?

• 
  @nevadarobert7908Ай бұрын

  Good catch! I had a brain fart. 7 ft/lbs is correct.

• 
  @BfloTankАй бұрын

  Dude SHUT-UP ALREADY!!!!