Ok, yea, i tried this once with Elmer's glue, and well, i didn't work after the 3rd day, but amazingly enough, it was holding while i was doing 90mph in the corners, Then failure in the last mile, 😭
@LuXoR1590Ай бұрын
Better is liquid rubber its flexibile and it will not crack like glue
@sammyhooligan803Ай бұрын
Just curious, what brand? Thanks
@LuXoR1590Ай бұрын
@@sammyhooligan803 I had Bison liquid rubber, but any like that will fix
@sammyhooligan803Ай бұрын
@@LuXoR1590 gotcha. Yea, right now I'm trying to fix a leak either on a smaller overflow hose? From the top of a Ford explorer '05 radiator or a small fracture on that hose mount hook up. If it's that hose, after I remove it and look for deterioration/ breaks in that rubber hose then, that would be simple to replace, but if it's on that plastic outlet area then i might try either JB weld or something similar for hard plastic construction of radiator. I noticed about 20 ounces low in overflow tank by airbox side, and a small flow of coolant fluid draining from the small hose hookup/ outlet. Maybe I can figure it out, 👍
@justinwhite6044 ай бұрын
Super glue and baking soda. Works every time
@tayoni8004 ай бұрын
Can it withstand high pressure?
@tomnapier11085 ай бұрын
tried a similar product on a pin hole on a tractor radiator hose does not work the emergency tape gave a much better result had a dew drop leak re wrapped the hose yet to see if the timy dew drop is gone however still have a new hose to fit
@Professional_Youtube_Commenter5 ай бұрын
pipes like that ususally break when they're really really old and the gazilliont hot/cold cycle takes it toll and perishes the material. a hole will from from the inside, and if you repair that hole, another will appear from elsewhere. the walls of that host are uniformally compromised, do yourself a favour and replace it with a brand new part.
@Irvine7214x6apc7 ай бұрын
How about melting a tie wrap with a soldering iron over the hose's cut itself? Sounds pretty straightforward to me, since it will literally become part of the hose construction itself...
@mikea90147 ай бұрын
It will be hot when it breaks
@romemccants44498 ай бұрын
I need to do this rite now...
@romemccants44498 ай бұрын
How much it and dose it comes in a kit wit the white powder or jus the glue??
@thewoollypig6069 ай бұрын
And then I took the petrol out and drove for 3.14 miles on air for the baby Jesus
@Mike_44 Жыл бұрын
What glue/sealant would you recommend for putting together silicone and a metal pip coming off it?
@thechallenger65522 жыл бұрын
You can also use Baking soda so harden the super glue. Iv never used Jonny weld though so it could be better.
@jyotihanda95092 жыл бұрын
Price
@johnnyweld33282 жыл бұрын
$13-15 depending on where its purchased. Mikeshobby.com has it available online, there's a problem with Amazon that were still trying to figure out
@jyotihanda95092 жыл бұрын
Price
@brooksrodrigue69082 жыл бұрын
Crazy question could you use gorilla glue
@johnnyweld33282 жыл бұрын
It does make gorilla glue dry about 2x as fast as normal and makes it harder. But your still looking at hours for it to cure
@brissbeatsentertainment40492 жыл бұрын
hey, does this works with the radiator coolant reservoir?
@robsem12 жыл бұрын
Whenever I got a coolant hose leak I find that the simplest cheapest and easiest way to permanently fix it without having to spend sometimes even a $100 for new hose assemblies, is instead a 5 dollar fix: welcome to a simple hose coupling. It costs about 5 bucks and comes with two clamps and u can get one for about any size. What I do is simply cut the hose in half with a razor where the leak is, insert the coupling between the cut, clamp em back up and there ya have it , good as new, no tape, no worrying about it coming off because this is exactly the method the factory uses at the end of the hose, you're just doing it in middle. Good luck! Was surprised not to see anyone on KZread mention this 🤔 Ps: if ur stuck on the side of the road the easiest way to get back home would be taping up the leak with whatever tape u can get ur hands on (many rounds, use the whole roll if yall have to!) and if u have no tape just wrap a towel or cloth as tight as u can and then just loosen the coolant cap enough for some air to get out so u release the pressure on that tape or cloth. Then fill up reservoir with water if u have no coolant. (Make sure u don't leave that water in during the winter as it'll freeze up)
@kendalgee580810 ай бұрын
Just get it towed. If it's not distilled water , you will get mineral deposits in your engine. Unrelated: If you do a neti pot nasal irrigation with tap water, u may get a brain infection. That is why they use distilled water when doing nasal irrigations.
@RedMango552 жыл бұрын
What happened AFTER a week of driving? New hose needed? I have automotive grade Permatex, good for up to 400 F.
@johnnyweld33282 жыл бұрын
@@RedMango55 sorry for the harsh reply, I was very frustrated with trolls last night. I know a few things about chemicals. My father was national leading salesman for loctite Corp while I was growing up. I developed this product to allow people to fix something very fast. In a lot of cases it is permanent. In a lot of cases it is not. To permanently fix I would cover with Johnny weld to seal immediately and then go over it with permatex. Now you can drive while the permatex dries. Works well to hold items while epoxy cures as well. If you would like ill send you a free bottle. Have a good day bud
@RedMango552 жыл бұрын
@@johnnyweld3328 All good bud. Sometimes we need to step back from online arguments with trolls, they enjoy that kind of game. Your video was informative and useful. There are ingenious ways to fix things and I get inspired. Cheers.
@johnmoore2562 жыл бұрын
I bought a similar product a few years ago and all it turned out to be was super glue and baking soda. So try cheap super glue and a sprinkle of baking soda, it dry very fast and is very strong.
@agungwayne30902 жыл бұрын
LOL, it’ll broke in seconds.
@joshuakent39722 жыл бұрын
Baking soda will work better FYI. The bond is much stronger.
@marklefave33732 жыл бұрын
Where can I buy some
@davidpierce73182 жыл бұрын
I’ve just done mine with a bicycle inner tube repair kit so far so good I’ll look in morning should be ok till I can get new hose
@davidpierce73182 жыл бұрын
Didn’t work
@robertcircleone2 жыл бұрын
My first thought about the white powder is that it is glass powder or glass flour.
@frogsinthepot2 жыл бұрын
Ok, so I glued it to my hand...now what do I do?
@saltpepper18943 жыл бұрын
silicone tape...for perm fix
@highvoltagefeathers3 жыл бұрын
Spoiler: Johnny Weld is baking soda
@johnnyweld66223 жыл бұрын
spoiler: Johnny weld is not baking soda, the chemistry is completely different in how it cures the CA. it does not weaken the CA thru a chemical reaction, it strengthens the CA physically similar to putting fiberglass in resin. Johnny weld also pours freely and doesn't clump up. Have a great day highvoltagefeathers.
@aniketrastogi88683 жыл бұрын
Happened with my car once when the coolant return pipe cracked. I was hundreds of miles away from the nearest authorised service center and was also not in my hometown. Was staying in a hotel. I bought a small pack of epoxy putty and applied a thin layer on the crack - left my vehicle parked in the parking lot overnight to allow it to dry and solidify and then drove back home the next day without any issues of coolant leakage. I got the hose replaced after a year. The epoxy putty held on real strong. Just sharing with in case anyone face such a situation.
@lazycarper79252 жыл бұрын
fuk i hope this is true ive got an old car i cant get a spare hose for
@aniketrastogi88682 жыл бұрын
@@lazycarper7925 there are a number hose repair kits available. You'll be able to find few over the internet as well. But yeah it really depends on the nature of damage and if the hose can be easily patched, you'll be in luck and will hit the road soon.
@deadstreet16752 жыл бұрын
Iv just had a garage try and charge me 800 to replace the hose. I think I will try this first..
@RedMango552 жыл бұрын
@@deadstreet1675 I am thinking Permatex will work. It is an RTV sealant for temp extremes. Need to try on a small leak I have where hose clamps into radiator.
@realworldcodingapplications2 жыл бұрын
you only replaced after a year?? wow that's some quality fix
@TheRogueRockhound3 жыл бұрын
fail
@zaino6603 жыл бұрын
Per how long?
@QOSQualityofSpeed3 жыл бұрын
Thanks a lot for this. It was really good advice I appreciate it
@YouTubeSupportTeams3 жыл бұрын
this guy likes to give himself problems.
@timgreen24263 жыл бұрын
Just use a piece of spare hose & a ton of hose clamps to patch it temporary
@rgh6223 жыл бұрын
Yeah, cause everyone has a spare hose and a ton of hose clamps in an emergency...... Maroon...
@misssummersalt2 жыл бұрын
@@rgh622 I think you meant moron... *ahem*
@rgh6222 жыл бұрын
@@misssummersaltno, I meant maroon.... kzread.info/dash/bejne/kYKNqNNwiq3NZMY.html
@kendalgee580810 ай бұрын
lmfao. it's moron, not maroon.@@rgh622
@GeorgeOtieno8 ай бұрын
@@rgh622 😄😄
@rebeldevil12474 жыл бұрын
i want to know how you bond a piece of glass on top of another piece of glass with no mess and that also looks 100% clear !!!!
@johnnyweld33284 жыл бұрын
Clear silicone and wait about an hour
@apexjoe47694 жыл бұрын
Dude,isn't that glue flammable?Won't the heat buildup from the coolant cause a fire? Man, I wouldn't risk driving the car unless to get me home so I can change the hose.
@johnnyweld33284 жыл бұрын
A coolant hose only gets up to around 200 degrees igloo is only flammable when it is in its liquid state not curedand yes it is a temporary fix to get you to the auto place to get a new hose in no way shape or form is this a permanent fix Thanks for looking average Joe
@cooltu20004 жыл бұрын
I used jb weld
@DougHinVA4 жыл бұрын
a 'solid week of driving' ?? get a replacement hose and install it ot risk ruining a car engine.
@tye5953 жыл бұрын
champ this is a solution when you aren't able to get a replacement hose ..... and his fix lasted a week giving the viewer a good idea how long it will last so you can get a new hose..
@cc_isgreat6714 жыл бұрын
Does it dry clear?
@LilPaulfrmClaraSt4 жыл бұрын
Will it work for a power steering rubber hose ?
@johnnyweld33284 жыл бұрын
Yes it will. Sand or clean the area as much as possible. Don't forget to use multiple layers 4-5 at least.
@zaino6603 жыл бұрын
No
@Hanmablood2 жыл бұрын
Don Nato, .. Yes
@Hanmablood2 жыл бұрын
@@zaino660 yes
@batboy0208764 жыл бұрын
I would still rapid that's stupid to leave it like that that will break
@marilynduenas18764 жыл бұрын
Video has no sound
@samuelneil26914 жыл бұрын
Will this work on trans cooler lines?
@johnnyweld33284 жыл бұрын
Yes, clean all grease and oil from the line and apply 4 to 5 thin layers.
@LilPaulfrmClaraSt4 жыл бұрын
What about a power steering rubber hose ?
@mets23q4 жыл бұрын
Will this work on a fuel hose for a lawnmower?
@milesralls79724 жыл бұрын
Honesty duct tape will work for that
@ashokkumarhamal75505 жыл бұрын
After heat no working this idea
@HernanToroA5 жыл бұрын
Johnny Weld? You mean Baking Soda?
@BrettB2463 жыл бұрын
my thought exactly. I've used SG and BS for a long time now and love the results. Saw this and made me laugh how somebody is trying to sell it as something else. They probably added something else to the baking soda so they can say it's not "baking soda" and claim it's their "proprietary blend". Yeah, 99% baking soda and 1% or less of something else
@johnnyweld33282 жыл бұрын
@@BrettB246 HAHA The ingredients in Johnny Weld are of no physical nature related to baking soda. 100% No baking soda. The Johnny Weld chemistry does not chemically alter/weaken a CA product like baking soda does. Thus resulting in at least 2x stronger bonds.
@gavnonadoroge30925 жыл бұрын
this might hold for couple of days, not more, because of high heat and pressure
@johnnyweld33284 жыл бұрын
Any average super glue will hold a higher heat than a vehicle runs at. Also works well on compressed air hoses and fittings. I've actually fixed leaks on pressure washers that run over 2000psi. On a rubber radiator hose the hose will fail after about 500 miles because the rubber separates without internal fiberglass reinforcement in the affected area. Will get you to a shop and beyond. Thanks for looking
@tonny.salgado.70245 жыл бұрын
were can i purchase? ty
@johnnyweld33283 жыл бұрын
Amazon. Or give me your location and I'll send you the closest distributor. Sorry for not responding for so long
@guesswhomartin92495 жыл бұрын
First, I wanna say, thank you for your video. You did give me an idea. But 2nd, how reliable is this repair you just did ? If I use my car for work making deliveries, and I'm on the road all day, is this patch reliable ? I question that. I cannot take that chance. My income depends on my reliable transportation.
@johnnyweld33285 жыл бұрын
Thank you for your interest. This repair because of the water is good for about a week. Applications without water are generally permanent
@apetcharlie5 жыл бұрын
diy myself. this actually works
@guesswhomartin92494 жыл бұрын
@@apetcharlie .... I'm sure the idea works. But as I stated before, it might temporarily. But I personally wouldn't depend on it long term. I would use the idea just till I get to the auto store and buy a new hose and replace the hose myself, or have a professional mechanic fix it correctly. Thank you again for your input.
@caltari5 жыл бұрын
Will this work with Gel Glue? Thanks in advance.
@johnnyweld33284 жыл бұрын
Yes but cure will be about 5 minutes before completely solid
Пікірлер
Ok, yea, i tried this once with Elmer's glue, and well, i didn't work after the 3rd day, but amazingly enough, it was holding while i was doing 90mph in the corners, Then failure in the last mile, 😭
Better is liquid rubber its flexibile and it will not crack like glue
Just curious, what brand? Thanks
@@sammyhooligan803 I had Bison liquid rubber, but any like that will fix
@@LuXoR1590 gotcha. Yea, right now I'm trying to fix a leak either on a smaller overflow hose? From the top of a Ford explorer '05 radiator or a small fracture on that hose mount hook up. If it's that hose, after I remove it and look for deterioration/ breaks in that rubber hose then, that would be simple to replace, but if it's on that plastic outlet area then i might try either JB weld or something similar for hard plastic construction of radiator. I noticed about 20 ounces low in overflow tank by airbox side, and a small flow of coolant fluid draining from the small hose hookup/ outlet. Maybe I can figure it out, 👍
Super glue and baking soda. Works every time
Can it withstand high pressure?
tried a similar product on a pin hole on a tractor radiator hose does not work the emergency tape gave a much better result had a dew drop leak re wrapped the hose yet to see if the timy dew drop is gone however still have a new hose to fit
pipes like that ususally break when they're really really old and the gazilliont hot/cold cycle takes it toll and perishes the material. a hole will from from the inside, and if you repair that hole, another will appear from elsewhere. the walls of that host are uniformally compromised, do yourself a favour and replace it with a brand new part.
How about melting a tie wrap with a soldering iron over the hose's cut itself? Sounds pretty straightforward to me, since it will literally become part of the hose construction itself...
It will be hot when it breaks
I need to do this rite now...
How much it and dose it comes in a kit wit the white powder or jus the glue??
And then I took the petrol out and drove for 3.14 miles on air for the baby Jesus
What glue/sealant would you recommend for putting together silicone and a metal pip coming off it?
You can also use Baking soda so harden the super glue. Iv never used Jonny weld though so it could be better.
Price
$13-15 depending on where its purchased. Mikeshobby.com has it available online, there's a problem with Amazon that were still trying to figure out
Price
Crazy question could you use gorilla glue
It does make gorilla glue dry about 2x as fast as normal and makes it harder. But your still looking at hours for it to cure
hey, does this works with the radiator coolant reservoir?
Whenever I got a coolant hose leak I find that the simplest cheapest and easiest way to permanently fix it without having to spend sometimes even a $100 for new hose assemblies, is instead a 5 dollar fix: welcome to a simple hose coupling. It costs about 5 bucks and comes with two clamps and u can get one for about any size. What I do is simply cut the hose in half with a razor where the leak is, insert the coupling between the cut, clamp em back up and there ya have it , good as new, no tape, no worrying about it coming off because this is exactly the method the factory uses at the end of the hose, you're just doing it in middle. Good luck! Was surprised not to see anyone on KZread mention this 🤔 Ps: if ur stuck on the side of the road the easiest way to get back home would be taping up the leak with whatever tape u can get ur hands on (many rounds, use the whole roll if yall have to!) and if u have no tape just wrap a towel or cloth as tight as u can and then just loosen the coolant cap enough for some air to get out so u release the pressure on that tape or cloth. Then fill up reservoir with water if u have no coolant. (Make sure u don't leave that water in during the winter as it'll freeze up)
Just get it towed. If it's not distilled water , you will get mineral deposits in your engine. Unrelated: If you do a neti pot nasal irrigation with tap water, u may get a brain infection. That is why they use distilled water when doing nasal irrigations.
What happened AFTER a week of driving? New hose needed? I have automotive grade Permatex, good for up to 400 F.
@@RedMango55 sorry for the harsh reply, I was very frustrated with trolls last night. I know a few things about chemicals. My father was national leading salesman for loctite Corp while I was growing up. I developed this product to allow people to fix something very fast. In a lot of cases it is permanent. In a lot of cases it is not. To permanently fix I would cover with Johnny weld to seal immediately and then go over it with permatex. Now you can drive while the permatex dries. Works well to hold items while epoxy cures as well. If you would like ill send you a free bottle. Have a good day bud
@@johnnyweld3328 All good bud. Sometimes we need to step back from online arguments with trolls, they enjoy that kind of game. Your video was informative and useful. There are ingenious ways to fix things and I get inspired. Cheers.
I bought a similar product a few years ago and all it turned out to be was super glue and baking soda. So try cheap super glue and a sprinkle of baking soda, it dry very fast and is very strong.
LOL, it’ll broke in seconds.
Baking soda will work better FYI. The bond is much stronger.
Where can I buy some
I’ve just done mine with a bicycle inner tube repair kit so far so good I’ll look in morning should be ok till I can get new hose
Didn’t work
My first thought about the white powder is that it is glass powder or glass flour.
Ok, so I glued it to my hand...now what do I do?
silicone tape...for perm fix
Spoiler: Johnny Weld is baking soda
spoiler: Johnny weld is not baking soda, the chemistry is completely different in how it cures the CA. it does not weaken the CA thru a chemical reaction, it strengthens the CA physically similar to putting fiberglass in resin. Johnny weld also pours freely and doesn't clump up. Have a great day highvoltagefeathers.
Happened with my car once when the coolant return pipe cracked. I was hundreds of miles away from the nearest authorised service center and was also not in my hometown. Was staying in a hotel. I bought a small pack of epoxy putty and applied a thin layer on the crack - left my vehicle parked in the parking lot overnight to allow it to dry and solidify and then drove back home the next day without any issues of coolant leakage. I got the hose replaced after a year. The epoxy putty held on real strong. Just sharing with in case anyone face such a situation.
fuk i hope this is true ive got an old car i cant get a spare hose for
@@lazycarper7925 there are a number hose repair kits available. You'll be able to find few over the internet as well. But yeah it really depends on the nature of damage and if the hose can be easily patched, you'll be in luck and will hit the road soon.
Iv just had a garage try and charge me 800 to replace the hose. I think I will try this first..
@@deadstreet1675 I am thinking Permatex will work. It is an RTV sealant for temp extremes. Need to try on a small leak I have where hose clamps into radiator.
you only replaced after a year?? wow that's some quality fix
fail
Per how long?
Thanks a lot for this. It was really good advice I appreciate it
this guy likes to give himself problems.
Just use a piece of spare hose & a ton of hose clamps to patch it temporary
Yeah, cause everyone has a spare hose and a ton of hose clamps in an emergency...... Maroon...
@@rgh622 I think you meant moron... *ahem*
@@misssummersaltno, I meant maroon.... kzread.info/dash/bejne/kYKNqNNwiq3NZMY.html
lmfao. it's moron, not maroon.@@rgh622
@@rgh622 😄😄
i want to know how you bond a piece of glass on top of another piece of glass with no mess and that also looks 100% clear !!!!
Clear silicone and wait about an hour
Dude,isn't that glue flammable?Won't the heat buildup from the coolant cause a fire? Man, I wouldn't risk driving the car unless to get me home so I can change the hose.
A coolant hose only gets up to around 200 degrees igloo is only flammable when it is in its liquid state not curedand yes it is a temporary fix to get you to the auto place to get a new hose in no way shape or form is this a permanent fix Thanks for looking average Joe
I used jb weld
a 'solid week of driving' ?? get a replacement hose and install it ot risk ruining a car engine.
champ this is a solution when you aren't able to get a replacement hose ..... and his fix lasted a week giving the viewer a good idea how long it will last so you can get a new hose..
Does it dry clear?
Will it work for a power steering rubber hose ?
Yes it will. Sand or clean the area as much as possible. Don't forget to use multiple layers 4-5 at least.
No
Don Nato, .. Yes
@@zaino660 yes
I would still rapid that's stupid to leave it like that that will break
Video has no sound
Will this work on trans cooler lines?
Yes, clean all grease and oil from the line and apply 4 to 5 thin layers.
What about a power steering rubber hose ?
Will this work on a fuel hose for a lawnmower?
Honesty duct tape will work for that
After heat no working this idea
Johnny Weld? You mean Baking Soda?
my thought exactly. I've used SG and BS for a long time now and love the results. Saw this and made me laugh how somebody is trying to sell it as something else. They probably added something else to the baking soda so they can say it's not "baking soda" and claim it's their "proprietary blend". Yeah, 99% baking soda and 1% or less of something else
@@BrettB246 HAHA The ingredients in Johnny Weld are of no physical nature related to baking soda. 100% No baking soda. The Johnny Weld chemistry does not chemically alter/weaken a CA product like baking soda does. Thus resulting in at least 2x stronger bonds.
this might hold for couple of days, not more, because of high heat and pressure
Any average super glue will hold a higher heat than a vehicle runs at. Also works well on compressed air hoses and fittings. I've actually fixed leaks on pressure washers that run over 2000psi. On a rubber radiator hose the hose will fail after about 500 miles because the rubber separates without internal fiberglass reinforcement in the affected area. Will get you to a shop and beyond. Thanks for looking
were can i purchase? ty
Amazon. Or give me your location and I'll send you the closest distributor. Sorry for not responding for so long
First, I wanna say, thank you for your video. You did give me an idea. But 2nd, how reliable is this repair you just did ? If I use my car for work making deliveries, and I'm on the road all day, is this patch reliable ? I question that. I cannot take that chance. My income depends on my reliable transportation.
Thank you for your interest. This repair because of the water is good for about a week. Applications without water are generally permanent
diy myself. this actually works
@@apetcharlie .... I'm sure the idea works. But as I stated before, it might temporarily. But I personally wouldn't depend on it long term. I would use the idea just till I get to the auto store and buy a new hose and replace the hose myself, or have a professional mechanic fix it correctly. Thank you again for your input.
Will this work with Gel Glue? Thanks in advance.
Yes but cure will be about 5 minutes before completely solid