My channel has a range of videos from outdoor activities such as SxS/UTV videos & RV/Camping videos, how to videos, DYI videos and product review videos.
Are you saying the S pin and the A pin will have constant 12v. I'm seeing vids where they are hooking up the trickle charger to the A pin. Are they both good?
@grollins34818 күн бұрын
There may be some towing vehicles where the wiring to the 7-pin connector is different. This setup is what I've typically seen. When using this specific Hopkin's plug with a 7 pin to 6 pin cable coming from a 2018 Ford E450, only the S pin should have a constant 12v. The A pin should only get power when the E450 is put into Reverse. You could hook up a 7-pin to six pin connector cable to your towing vehicle and use a multimeter to verify which pin coming from the towing vehicle is always powered and which pin only gets power when the towing vehicle is put into reverse.
@luisorozco703022 күн бұрын
Thanks!!!!
@toddmcminn4722Ай бұрын
Like them just don't like how wires run through the drain plugs..
@grollins3481Ай бұрын
I was a little concerned about that as well, but the rubber on the plugs is so thick that once you run the wires through it basically completely seals around the wires.
@hardya8809Ай бұрын
Looking good! More gas next time 😂
@rodneywilliams3175Ай бұрын
I appreciate the info you've given! Do you still like your ActionTracs? Any cons worth mentioning? Would you buy them again?
@grollins3481Ай бұрын
I really like them, they've worked great since day one. The only con that I have noticed is the constant low power draw from the battery. The manufacturer recommends driving your vehicle at least once a week to ensure the battery stays charged. My jeep is not a daily driver and I may go 2 or 3 weeks without driving it. So I just pull the fuse if I know the jeep is going to be sitting for a while. It's an easy solution for me and if yours is a daily driver then it shouldn't be an issue.
@CHARLIEFOXTROT-qe7mz2 ай бұрын
Ugly lights
@JBK6474 ай бұрын
No link to the lights- ?
@roncerenzia41166 ай бұрын
Have u had any big issues as I am considering this exact unit and hear that right now the new RVs are built very bad along with many issues with slide?
@grollins34816 ай бұрын
This has been a great motorhome for us. We have had only 1 real issue and that's the TV Channel reception. The dealership seems unable to figure out the problem and fix it. I think I have a bad coax cable and just haven't taken the time to troubleshoot it and try to fix it myself. I just connect my iPhone to the TV using an HDMI adapter and stream Netflix and so on. So I guess that's not really a problem. It also tows my Jeep with no problem. We have been very satisfied with it.
@vank7541Ай бұрын
I know this is a late answer because I just came across this video. I like to see how other people use their 30z. We bought a 2023 30 z in February 2023 we had a shade that was broken and they fixed it right away. Later our dinette started pulling away from the wall and our repair person just changed out the middle strip for a heavier one the longer screws. Our Onan generator had the fuel pump go out and luckily we had an Onan repair facility close by. Recently we had a plumbing leak outside underneath the bathroom sink area. Jayco has paid for everything. Minor issues. I hope this helps if you haven't if you haven't bought this specific unit yet.
@simsbertclercent97618 ай бұрын
Remember you can buy it for the driver or passenger side. So just buy for the driver side if you don't want to block your power outlet
@georges45629 ай бұрын
Very nice unit. We have a 2023 30Z and love it so far 👍 Respectfully the 30Z is 32 1/2 feet long bumper to bumper. I will be following your 30 Z adventures 👍👍
@MotoFam_Vlogs9 ай бұрын
How is it opening the door with the knee pad right there? Does it get in the way?
@grollins34819 ай бұрын
Yes, it does get in the way a bit, but it’s not bad. I overlook that issue in favor of the comfort the knee pad provides. You can also choose to use the bags without the knee pad.
@MotoFam_Vlogs9 ай бұрын
@@grollins3481 those knee pads are a must lol. I’ll deal with it as well. Just wondering thank you very much
@okie__moto747411 ай бұрын
Is there a pigtail for the left and right tail lights or does the one you wired on the right the only one needed for the brake lights and turn signals?
@grollins348111 ай бұрын
Only one pigtail is needed. You do need to buy the pigtail separately though.
@michaelvargas166311 ай бұрын
Where did you get the locking device
@grollins348111 ай бұрын
It comes with the case. The same keys you use to unlock the lid is also used for the locking device.
@sthdz2932 Жыл бұрын
Great video
@kevinaj2 Жыл бұрын
What if you have a different backing that won’t let you install, unless I take the bed lin r out that came with the truck, I’m looking for a bed liner to replace the one that I’m taking about installing in the truck, is the an undercover that will fit my truck if I did this???? Please help
@grollins3481 Жыл бұрын
I’m sorry, but I’m not affiliated with the company that makes the case. I’m just an average Joe who figured I would provide a video of how I installed the case on my 2020 GMC. Sorry that I couldn’t be more help.
@kevinaj2 Жыл бұрын
@@grollins3481 thank you very much, do you know how I can get in touch with someone from the company to ask this question, and you have a bless day
@johnenelsonjr Жыл бұрын
Perfect vid. Thanks.
@kensmith8886 Жыл бұрын
The reason the plug is on the back of the storage pocket is because the factory OEM Ford brake controller plugs in this location.
@patrickmulligan3101 Жыл бұрын
I don’t like how it swings closed when you don’t hold it
@grollins3481 Жыл бұрын
Hmm...I don't think I have noticed that. I'll have to check it out.
@teejay622 Жыл бұрын
If I had to guess, I'd say that the plug was located there because that cubby hole above the radio is probably where the factory trailer brake controller would be located if the truck was so equipped. Again, I'm just guessing.
@lindsaycampbell1276 Жыл бұрын
Will you be doing some for a ssangyong musso
@runifuceeme4062 жыл бұрын
LOOKS COOL, BUT WHAT'S THE POINT OF LOCKING IT IF THE SELF TAPS CAN BE LOOSENED OFF THE HINGES AND TAKEN AWAY?.. THAT THING IS AS IMPENETRABLE AS A JUICE BOX.. TOOLS GUARANTEED STOLEN!
@brodybewley58092 жыл бұрын
We’re they flexible right at first or did they slowly break into being flexible
@grollins34812 жыл бұрын
They were flexible from the beginning. So far I'm impressed with them.
@KevinH8792 жыл бұрын
Great video thanka
@rogerlarson80402 жыл бұрын
I spoke with Jayco direct today. They told me the 2022 wiring in the E450 hasn’t changed for the brake wiring. They said the connector is under the dash just like this video shows. I have a class c. 29mvp.
@gregb92642 жыл бұрын
Good job not painting the holes you drilled on a brand new truck Thiss will cause rust and you’re showing people how to install this who will also not paint the holes
@gregb92642 жыл бұрын
@@grollins3481 you soak the screw in paint after painting the hole Or you use silicone around the screw threads so there’s atleast some protection I’m not saying I expect there to be a big pocket of rust you can knock out I’m just saying it’s gonna rust eventually whether it’s noticeable or not Bare metal is bare metal and there’s moisture in the air that will get to it unless you live in Arizona or some extreme example like that
@gregb92642 жыл бұрын
@@grollins3481 and actually now that I think about it Are you sure you don’t have the carbon fiber bed? I know some 2020 GMC models have carbon fiber beds
@fukyu37392 жыл бұрын
It's a GM product, the bedside will rust in 6 years anyway.
@gregb92642 жыл бұрын
@@fukyu3739 oh look a Scotty Kilmer fan
@gregb92642 жыл бұрын
@@fukyu3739 I have a deep scratch in my left side door that can’t be buffed out hasn’t even surface rusted after 8 years I also have a dent from a kid throwing a rock I. The air and taking the paint completely up on my hood to the primer again no rust You’re just another one of those annoying GM haters that have never owned a GM in their life I take it and listen to Scotty
@pewpew10422 жыл бұрын
This was very helpful! I had several questions and you covered them all. Thanks!
@joebailey30072 жыл бұрын
i have a 2020 e-450 with a four winds box i guess the wiring will be the same ?
@grollins34812 жыл бұрын
I think it’s the same. You can always call Camping World’s service department and they will be able to confirm
@chikalirc2 жыл бұрын
Great Video and nice clean install! How big are the Whips? 3 or 4 Ft?
@grollins34812 жыл бұрын
They are the 3 foot
@chikalirc2 жыл бұрын
@@grollins3481 Do you have a link for that pig tail?
@drmarkintexas-4002 жыл бұрын
🏆🏆🏆👍🇺🇲🙏 SUBSCRIBED Thank you for sharing
@davejames95582 жыл бұрын
Great video. I have read that the Swingcase is not compatible with the GM Multipro tailgate, but your truck appears to have one. Can you confirm that?
@grollins34812 жыл бұрын
Thanks, yes I have the Multipro. Tailgate and it works just fine
@adrielitodad.214 Жыл бұрын
Is this the SC104P ?
@AdamsFire115206 ай бұрын
It doesn't work with the multipro on the driver's side cuz there is a handle to help assist with walking up and into the bed.
@jasonfranks26893 жыл бұрын
Blocks the tie downs too
@hdjoe223 жыл бұрын
Seems like it would make a lot of noise, rattling around as you drive…
@grollins34813 жыл бұрын
I’ve not noticed any rattling while driving and I spend a lot of time with the windows down.
@Robnap88 Жыл бұрын
YES! This is whats holding me from hitting the purchase button. It looks and sounds like a rattler. But? Its easy enough to put some self stick weather stripping in spots where there rubbing / rattling and easy enough to coat the box interior with cloth or something to stop any rattling inside the box.
@DrunknOdin3 ай бұрын
I had them in my ram 1500 and they were great. Perfect for tools you need to have on the road but keeps them out of the way til you need them. The case is easy to remove incase you need the space but they are pretty much out of the way.
@hardya88093 жыл бұрын
Good times
@hardya88093 жыл бұрын
Awesome footage. Keep it up
@mrpush25323 жыл бұрын
Can you still get 4' stock in the bed between the boxes?
@mikedean58763 жыл бұрын
I couldn't find the follow up video you said you were going to do. How do you like them? Self tapping screws a issue?
@grollins34813 жыл бұрын
I’ll do a follow up video soon. I wanted to make sure I had enough time with it to give a fair review. COVID limited the amount time I spent using the truck. No issues with the self tapping screws…still as tight as day one and there doesn’t appear to be any corrosion.
@Todd-tz9qq Жыл бұрын
@@grollins3481I can’t find your follow up review. Have you made one? Thanks for posting this video.
@albertodominguez10273 жыл бұрын
What's the model of the box u used? I have sc100p and seem it's won't fit
@steveb76742 жыл бұрын
105p for passenger and 105d for driver 2020 and 2021 gm"s
@24califrank3 жыл бұрын
Hmmmm im gonna pass on this product... I rather just buy the storage box that goes under the back seat
@olivares326883 жыл бұрын
Will this fit on a silveardo 2021 2500hd
@devinmccutcheon9799 Жыл бұрын
I just installed one of these on my 2021 silverado 2500. I got it used off of a Toyota tundra. I just used some heavy duty zip ties and zip tied it to the tie downs and then put the front 2 screws on the bracket. Mine actually sits in closer to the bed wall doing this.
@ClassicRyder13 жыл бұрын
Thanks for doing this video. Been looking at these cases the last few days and wasn't sure how the would fit with the light and outlet. Video was very helpful in making a decision
@ikg20042 жыл бұрын
Yea, it's a negative for me. I use the light and outlet more than the cases.
@miguelpacheco41832 жыл бұрын
@@ikg2004 they have a drivers side version on Amazon for the same price
@TwoEggsOverEasy Жыл бұрын
@@miguelpacheco4183 and you found the drivers side to more efficient. Like you’re not bothered by the fact you can’t easily access the three cargo tie downs? I’m on the fence with this product but definitely leaning towards driver side to not impede the electrical outlet. (New sierra)
@miguelpacheco4183 Жыл бұрын
@@TwoEggsOverEasy not much as I don’t use them to much
@Robnap88 Жыл бұрын
No doubt! The video showed me about the light and outlet I didnt consider. So now I will go inspect my 2022 Colorado and see which side makes more sense. You can buy a unit for either side of the side of the vehicle as others have mentioned.
@SultanofSpey3 жыл бұрын
If anybody wants 2 of these for a 2007-2014 Nissan Frontier. Let me know. [email protected]
@SultanofSpey3 жыл бұрын
I have 2 of these in my current Nissan rig but they hug the truck bed wall and rest directly over the fender wells. I'm very disappointed because I really wanted them in my new Sierra but way too much wasted space. Those boxes don't come close the bed wall, they block the outlet and the LED bed lighting I just paid $1,250 to have included. So pissed. I'm going to have to find something else.
@grollins34813 жыл бұрын
Yeah, but it’s simple to remove if you need better access to the electrical outlet. And it swings out as well.
@SultanofSpey Жыл бұрын
@@grollins3481 Agreed, but it just looks sloppy stticking. I'm pissed because I really like them but I just can't get past how they block the lights and stick out way too far.
@trail_shark60783 жыл бұрын
Cool
@trail_shark60783 жыл бұрын
Tight trails for the X3
@thomasrainbow3 жыл бұрын
Thanks! I have a 2019 GMC Canyon with a Snugtop.. I was considering the Decked drawer system which is super cool but with my new shell I wanted to conserve as much space as possible for camping especially with the short bed. Might have to get these. Cheers!
@gibber19443 жыл бұрын
Any reason why you wouldn't install on the other side so you don't cover the outlet?
@gibber19443 жыл бұрын
I think I can answer my own question after test driving this truck, I assume the reason is the case would block the arm that helps you climb into the box.
@kidluk3 жыл бұрын
Gibber for me personally that arm would come off as soon as I brought the truck home
@sbirdranch3 жыл бұрын
Because it would cover the trailer plug.
@fukyu37392 жыл бұрын
@@sbirdranch The trailer plug is on that side where he installed it. The question was why did he choose to cover it up instead of using a driver side box.
@jarotex2 жыл бұрын
@@fukyu3739 theres an extending grab handle there
@ralphss4344 жыл бұрын
What's to keep someone from stealing the box and your belongings LOL
@grollins34814 жыл бұрын
You can lock it with a padlock.
@andrewsvasquez64583 жыл бұрын
I didnt see a place you can install a padlock
@lewisteixeira10123 жыл бұрын
You can lock it so no one can open it or lift it off.
@grollins34813 жыл бұрын
@@andrewsvasquez6458 Padlock probably isn't the right terminology to use. The box comes with a lock assembly that you can install. I show it near the end of the video.
@squallywally3 жыл бұрын
What keeps them from undoing 4 self tapping bolts and then walking off.?
@77brasileiro4 жыл бұрын
Thanks buddy ! Beats losing real estate in the back of the truck with an enormous case but still have a lockable storage in the back
@howardmiller42414 жыл бұрын
I was thinking of disconnecting mine on my 2019 commander , what r the benefits of disconnecting the sway bar? I know the cons r u will have more body roll but I don’t fly around much I like to crawl around in the woods.
@supporterofsanity4 жыл бұрын
How much does this protrude into the center bed space? Can I still stack sheets of plywood into the bed?
Пікірлер
Are you saying the S pin and the A pin will have constant 12v. I'm seeing vids where they are hooking up the trickle charger to the A pin. Are they both good?
There may be some towing vehicles where the wiring to the 7-pin connector is different. This setup is what I've typically seen. When using this specific Hopkin's plug with a 7 pin to 6 pin cable coming from a 2018 Ford E450, only the S pin should have a constant 12v. The A pin should only get power when the E450 is put into Reverse. You could hook up a 7-pin to six pin connector cable to your towing vehicle and use a multimeter to verify which pin coming from the towing vehicle is always powered and which pin only gets power when the towing vehicle is put into reverse.
Thanks!!!!
Like them just don't like how wires run through the drain plugs..
I was a little concerned about that as well, but the rubber on the plugs is so thick that once you run the wires through it basically completely seals around the wires.
Looking good! More gas next time 😂
I appreciate the info you've given! Do you still like your ActionTracs? Any cons worth mentioning? Would you buy them again?
I really like them, they've worked great since day one. The only con that I have noticed is the constant low power draw from the battery. The manufacturer recommends driving your vehicle at least once a week to ensure the battery stays charged. My jeep is not a daily driver and I may go 2 or 3 weeks without driving it. So I just pull the fuse if I know the jeep is going to be sitting for a while. It's an easy solution for me and if yours is a daily driver then it shouldn't be an issue.
Ugly lights
No link to the lights- ?
Have u had any big issues as I am considering this exact unit and hear that right now the new RVs are built very bad along with many issues with slide?
This has been a great motorhome for us. We have had only 1 real issue and that's the TV Channel reception. The dealership seems unable to figure out the problem and fix it. I think I have a bad coax cable and just haven't taken the time to troubleshoot it and try to fix it myself. I just connect my iPhone to the TV using an HDMI adapter and stream Netflix and so on. So I guess that's not really a problem. It also tows my Jeep with no problem. We have been very satisfied with it.
I know this is a late answer because I just came across this video. I like to see how other people use their 30z. We bought a 2023 30 z in February 2023 we had a shade that was broken and they fixed it right away. Later our dinette started pulling away from the wall and our repair person just changed out the middle strip for a heavier one the longer screws. Our Onan generator had the fuel pump go out and luckily we had an Onan repair facility close by. Recently we had a plumbing leak outside underneath the bathroom sink area. Jayco has paid for everything. Minor issues. I hope this helps if you haven't if you haven't bought this specific unit yet.
Remember you can buy it for the driver or passenger side. So just buy for the driver side if you don't want to block your power outlet
Very nice unit. We have a 2023 30Z and love it so far 👍 Respectfully the 30Z is 32 1/2 feet long bumper to bumper. I will be following your 30 Z adventures 👍👍
How is it opening the door with the knee pad right there? Does it get in the way?
Yes, it does get in the way a bit, but it’s not bad. I overlook that issue in favor of the comfort the knee pad provides. You can also choose to use the bags without the knee pad.
@@grollins3481 those knee pads are a must lol. I’ll deal with it as well. Just wondering thank you very much
Is there a pigtail for the left and right tail lights or does the one you wired on the right the only one needed for the brake lights and turn signals?
Only one pigtail is needed. You do need to buy the pigtail separately though.
Where did you get the locking device
It comes with the case. The same keys you use to unlock the lid is also used for the locking device.
Great video
What if you have a different backing that won’t let you install, unless I take the bed lin r out that came with the truck, I’m looking for a bed liner to replace the one that I’m taking about installing in the truck, is the an undercover that will fit my truck if I did this???? Please help
I’m sorry, but I’m not affiliated with the company that makes the case. I’m just an average Joe who figured I would provide a video of how I installed the case on my 2020 GMC. Sorry that I couldn’t be more help.
@@grollins3481 thank you very much, do you know how I can get in touch with someone from the company to ask this question, and you have a bless day
Perfect vid. Thanks.
The reason the plug is on the back of the storage pocket is because the factory OEM Ford brake controller plugs in this location.
I don’t like how it swings closed when you don’t hold it
Hmm...I don't think I have noticed that. I'll have to check it out.
If I had to guess, I'd say that the plug was located there because that cubby hole above the radio is probably where the factory trailer brake controller would be located if the truck was so equipped. Again, I'm just guessing.
Will you be doing some for a ssangyong musso
LOOKS COOL, BUT WHAT'S THE POINT OF LOCKING IT IF THE SELF TAPS CAN BE LOOSENED OFF THE HINGES AND TAKEN AWAY?.. THAT THING IS AS IMPENETRABLE AS A JUICE BOX.. TOOLS GUARANTEED STOLEN!
We’re they flexible right at first or did they slowly break into being flexible
They were flexible from the beginning. So far I'm impressed with them.
Great video thanka
I spoke with Jayco direct today. They told me the 2022 wiring in the E450 hasn’t changed for the brake wiring. They said the connector is under the dash just like this video shows. I have a class c. 29mvp.
Good job not painting the holes you drilled on a brand new truck Thiss will cause rust and you’re showing people how to install this who will also not paint the holes
@@grollins3481 you soak the screw in paint after painting the hole Or you use silicone around the screw threads so there’s atleast some protection I’m not saying I expect there to be a big pocket of rust you can knock out I’m just saying it’s gonna rust eventually whether it’s noticeable or not Bare metal is bare metal and there’s moisture in the air that will get to it unless you live in Arizona or some extreme example like that
@@grollins3481 and actually now that I think about it Are you sure you don’t have the carbon fiber bed? I know some 2020 GMC models have carbon fiber beds
It's a GM product, the bedside will rust in 6 years anyway.
@@fukyu3739 oh look a Scotty Kilmer fan
@@fukyu3739 I have a deep scratch in my left side door that can’t be buffed out hasn’t even surface rusted after 8 years I also have a dent from a kid throwing a rock I. The air and taking the paint completely up on my hood to the primer again no rust You’re just another one of those annoying GM haters that have never owned a GM in their life I take it and listen to Scotty
This was very helpful! I had several questions and you covered them all. Thanks!
i have a 2020 e-450 with a four winds box i guess the wiring will be the same ?
I think it’s the same. You can always call Camping World’s service department and they will be able to confirm
Great Video and nice clean install! How big are the Whips? 3 or 4 Ft?
They are the 3 foot
@@grollins3481 Do you have a link for that pig tail?
🏆🏆🏆👍🇺🇲🙏 SUBSCRIBED Thank you for sharing
Great video. I have read that the Swingcase is not compatible with the GM Multipro tailgate, but your truck appears to have one. Can you confirm that?
Thanks, yes I have the Multipro. Tailgate and it works just fine
Is this the SC104P ?
It doesn't work with the multipro on the driver's side cuz there is a handle to help assist with walking up and into the bed.
Blocks the tie downs too
Seems like it would make a lot of noise, rattling around as you drive…
I’ve not noticed any rattling while driving and I spend a lot of time with the windows down.
YES! This is whats holding me from hitting the purchase button. It looks and sounds like a rattler. But? Its easy enough to put some self stick weather stripping in spots where there rubbing / rattling and easy enough to coat the box interior with cloth or something to stop any rattling inside the box.
I had them in my ram 1500 and they were great. Perfect for tools you need to have on the road but keeps them out of the way til you need them. The case is easy to remove incase you need the space but they are pretty much out of the way.
Good times
Awesome footage. Keep it up
Can you still get 4' stock in the bed between the boxes?
I couldn't find the follow up video you said you were going to do. How do you like them? Self tapping screws a issue?
I’ll do a follow up video soon. I wanted to make sure I had enough time with it to give a fair review. COVID limited the amount time I spent using the truck. No issues with the self tapping screws…still as tight as day one and there doesn’t appear to be any corrosion.
@@grollins3481I can’t find your follow up review. Have you made one? Thanks for posting this video.
What's the model of the box u used? I have sc100p and seem it's won't fit
105p for passenger and 105d for driver 2020 and 2021 gm"s
Hmmmm im gonna pass on this product... I rather just buy the storage box that goes under the back seat
Will this fit on a silveardo 2021 2500hd
I just installed one of these on my 2021 silverado 2500. I got it used off of a Toyota tundra. I just used some heavy duty zip ties and zip tied it to the tie downs and then put the front 2 screws on the bracket. Mine actually sits in closer to the bed wall doing this.
Thanks for doing this video. Been looking at these cases the last few days and wasn't sure how the would fit with the light and outlet. Video was very helpful in making a decision
Yea, it's a negative for me. I use the light and outlet more than the cases.
@@ikg2004 they have a drivers side version on Amazon for the same price
@@miguelpacheco4183 and you found the drivers side to more efficient. Like you’re not bothered by the fact you can’t easily access the three cargo tie downs? I’m on the fence with this product but definitely leaning towards driver side to not impede the electrical outlet. (New sierra)
@@TwoEggsOverEasy not much as I don’t use them to much
No doubt! The video showed me about the light and outlet I didnt consider. So now I will go inspect my 2022 Colorado and see which side makes more sense. You can buy a unit for either side of the side of the vehicle as others have mentioned.
If anybody wants 2 of these for a 2007-2014 Nissan Frontier. Let me know. [email protected]
I have 2 of these in my current Nissan rig but they hug the truck bed wall and rest directly over the fender wells. I'm very disappointed because I really wanted them in my new Sierra but way too much wasted space. Those boxes don't come close the bed wall, they block the outlet and the LED bed lighting I just paid $1,250 to have included. So pissed. I'm going to have to find something else.
Yeah, but it’s simple to remove if you need better access to the electrical outlet. And it swings out as well.
@@grollins3481 Agreed, but it just looks sloppy stticking. I'm pissed because I really like them but I just can't get past how they block the lights and stick out way too far.
Cool
Tight trails for the X3
Thanks! I have a 2019 GMC Canyon with a Snugtop.. I was considering the Decked drawer system which is super cool but with my new shell I wanted to conserve as much space as possible for camping especially with the short bed. Might have to get these. Cheers!
Any reason why you wouldn't install on the other side so you don't cover the outlet?
I think I can answer my own question after test driving this truck, I assume the reason is the case would block the arm that helps you climb into the box.
Gibber for me personally that arm would come off as soon as I brought the truck home
Because it would cover the trailer plug.
@@sbirdranch The trailer plug is on that side where he installed it. The question was why did he choose to cover it up instead of using a driver side box.
@@fukyu3739 theres an extending grab handle there
What's to keep someone from stealing the box and your belongings LOL
You can lock it with a padlock.
I didnt see a place you can install a padlock
You can lock it so no one can open it or lift it off.
@@andrewsvasquez6458 Padlock probably isn't the right terminology to use. The box comes with a lock assembly that you can install. I show it near the end of the video.
What keeps them from undoing 4 self tapping bolts and then walking off.?
Thanks buddy ! Beats losing real estate in the back of the truck with an enormous case but still have a lockable storage in the back
I was thinking of disconnecting mine on my 2019 commander , what r the benefits of disconnecting the sway bar? I know the cons r u will have more body roll but I don’t fly around much I like to crawl around in the woods.
How much does this protrude into the center bed space? Can I still stack sheets of plywood into the bed?