Sir I have dis model Problem cod erro6 what problem dis
@optimascale6851Ай бұрын
Typically try to calibrate like in the video. If that doesn't help maybe problem with main PCB. You might need to check the wiring. Here is another video on the channel about this. kzread.info/dash/bejne/poqWtpeAprCvXdI.htmlsi=m8ziorYWR2xXBqfO Thanks, Anthony
@jonvogel7644Ай бұрын
I spent 2 hours trying to figure it out on my own with the manual and in less than 2 minutes of video... I've finally got it working! Thank you!
@optimascale6851Ай бұрын
Glad it helped! -Anthony
@muhammadrozan18023 ай бұрын
Thank you for the tutorial
@myaqoob68423 ай бұрын
Nice 👍
@falalumahmood4 ай бұрын
Please can u install floor scale without junction box
@optimascale68513 ай бұрын
No since there is 4 load cells. The indicators only have room for 1 connection. You can connect one load cells directly to indicator but that is all. Other option would be to buy OP903 which has 4 5 pin connectors and attach a 5 pin connector to each load cell and connect that to each port of 903. Thanks, Anthony
@lolofranco59754 ай бұрын
Hola estimado amigo,podrías indicarme las configuraciones para poder calibrar un indicador de peso para ganado op-900 ?
@optimascale68514 ай бұрын
C01-2 C02-0 C03-1 C04-5000 C05-1 C06-1 Tengo un manual en español en nuestro sitio web aquí. www.optimascale.com/manuals Thanks, Anthony
@lolofranco59754 ай бұрын
@@optimascale6851 hermano,con mucha sinceridad agradezco el tiempo que te has tomado para contestarme.Te comento rápido,que yo calibré esa báscula la cual se usa para pesar ganado y el punto está que una vez calibrada cuando se realiza prueba de peso con una res el peso se mantiene oscilante,no estable.podría ser falta de configuración en la sensibilidad?
@ejray2k5 ай бұрын
This was very helpful. Thanks!
@Bartes_terazi_sistemleri5 ай бұрын
Hello, where can you buy the white color printer and program?
@optimascale68514 ай бұрын
Sorry for taking long time to respond. Email [email protected] to place your order. Anthony
@krizianannferranco30226 ай бұрын
Hm
@thabisovuyohlalukana50377 ай бұрын
I've tried this but it just doesn't work for me. It connects but doesn't give me any data.
@jerven11283 ай бұрын
have you checked your port?
@morkovija8 ай бұрын
thank you for detailed explanation. Surprisingly there arent that many videos on the subject
@hotjulysun9 ай бұрын
Ours won’t zero out.
@optimascale68519 ай бұрын
If your readout is older than 2-3 years old there might be a problem with the readout. You might need to replace. We discontinued the OP902 and replaced with OP909JR. Ask for the 4 to 5 pin adapter. email: [email protected] to place order. Otherwise it could be damaged cable someone is sales can help you with that. Anthony
@TheIntertainers10 ай бұрын
What position should the lever on the handle be when you install it?
@optimascale685110 ай бұрын
About 45 degrees
@TheIntertainers10 ай бұрын
@@optimascale6851 I'm sorry, I meant the three-position operational handle lever
Now they are good values so load cells are good How we knew if they are bad if ot comes morr resistamce??? 😊
@optimascale685111 ай бұрын
Only way to check is add voltage over red and black and measure output resistance as weight is being added.
@jyvben152011 ай бұрын
for windows, the program used was Putty, this also works on linux, where the port(s) are /dev/tty.... e.g. ttyACM0, ttyUSB0 the linux user (not root) might need to be part of the dialout group, do the following in a terminal (need sudo rights) sudo adduser $USER dialout (where $USER points to the current logged in active user, or replace it with your logon name )
@GrandMughal-369.11 ай бұрын
Kindly make single ponit loadcell making compelete process vidio.
@i_like_lasers Жыл бұрын
amazing. big thanks
@bluebox9971 Жыл бұрын
question, there is a wireless version of this, what is the name of the board used for making it wireless?
@optimascale685111 ай бұрын
You can use what you want. We have used the digi xbee in the past.
@optimascale685111 ай бұрын
Anthony
@user-hq8rl2rw9u Жыл бұрын
Where can I purchase a replacement battery for my pallet jack, I can't seem to find them anywhere.
@optimascale6851 Жыл бұрын
email [email protected] with which color battery you have we have in stock.
@user-zt4dw4bb6z Жыл бұрын
How can 12 cells be connected together?
@optimascale6851 Жыл бұрын
You can use a 12 port junction box. We only have 10 ports here. Second option is to use to SECTIONAL junction boxes for example 2 8 port junction boxes where 1 goes into into to the input of the other junction box. Diagram would be readout -> junction box 1 (4 load cells) -> junction box 2 (8 load cells).
@rondemus9736 Жыл бұрын
Necesito el esquema de como soldarlo
@optimascale6851 Жыл бұрын
Rojo-TX Verde - RX Negro-tierra
@ethanengle7927 Жыл бұрын
Hey man, great videos. I do have a question about error 3 and 4 for the 900b ex. As well as when a scale head is powered on and just has dashes and won’t let me do anything.
@optimascale6851 Жыл бұрын
error 3 is input signal is negative. This usually happens when the green and white wires are swap and giving a negative signal. You can check the C15 setting to see how it responds to weight. The video on the channel called how to fix a floor scale explains more about this. error 4 happens when weight is unstable. Usually customers put too many decimals that their scale can't handle. Try to use less decimals and try out. If it still happens then probably damaged cable to readout. Check C15 setting as well. I haven't seen the dashes probably overload or short in cable. Try to go into settings and recalibrate. email: [email protected] for any specific questions you have.
@stuartmorales308 Жыл бұрын
How do you turn on the Battery Indicator??
@optimascale6851 Жыл бұрын
It should turn on when pressing the power button up front. Make sure power cables connected. Anthony
@kamalabdalla7326 Жыл бұрын
Nice
@OrVardi-ik9pd Жыл бұрын
is there a way to have this print in Excel
@optimascale6851 Жыл бұрын
You would need some kind of software. Here is a video below on an example software we make. kzread.info/dash/bejne/f56Aj5Vph6nXfbA.html
@SaurabhPatel-qx9sg Жыл бұрын
Thank you for your demo for calibration. It worked for the ULINE floor scale too.
@optimascale6851 Жыл бұрын
Yes, we ship for ULINE as well. Sometimes they rebadge our scales as their own or find another supplier and do the same. All scales work the same so the any videos on this channel will help. Anthony
@timothyabanigbe7913 Жыл бұрын
Thank you
@hoangthe8196 Жыл бұрын
where download Software ?
@optimascale6851 Жыл бұрын
We sell this software. You can email: [email protected] to purchase. Mentions you want to buy data logging software. They can give you a price.
@hoangthe8196 Жыл бұрын
@@optimascale6851 thank you .
@Mkhayra Жыл бұрын
I like
@daleskiballadares8387 Жыл бұрын
Espani
@Ziggs3182 жыл бұрын
Love your videos bro. I work for Data Weighing Systems out in Wood Dale IL and your videos help me a lot. Question, are those batteries rechargeable or will they need to be replaced every year or so?
@optimascale68512 жыл бұрын
These are reachable. Same as a phone they are not meant to be replaced. These batteries should last from 3-5 years depending on how often they are used. Anthony
@MohamedAslanAffan2 жыл бұрын
Very useful 👌.. i want to know what happens when we calibrate a weighing scale.changes occurs in indicator? or in load cell?
@optimascale68512 жыл бұрын
Calibration is stored on the indicator. Load cell is just a sensor. If you take the calibrated indicator and switch load cells to a different load cell of same capacity it will weigh the same.
@annonymousme25282 жыл бұрын
I was wondering if you can help with my scales , my scales were send out and working from who sent them but upon receiving them they didn't work, I pulled them apart to find what looks like a wire soldered in wrong spot could this be why they say unstable
@annonymousme25282 жыл бұрын
I turn on my scale and all is says is "un-st then after a moment fluctuates in weight to 14kg and then goes to o-ld " it doesn't start up normally it just says unst ...
@optimascale68512 жыл бұрын
You can watch my video on how to fix a floor scale for a more detailed answered. kzread.info/dash/bejne/qZeOuaV_YLW0Ybg.html It could be wire in the wrong location, maybe needs to be recalibrated or bad load cell. Only way to tell is making sure all wiring is correct and tight and recalibrate. If there is water in the junction box then that will cause fluctuating weight. You will need to replace that junction box. You can email [email protected] for junction box replacement or if you find a bad load cell. Thanks, Anthony
@larryaltavilla14722 жыл бұрын
WE HAVE STRUGGLED WITH THIS INDICATOR FOR YEARS.
@optimascale68512 жыл бұрын
Yes it is difficult. If you have a problem with one port you can check the F4 raw data for that connector and see what is going on. You can email: [email protected] with your problem for more help.
@fakboii69882 жыл бұрын
Error 4? Plis
@fakboii69882 жыл бұрын
T scale err4
@optimascale68512 жыл бұрын
Happens when weight is not stable. Make sure your test weight isn't moving. If it is not moving then check the wiring in the junction box in the platform. It could be 1 wire loose. Watch my how to fix a floor scale video on more details. Thanks, Anthony
@fakboii69882 жыл бұрын
@@optimascale6851 thank you, for showing me how to overcome it
@linloadcell1582 жыл бұрын
700Ω
@optimascale68512 жыл бұрын
Check the green and white wires and check that ohm reading. Then Green and black should be around the same. Load cells usually don't go bad. Try to rewire and check the C15 setting. Check out how to fix a floor scale video for more details. Thanks, Anthony
@linloadcell1582 жыл бұрын
Load cells
@hamzahfc84902 жыл бұрын
Vc 50 cely err6
@joshuaalibocas60422 жыл бұрын
hi anthony can we get a peak at the relay boards ,great videos by the way
@optimascale68512 жыл бұрын
What is your email. I can send it to you. It is a extra board and connector that is soldered on the board.
@shaikmeharaj50112 жыл бұрын
Sir ur last check the signal combination of .Green+Red one pair, Green+Black its showing 555Ohm what is the valve plz tell me
@optimascale68512 жыл бұрын
Green+Red and Green+Black should be between maybe 5-50 ohms difference depending on the load cell. If you have the spec sheet or model number I can help determine what the ohm value should be.
@cessromer70782 жыл бұрын
For servicing or design customer display using VBA, C#, Visual Basic or python and/or transfer data to display it over a HTML page . Please contact me.
@cessromer70782 жыл бұрын
For servicing or design customer display using VBA, C#, Visual Basic or python and/or transfer data to display it over a HTML page . Please contact me.
@cessromer70782 жыл бұрын
Also it should be check each wiring compare with the metalic case of the load cell to check for ground failure.
@manikde44822 жыл бұрын
In a PCB in market ,in place of connection for load cell where normally Black red green white are printed, but this one printed on as E-,E+,S+,S-,. Which color wire represent these ?
@optimascale68512 жыл бұрын
E+ = Red E- = Black S+ = Green S- = White
@manikde44822 жыл бұрын
@@optimascale6851 thanks.
@javiermarino36622 жыл бұрын
INDICADOR BKCscales calibration please
@optimascale68512 жыл бұрын
This is for calibration. Si busca a alguien que pueda ayudar en español puede llamar al 1.800.360.9619 ext. 2 tenemos gente aquí que puede ayudar.
Пікірлер
Good
Sir I have dis model Problem cod erro6 what problem dis
Typically try to calibrate like in the video. If that doesn't help maybe problem with main PCB. You might need to check the wiring. Here is another video on the channel about this. kzread.info/dash/bejne/poqWtpeAprCvXdI.htmlsi=m8ziorYWR2xXBqfO Thanks, Anthony
I spent 2 hours trying to figure it out on my own with the manual and in less than 2 minutes of video... I've finally got it working! Thank you!
Glad it helped! -Anthony
Thank you for the tutorial
Nice 👍
Please can u install floor scale without junction box
No since there is 4 load cells. The indicators only have room for 1 connection. You can connect one load cells directly to indicator but that is all. Other option would be to buy OP903 which has 4 5 pin connectors and attach a 5 pin connector to each load cell and connect that to each port of 903. Thanks, Anthony
Hola estimado amigo,podrías indicarme las configuraciones para poder calibrar un indicador de peso para ganado op-900 ?
C01-2 C02-0 C03-1 C04-5000 C05-1 C06-1 Tengo un manual en español en nuestro sitio web aquí. www.optimascale.com/manuals Thanks, Anthony
@@optimascale6851 hermano,con mucha sinceridad agradezco el tiempo que te has tomado para contestarme.Te comento rápido,que yo calibré esa báscula la cual se usa para pesar ganado y el punto está que una vez calibrada cuando se realiza prueba de peso con una res el peso se mantiene oscilante,no estable.podría ser falta de configuración en la sensibilidad?
This was very helpful. Thanks!
Hello, where can you buy the white color printer and program?
Sorry for taking long time to respond. Email [email protected] to place your order. Anthony
Hm
I've tried this but it just doesn't work for me. It connects but doesn't give me any data.
have you checked your port?
thank you for detailed explanation. Surprisingly there arent that many videos on the subject
Ours won’t zero out.
If your readout is older than 2-3 years old there might be a problem with the readout. You might need to replace. We discontinued the OP902 and replaced with OP909JR. Ask for the 4 to 5 pin adapter. email: [email protected] to place order. Otherwise it could be damaged cable someone is sales can help you with that. Anthony
What position should the lever on the handle be when you install it?
About 45 degrees
@@optimascale6851 I'm sorry, I meant the three-position operational handle lever
Legend for making this!! Thanks
how can get that indicator...i need 1
Email [email protected] to purchase.
Thank you
Now they are good values so load cells are good How we knew if they are bad if ot comes morr resistamce??? 😊
Only way to check is add voltage over red and black and measure output resistance as weight is being added.
for windows, the program used was Putty, this also works on linux, where the port(s) are /dev/tty.... e.g. ttyACM0, ttyUSB0 the linux user (not root) might need to be part of the dialout group, do the following in a terminal (need sudo rights) sudo adduser $USER dialout (where $USER points to the current logged in active user, or replace it with your logon name )
Kindly make single ponit loadcell making compelete process vidio.
amazing. big thanks
question, there is a wireless version of this, what is the name of the board used for making it wireless?
You can use what you want. We have used the digi xbee in the past.
Anthony
Where can I purchase a replacement battery for my pallet jack, I can't seem to find them anywhere.
email [email protected] with which color battery you have we have in stock.
How can 12 cells be connected together?
You can use a 12 port junction box. We only have 10 ports here. Second option is to use to SECTIONAL junction boxes for example 2 8 port junction boxes where 1 goes into into to the input of the other junction box. Diagram would be readout -> junction box 1 (4 load cells) -> junction box 2 (8 load cells).
Necesito el esquema de como soldarlo
Rojo-TX Verde - RX Negro-tierra
Hey man, great videos. I do have a question about error 3 and 4 for the 900b ex. As well as when a scale head is powered on and just has dashes and won’t let me do anything.
error 3 is input signal is negative. This usually happens when the green and white wires are swap and giving a negative signal. You can check the C15 setting to see how it responds to weight. The video on the channel called how to fix a floor scale explains more about this. error 4 happens when weight is unstable. Usually customers put too many decimals that their scale can't handle. Try to use less decimals and try out. If it still happens then probably damaged cable to readout. Check C15 setting as well. I haven't seen the dashes probably overload or short in cable. Try to go into settings and recalibrate. email: [email protected] for any specific questions you have.
How do you turn on the Battery Indicator??
It should turn on when pressing the power button up front. Make sure power cables connected. Anthony
Nice
is there a way to have this print in Excel
You would need some kind of software. Here is a video below on an example software we make. kzread.info/dash/bejne/f56Aj5Vph6nXfbA.html
Thank you for your demo for calibration. It worked for the ULINE floor scale too.
Yes, we ship for ULINE as well. Sometimes they rebadge our scales as their own or find another supplier and do the same. All scales work the same so the any videos on this channel will help. Anthony
Thank you
where download Software ?
We sell this software. You can email: [email protected] to purchase. Mentions you want to buy data logging software. They can give you a price.
@@optimascale6851 thank you .
I like
Espani
Love your videos bro. I work for Data Weighing Systems out in Wood Dale IL and your videos help me a lot. Question, are those batteries rechargeable or will they need to be replaced every year or so?
These are reachable. Same as a phone they are not meant to be replaced. These batteries should last from 3-5 years depending on how often they are used. Anthony
Very useful 👌.. i want to know what happens when we calibrate a weighing scale.changes occurs in indicator? or in load cell?
Calibration is stored on the indicator. Load cell is just a sensor. If you take the calibrated indicator and switch load cells to a different load cell of same capacity it will weigh the same.
I was wondering if you can help with my scales , my scales were send out and working from who sent them but upon receiving them they didn't work, I pulled them apart to find what looks like a wire soldered in wrong spot could this be why they say unstable
I turn on my scale and all is says is "un-st then after a moment fluctuates in weight to 14kg and then goes to o-ld " it doesn't start up normally it just says unst ...
You can watch my video on how to fix a floor scale for a more detailed answered. kzread.info/dash/bejne/qZeOuaV_YLW0Ybg.html It could be wire in the wrong location, maybe needs to be recalibrated or bad load cell. Only way to tell is making sure all wiring is correct and tight and recalibrate. If there is water in the junction box then that will cause fluctuating weight. You will need to replace that junction box. You can email [email protected] for junction box replacement or if you find a bad load cell. Thanks, Anthony
WE HAVE STRUGGLED WITH THIS INDICATOR FOR YEARS.
Yes it is difficult. If you have a problem with one port you can check the F4 raw data for that connector and see what is going on. You can email: [email protected] with your problem for more help.
Error 4? Plis
T scale err4
Happens when weight is not stable. Make sure your test weight isn't moving. If it is not moving then check the wiring in the junction box in the platform. It could be 1 wire loose. Watch my how to fix a floor scale video on more details. Thanks, Anthony
@@optimascale6851 thank you, for showing me how to overcome it
700Ω
Check the green and white wires and check that ohm reading. Then Green and black should be around the same. Load cells usually don't go bad. Try to rewire and check the C15 setting. Check out how to fix a floor scale video for more details. Thanks, Anthony
Load cells
Vc 50 cely err6
hi anthony can we get a peak at the relay boards ,great videos by the way
What is your email. I can send it to you. It is a extra board and connector that is soldered on the board.
Sir ur last check the signal combination of .Green+Red one pair, Green+Black its showing 555Ohm what is the valve plz tell me
Green+Red and Green+Black should be between maybe 5-50 ohms difference depending on the load cell. If you have the spec sheet or model number I can help determine what the ohm value should be.
For servicing or design customer display using VBA, C#, Visual Basic or python and/or transfer data to display it over a HTML page . Please contact me.
For servicing or design customer display using VBA, C#, Visual Basic or python and/or transfer data to display it over a HTML page . Please contact me.
Also it should be check each wiring compare with the metalic case of the load cell to check for ground failure.
In a PCB in market ,in place of connection for load cell where normally Black red green white are printed, but this one printed on as E-,E+,S+,S-,. Which color wire represent these ?
E+ = Red E- = Black S+ = Green S- = White
@@optimascale6851 thanks.
INDICADOR BKCscales calibration please
This is for calibration. Si busca a alguien que pueda ayudar en español puede llamar al 1.800.360.9619 ext. 2 tenemos gente aquí que puede ayudar.
Hello, how are you my friend, can we talk?