I've done a great deal of equipment repair welding. I have to agree with many of the comments on this repair job especially the prep work (or lack of) and the use of 6013 rods instead of a 7018 type. But, in their defense, we don't know all the details or the demands placed on them, or what they have for equipment or skills. I'm sure they do the best they can with what they have and if we were in their shoes maybe we'd do the same.
@user-iq7to3ms8d17 сағат бұрын
Good work ❤
@johnt72322 күн бұрын
No fitter welders there just a bunch of chancers , then I suppose pay peanuts get monkeys
@horstmuller75123 күн бұрын
Good job! All tolerances are guaranteed less than 5 fingers.
@SkillMasters-vy2lo2 күн бұрын
Thanks
@codymcdaniel50904 күн бұрын
I feel like so much of their issues could be fixed if they just did some damn prep work and not rushed in.
@craneoperator375 күн бұрын
I have a lot of hours in 966D and 966E loaders like this one, used in mine duty. NEVER saw any of the cracks and breaks like on this poor machine. I would like to see the operators in action. Also, the welding rod they are using is a Bridge Supreme J421, which is a 6013 classification. Should be a 80 or 70 low hydrogen rod used on those loader arms.
@vsvnrg32632 күн бұрын
yes, i was wondering what theyve been doing. the machine doesnt look like its got that many hours up on it for the all the cracks all over the boom.
@user-iv2uc8nf8y6 күн бұрын
back street job not inpressed at all
@thomasjones6138 күн бұрын
I worked in a rock quarry for years as a welder repairing the heavy equipment and rock crushers. What these people did here to "repair" this 966 boom is utterly embarrassing!
@swarfs5 күн бұрын
OK Mr big clever big dick. Mr Thomasjones613.. Now enlighten us ordinary normal people what you would do to mend it. Don't just criticise, Mr clever precious.
@marioleon8224Күн бұрын
exactly fella
@TheHomePros62218 күн бұрын
Defiently ain’t no cutting edge engineering 🤮
@ZiaratWali9 күн бұрын
Good work
@ZiaratWali9 күн бұрын
Good work ❤
@attaullahkhan73459 күн бұрын
Wooo amazing 😮😮
@user-wr5jv8nm4d10 күн бұрын
goodjob
@attaullahkhan734510 күн бұрын
Great job 👍
@_Dimitriy_11 күн бұрын
0:50 - 1:10 и снова всё отвалится по тем же местам. Чем тратить деньги и время (что в условиях интенсивной эксплуатации тоже деньги) на бесконечные ремонты, не дешевле было бы купить новый или б/у, но не выработавший свой ресурс узел? Или труд там настолько дёшев, что...
@mechanic_life2711 күн бұрын
Amazing
@SkillMasters-vy2lo10 күн бұрын
Thinks
@banuamekanikal45412 күн бұрын
good wheel loader pin bushing repair, friend 👍👍
@SkillMasters-vy2lo12 күн бұрын
Thanks bro
@richardmiller523813 күн бұрын
👌💯excellent
@SkillMasters-vy2lo13 күн бұрын
Thanks you
@richardmiller523813 күн бұрын
💯👌👌😎
@nicokyriak14 күн бұрын
This Loader Boom has been repaired over and over again in the same place and they keep making the same mistakes.
@SkillMasters-vy2lo13 күн бұрын
Thanks 🙏
@ferdinandocappelletti674014 күн бұрын
Good work, done outside the workshop,my compliments !
@SkillMasters-vy2lo14 күн бұрын
Thinks ❤️
@user-oz8he6dg5l14 күн бұрын
Great work😮wow beatiful
@SkillMasters-vy2lo14 күн бұрын
Thanks
@attaullahkhan734516 күн бұрын
So amazing work I like it ❤
@SkillMasters-vy2lo16 күн бұрын
Thanks 🙏
@user-wr5jv8nm4d15 күн бұрын
ok
@2wwwilly18 күн бұрын
Add a doubler plate as reinforcement..😂😂❤❤
@user-wr5jv8nm4d16 күн бұрын
greatjob
@IbrahimKhan-cs4og18 күн бұрын
Good 👍
@user-wr5jv8nm4d19 күн бұрын
good work
@pauljohnstone472319 күн бұрын
The welds are full of slag and it will break again next week.
@SkillMasters-vy2lo19 күн бұрын
Thanks you 👌
@ichkackmirindiehoish20 күн бұрын
Oh mein Gott 🫣😂😅. Zwei Wochen später, wieder das gleiche machen🤦♂️. Schaut euch lieber CEE an, der hat wenigstens Ahnung und kann richtig reparieren. Das hier ist nur Pfusch
@SkillMasters-vy2lo20 күн бұрын
Thinks
@user-wr5jv8nm4d20 күн бұрын
good video
@user-wr5jv8nm4d20 күн бұрын
great video
@attaullahkhan734521 күн бұрын
Great job 👍
@attaullahkhan734521 күн бұрын
Great work.
@attaullahkhan734521 күн бұрын
Great work.
@user-fz6vs4de9m22 күн бұрын
they always amaze me
@SkillMasters-vy2lo21 күн бұрын
Thinks
@georgemaru465322 күн бұрын
A Patchy Indians..😂
@IdiotDrivers49122 күн бұрын
Such creative videos you’ve on this channel. Just subscribed!
@attaullahkhan734521 күн бұрын
Thanks 👍🙏
@SkillMasters-vy2lo19 күн бұрын
Thinks bro ❤️👌
@user-iq7to3ms8d23 күн бұрын
So good
@SkillMasters-vy2lo23 күн бұрын
Thinks
@user-wr5jv8nm4d20 күн бұрын
great job
@sportsfan20523 күн бұрын
Never seen a loader with so many cracks.
@SkillMasters-vy2lo23 күн бұрын
Thniks
@Sussilando14 күн бұрын
Ich auch nicht und ich habe Jahrelang so ein Lader (Hanomag E 60) gefahren! Aber hier ist falsche Anwendung,Überlasteter Einsatz,einseitige Belastung u Fehlbedienung die Ursache. Es gibt Leute,die bekommen alles kaputt auch ein Panzer!!
@SkillMasters-vy2lo13 күн бұрын
@@Sussilando okay 👌
@Amazingskillmaster23 күн бұрын
Good job
@IdiotDrivers49122 күн бұрын
Hello, my friend!
@tillross407824 күн бұрын
Torc converter bolt failure cracked housing caused fault in bearing witch hurt pump , I'm I close ? Got the same thing on D 5 dozer ,, good job people 👍🙏
@SkillMasters-vy2lo24 күн бұрын
Thinks
@Sussilando16 күн бұрын
und alles im Dreck repariert!1😅 Eine Schraube nichtmehr eingebaut!🤗
@SkillMasters-vy2lo15 күн бұрын
@@Sussilando ❤️❤️
@momalmom229426 күн бұрын
ماشاء الله 👍👍👍👍
@SkillMasters-vy2lo26 күн бұрын
Thenks
@udo547927 күн бұрын
The Paint is the Superstructure on this Loader
@Sussilando14 күн бұрын
🤣
@Tatal.b27 күн бұрын
👍👍👍👍
@user-wr5jv8nm4d29 күн бұрын
amazing work
@vacipkonuk4168Ай бұрын
Ustalar kolay gelsin. Bir civatayı iptal ettiniz, çok güzel ama balans işini nasıl hallettiniz? anlamadım.
Пікірлер
I've done a great deal of equipment repair welding. I have to agree with many of the comments on this repair job especially the prep work (or lack of) and the use of 6013 rods instead of a 7018 type. But, in their defense, we don't know all the details or the demands placed on them, or what they have for equipment or skills. I'm sure they do the best they can with what they have and if we were in their shoes maybe we'd do the same.
Good work ❤
No fitter welders there just a bunch of chancers , then I suppose pay peanuts get monkeys
Good job! All tolerances are guaranteed less than 5 fingers.
Thanks
I feel like so much of their issues could be fixed if they just did some damn prep work and not rushed in.
I have a lot of hours in 966D and 966E loaders like this one, used in mine duty. NEVER saw any of the cracks and breaks like on this poor machine. I would like to see the operators in action. Also, the welding rod they are using is a Bridge Supreme J421, which is a 6013 classification. Should be a 80 or 70 low hydrogen rod used on those loader arms.
yes, i was wondering what theyve been doing. the machine doesnt look like its got that many hours up on it for the all the cracks all over the boom.
back street job not inpressed at all
I worked in a rock quarry for years as a welder repairing the heavy equipment and rock crushers. What these people did here to "repair" this 966 boom is utterly embarrassing!
OK Mr big clever big dick. Mr Thomasjones613.. Now enlighten us ordinary normal people what you would do to mend it. Don't just criticise, Mr clever precious.
exactly fella
Defiently ain’t no cutting edge engineering 🤮
Good work
Good work ❤
Wooo amazing 😮😮
goodjob
Great job 👍
0:50 - 1:10 и снова всё отвалится по тем же местам. Чем тратить деньги и время (что в условиях интенсивной эксплуатации тоже деньги) на бесконечные ремонты, не дешевле было бы купить новый или б/у, но не выработавший свой ресурс узел? Или труд там настолько дёшев, что...
Amazing
Thinks
good wheel loader pin bushing repair, friend 👍👍
Thanks bro
👌💯excellent
Thanks you
💯👌👌😎
This Loader Boom has been repaired over and over again in the same place and they keep making the same mistakes.
Thanks 🙏
Good work, done outside the workshop,my compliments !
Thinks ❤️
Great work😮wow beatiful
Thanks
So amazing work I like it ❤
Thanks 🙏
ok
Add a doubler plate as reinforcement..😂😂❤❤
greatjob
Good 👍
good work
The welds are full of slag and it will break again next week.
Thanks you 👌
Oh mein Gott 🫣😂😅. Zwei Wochen später, wieder das gleiche machen🤦♂️. Schaut euch lieber CEE an, der hat wenigstens Ahnung und kann richtig reparieren. Das hier ist nur Pfusch
Thinks
good video
great video
Great job 👍
Great work.
Great work.
they always amaze me
Thinks
A Patchy Indians..😂
Such creative videos you’ve on this channel. Just subscribed!
Thanks 👍🙏
Thinks bro ❤️👌
So good
Thinks
great job
Never seen a loader with so many cracks.
Thniks
Ich auch nicht und ich habe Jahrelang so ein Lader (Hanomag E 60) gefahren! Aber hier ist falsche Anwendung,Überlasteter Einsatz,einseitige Belastung u Fehlbedienung die Ursache. Es gibt Leute,die bekommen alles kaputt auch ein Panzer!!
@@Sussilando okay 👌
Good job
Hello, my friend!
Torc converter bolt failure cracked housing caused fault in bearing witch hurt pump , I'm I close ? Got the same thing on D 5 dozer ,, good job people 👍🙏
Thinks
und alles im Dreck repariert!1😅 Eine Schraube nichtmehr eingebaut!🤗
@@Sussilando ❤️❤️
ماشاء الله 👍👍👍👍
Thenks
The Paint is the Superstructure on this Loader
🤣
👍👍👍👍
amazing work
Ustalar kolay gelsin. Bir civatayı iptal ettiniz, çok güzel ama balans işini nasıl hallettiniz? anlamadım.
Please cleaning before fitting brother
Okay
G
😮😮
❤❤
❤❤❤❤
Good
Good