What I need for my 8 pistons breaks I have a 2023 challenger rt
@_demon1k_18 күн бұрын
If these calipers have a radial mount and the same parameters from the mount to the center of the caliper, adapter will definitely work for you
@KamGlobaI18 күн бұрын
@@_demon1k_ I’m sorry about that I meant 6 pistons and I have the rotors that goes with them and break line
@_demon1k_18 күн бұрын
@@KamGlobaI If you're talking about the 6 piston hellcat calipers you only need the srt steering knuckles, otherwise you can't install them, there is no adapter for those calipers
@fstattoohornby490325 күн бұрын
Legend has it nanna still has it stuck in 1st gear
@_demon1k_25 күн бұрын
🤣 When you know everything in this world, there's no hurry.
@lonelybikr27 күн бұрын
Love these cars.
@darrellboyer4004Ай бұрын
I'd like to see a part for the rest of the repair
@_demon1k_28 күн бұрын
I have shown the rest of the repair parts in the following videos
@NaleezeАй бұрын
bro how do i get that bracket
@_demon1k_Ай бұрын
I don’t sell ready-made adapters, I can only sell a 3d model for manufacturing in your city
@hemi08911Ай бұрын
Man great video. Do yo sell them Caliper adapters i need a pair asap.
@_demon1k_Ай бұрын
I don’t sell ready-made adapters, I can only sell a 3d model for manufacturing in your city
@345JoАй бұрын
@@_demon1k_how much for the 3d model?
@_demon1k_Ай бұрын
@@345Jo The cost of the model is 50€=55$=75CA$
@brandonsmith58272 ай бұрын
Did you have to remove the steering wheel to swap this out? I'd like to try and leave mine attached if possible.
@_demon1k_2 ай бұрын
You don't need to remove the steering wheel to remove the dash, just push it toward you and down.
@brandonsmith58272 ай бұрын
Thanks! I’m going to be doing this soon. Do you recommend removing all the duct work sections (driver, passenger, and the center section that’s screwed to the dash panel) out all together? Looks like you kept the drivers section in the car when you did yours.
@_demon1k_2 ай бұрын
@@brandonsmith5827 You must remove all sections of the air duct or you will not be able to remove the instrument panel without damaging the windshield heating duct.
@_demon1k_2 ай бұрын
@@brandonsmith5827 To remove the air ducts unscrew the screws at the racks, remove the clip in the center and be sure to remove the screw that is behind the dashboard, this screw is the most difficult to access
@brandonsmith58272 ай бұрын
Is there just one screw back there and is that the one you show in your video?
@Jehuty802 ай бұрын
Copies BMW lights
@_demon1k_2 ай бұрын
No, completely different headlights
@ma932562 ай бұрын
Where did you get the display from?
@_demon1k_2 ай бұрын
I bought it on eBay
@ma932562 ай бұрын
@@_demon1k_ can you please provide the link? Thank you
@_demon1k_2 ай бұрын
@@ma93256 www.ebay.com/itm/324916320246
@ma932562 ай бұрын
@@_demon1k_ thank you! 🙏🏼
@_demon1k_2 ай бұрын
@@ma93256 you are welcome
@lilivideogame4882 ай бұрын
it's not the car the problem but the guy who remove mufflers on it
@_demon1k_2 ай бұрын
Yeah, it's not everyone's favorite, but that's not me, my car has a stock exhaust.
@kinanalhawat67532 ай бұрын
Its actually not that bad I really don't understand why so many people are annoyed just by the car starting and driving away or coming home.
@relguiatmont73362 ай бұрын
Compare it to a Ford, Chevy or anyone's top trim V8 cars.. Its just louder on a cold start.
@_demon1k_2 ай бұрын
I don't get it either.
@_demon1k_2 ай бұрын
@@relguiatmont7336 I agree with you 100%
@Thatrandomwhiteguy2 ай бұрын
Think again my 18s move windows 3 blocks away😂
@_demon1k_2 ай бұрын
Nice joke 🤣
@Thatrandomwhiteguy2 ай бұрын
@@_demon1k_ not a joke.. i see you, have never been in a monster... look up competition car or home stereos.. SPL is everything you're missing.. 150db literally just get you in the club.. & no you dont need to be rich just good with numbers..
@@Thatrandomwhiteguy Would love to watch and listen to your competition car. A stereo system is a whole other topic of conversation
@vincentborges57452 ай бұрын
Why cuz ur black?
@mallorydrolet91852 ай бұрын
Do a burnout next time
@_demon1k_2 ай бұрын
No, no, no, no, I try not to do that😅
@ChryslerLeBaro2 ай бұрын
Keep cranking and the problem will be the battery. How are your plugs? Have to checked them?
@_demon1k_2 ай бұрын
You have to rev the motor for a very long time for the battery problem to show up. No problem with the fuses
@ChryslerLeBaro2 ай бұрын
@@_demon1k_ So you’ve changed the spark plugs?
@_demon1k_2 ай бұрын
@@ChryslerLeBaro No, I haven't, but I still have low mileage so I was surprised to see such a malfunction
@jasonbunch89742 ай бұрын
Out of gas
@_demon1k_2 ай бұрын
No, full tank
@Carsedits292 ай бұрын
Maybe fuel pump
@_demon1k_2 ай бұрын
Yeah, you're right.
@Carsedits292 ай бұрын
Battery
@_demon1k_2 ай бұрын
No
@alandln3 ай бұрын
It look dirty!
@_demon1k_3 ай бұрын
It does, it takes a lot of time and wipes to clean off the glue between the touchscreen and the screen
@sarahbodner21023 ай бұрын
Could have just gone through up top where intake is and reach down. So much easier. Most videos do it this way though.
@_demon1k_3 ай бұрын
I'm not sure it would be easier that way, it would require removing more parts to get to the side markers
@GaryR-lr2qn3 ай бұрын
Outstanding work! I have a 2016 Challenger R/T, RWD with Scat Pack package and 4 piston Brembo brakes and want to upgrade to a 6 piston Brembo kit. Brembo tech support said it will not fit. The brackets in this video would help to install the 6 piston Brembo kit? If, yes, I am interested in the blue prints of the brackets. Thank you for your help.
@_demon1k_3 ай бұрын
If you have 4 piston brembo calipers, you don't need adapters because you have SRT knuckles. Just buy 6-piston calipers and hellcat brake disks.
@christianhardwick653013 күн бұрын
$1340 for rotors.
@_demon1k_13 күн бұрын
@@christianhardwick6530 price depends on the supplier and condition, this price is for new, but you can always buy used in excellent condition for half price or even cheaper. But the point is that the difference in braking is enormous, they are worth their money
@zesusflacko3 ай бұрын
How would you go about straightening an aluminum hood?
@_demon1k_3 ай бұрын
Aluminum is also metal and can be straightened, but only small bends, I was just practicing on this hood, but such damage should not be repaired
@kosharidze4 ай бұрын
@kosharidze4 ай бұрын
Congrats with Sponsorships program
@_demon1k_4 ай бұрын
Thank you so much😍
@geedub3994 ай бұрын
Great vid 👍🏻
@_demon1k_4 ай бұрын
Thanks
@dominikgsell4694 ай бұрын
Do u Sell 2 of These Adapters? I have a 2012er r/t, and want 4-6 piston calipers…. But its impossible to get srt knuckle in Germany … if u Sell These Adapters…. Which calipers i will need? Great work btw!❤
@_demon1k_4 ай бұрын
I can sell you a 3D model of the adapter and you make it in your city on any milling or CNC machine. You will need Brembo GT calipers 6 or 8 piston calipers for 380-410mm/34mm brake disk (for today it is the newest model) or any available in your country Brembo calipers with radial mount for such disk, for example from Audi, Porsche, Mercedes or Bmw.
@dominikgsell4694 ай бұрын
@@_demon1k_ what do you want for this? The idea with Porsche calipers Sounds wonderful, i only have to Look what Modell These calipers use (have no idea of Porsche 😌) are the screw holes of all brembo caliper are the same ?
@_demon1k_4 ай бұрын
@@dominikgsell469 For example, calipers like the ones in the photo forums.quattroworld.com/rs4b7/msgs/98644.phtml It is important that they can be installed on large brake disks, because the disk from the hellcat is 390/34mm. It is important that the mounting holes are 200mm and the distance from the holes to the caliper axle is 55mm I used this caliper, its price in Europe is 450 euros a piece www.brembo.com/en/car/sporting-use/gt-braking-systems
@_demon1k_4 ай бұрын
@@dominikgsell469 For 3D model cost, write me on instagram or better yet email me at [email protected] I will need to understand in what format you will need the model or drawings
@dominikgsell4694 ай бұрын
@@_demon1k_ ok i will thx :-)
@JulioHernandez-zx1sv4 ай бұрын
I have a Dodge Durango 2015 RT 5.7 V8 and I want to installed the brembo caliper with the bracket where I can buy the same you installed in the video. My car is a rear traction . Thank you
@_demon1k_4 ай бұрын
I need to understand what kind of steering knuckle is used on your car, if the same as on a rear wheel drive Challenger or Charger then my adapter will work for you and I can sell you a 3d model or drawings for fabrication. If you are using a different knuckle then you will need to design a different adapter, but I don't have data on the Durango range of knuckles at this time.
@JulioHernandez-zx1sv4 ай бұрын
I have a charger 6 Piston front caliper for my Dodge Durango RT V8 2015 5.7 and my knuckle number is PSA46700. I want to adapt that brembo calipers to my Durango you think that is possible. Thank you for your help.
@_demon1k_4 ай бұрын
@@JulioHernandez-zx1sv There is not much place to mount the hellcat caliper to the steering knuckle via an adapter, as the hellcat caliper is laterally mounted to the steering knuckle . So I used a caliper with a radial mount so that an adapter of sufficient strength could be made. In your case, it would be easiest to mount the caliper without an adapter to the steering knuckle and use a two-piece brake disc like on a Charger or Challenger Hellcat, but fabricate a new center section to fit the required caliper outreach. I think that would be the easiest way to install these calipers.
@pushhrodd014 ай бұрын
My friend I just wanted to say that you’re a genius and a very hard worker. Here in the United States where these cars are common you would make a very good living selling this things on the side. Good job on the work. You did great!!
@_demon1k_4 ай бұрын
Thank you for such an appreciation of my work
@DeepFinger-UA4 ай бұрын
🇺🇦🫶🏻❤️
@5.7_nightbrd4 ай бұрын
yoo sick ass carbon fiber hood and those brembos look beautiful 😮💨
@_demon1k_4 ай бұрын
Thanks
@yungswagg8848Ай бұрын
I’m doing my Charger rt.
@davidlowe37935 ай бұрын
Can we buy these brackets or did you have them made ? And what caliper is that from scat?
@_demon1k_5 ай бұрын
I can sell 3D model or blueprints to make the adapter. The adapter can be made on any CNC or milling machine in your city. I used new generation Brembo GT series calipers with radial mounts. You can buy them from a Brembo dealer: www.brembo.com/en/car/sporting-use/gt-braking-systems
@tworeckless75685 ай бұрын
My 2019 RT Daytona came with them I thought Daytonas came with brembos but I guess not. Dealer add on when it’s a 5.7?
@_demon1k_5 ай бұрын
Yes, on all v8 you can add the performance brake package as an option and then you have brakes like a hellcat
@d7mmi1065 ай бұрын
All versions of monitors can be installed smoothly ? what is the difference
@_demon1k_5 ай бұрын
No, only on car monitors of 2016 year of release from the manufacturer panasonic, before 2016 were put magnetos from the manufacturer Harman and they do not have this problem, there screens are originally from two parts - the screen and touchscreen
@user-rm2cn9mk2l5 ай бұрын
2:55 what is that part called???
@_demon1k_5 ай бұрын
68258750AC
@UtilitieSupply5 ай бұрын
Outstanding work. You should be selling these.
@_demon1k_5 ай бұрын
Thanks
@jeremymcclain8914 ай бұрын
What are they? I have a 2006 dodge magnum srt8 and just got 2016 hellcat 6 piston calipers and 2 piece rotors. Could I use this product? It looks just like yours.
@_demon1k_4 ай бұрын
@@jeremymcclain891 If you have the magnum version of the srt8, you don't need additional adapters, you already have the srt front steering knuckles that the 6 piston calipers from hellcat mount to
@EdgarGarcia-gi4dk5 ай бұрын
Were can i get it?
@_demon1k_5 ай бұрын
I can provide a 3d model or drawings to make the adapter. To buy a model write to me in instagram or email
@alexarambula2806Ай бұрын
@_demon1k_ how do I get them?
@dairiezstownes965911 күн бұрын
Im interested in a set@@_demon1k_
@mclaurinxjuju36476 ай бұрын
so hellcat brakes would fit on my RT with the bracket?
@_demon1k_6 ай бұрын
No, hellcat calipers can be installed on RT only with SRT knuckles, because hellcat calipers are side mount (end mount). The adapter is designed to fit Brembo radial mount calipers without replacing the knuckles on RT, SXT, GT models
@stanleypatterson43756 ай бұрын
That looks fantastic will it work for the Jeeps also?
@_demon1k_6 ай бұрын
Yes, I plan to develop an adapter for jeep but right now I don't have a steering knuckle to scan the dimensions
@jeremymcclain8914 ай бұрын
Let me know if you need parts to scan. I have a 2006 dodge magnum srt8 and would love to use your adapters. We can work something out. I could send you parts to scan. You should come to America, and get out of there til things get better.
@_demon1k_4 ай бұрын
@@jeremymcclain891 Thanks! This adapter is designed for cars that don't have srt steering knuckles so you can install big brakes like on a hellcat. On models that use the srt steering knuckles, the brakes from the Hellcat can be installed without modification.
@wraithmedaberry57956 ай бұрын
V6
@_demon1k_6 ай бұрын
Hemi
@moetaz42986 ай бұрын
hey man, I've been looking for something like this for a long time. Can I please get the bracket file from you? I have a 2015 RT challenger and I am looking to upgrade the front brakes. thanks
@_demon1k_6 ай бұрын
wrote a reply on instagram
@dawidkorzeniowski61007 ай бұрын
hello mate, i will drop u an email soon
@richardmaldonado5747 ай бұрын
Still looks horrible , and the music , goodness
@jeffbendertheenforcer58347 ай бұрын
This is by far the best easiest way to fix your UConnect ! Thanks for sharing video !!
@LordLoMR28 ай бұрын
So much work, better off buying a new one. 😂
@_demon1k_8 ай бұрын
This was to gain experience working with aluminum. Later I did as you say)
@raenzoperformance96008 ай бұрын
Fair play guys you done a great job well done alot of work gone in
@_demon1k_8 ай бұрын
Thanks
@lar_chosl36478 ай бұрын
Свист вражеских ракет😡😡 Это ужас! Сумасшедшая опасность же!
@skybudd8 ай бұрын
How much would you charge me to draw a plate?
@_demon1k_8 ай бұрын
write me a message on Instagram (instagram.com/_demon1k_/) or email ([email protected])
@ItsMLorenzo8 ай бұрын
@@_demon1k_did you make a new ig account?
@markparadis51678 ай бұрын
Do you the OEM part numbers for the air dam and front fascia?
@_demon1k_8 ай бұрын
front fascia - 68258730AB air dam - 68258745AB
@charleshamm11999 ай бұрын
What tool did you use to take out that ribbon on the back?
@_demon1k_9 ай бұрын
To separate the touchscreen from the screen, I used a string to separate the screens.
Пікірлер
Мужик похоже и сам не рад, что это затеял
😁
What I need for my 8 pistons breaks I have a 2023 challenger rt
If these calipers have a radial mount and the same parameters from the mount to the center of the caliper, adapter will definitely work for you
@@_demon1k_ I’m sorry about that I meant 6 pistons and I have the rotors that goes with them and break line
@@KamGlobaI If you're talking about the 6 piston hellcat calipers you only need the srt steering knuckles, otherwise you can't install them, there is no adapter for those calipers
Legend has it nanna still has it stuck in 1st gear
🤣 When you know everything in this world, there's no hurry.
Love these cars.
I'd like to see a part for the rest of the repair
I have shown the rest of the repair parts in the following videos
bro how do i get that bracket
I don’t sell ready-made adapters, I can only sell a 3d model for manufacturing in your city
Man great video. Do yo sell them Caliper adapters i need a pair asap.
I don’t sell ready-made adapters, I can only sell a 3d model for manufacturing in your city
@@_demon1k_how much for the 3d model?
@@345Jo The cost of the model is 50€=55$=75CA$
Did you have to remove the steering wheel to swap this out? I'd like to try and leave mine attached if possible.
You don't need to remove the steering wheel to remove the dash, just push it toward you and down.
Thanks! I’m going to be doing this soon. Do you recommend removing all the duct work sections (driver, passenger, and the center section that’s screwed to the dash panel) out all together? Looks like you kept the drivers section in the car when you did yours.
@@brandonsmith5827 You must remove all sections of the air duct or you will not be able to remove the instrument panel without damaging the windshield heating duct.
@@brandonsmith5827 To remove the air ducts unscrew the screws at the racks, remove the clip in the center and be sure to remove the screw that is behind the dashboard, this screw is the most difficult to access
Is there just one screw back there and is that the one you show in your video?
Copies BMW lights
No, completely different headlights
Where did you get the display from?
I bought it on eBay
@@_demon1k_ can you please provide the link? Thank you
@@ma93256 www.ebay.com/itm/324916320246
@@_demon1k_ thank you! 🙏🏼
@@ma93256 you are welcome
it's not the car the problem but the guy who remove mufflers on it
Yeah, it's not everyone's favorite, but that's not me, my car has a stock exhaust.
Its actually not that bad I really don't understand why so many people are annoyed just by the car starting and driving away or coming home.
Compare it to a Ford, Chevy or anyone's top trim V8 cars.. Its just louder on a cold start.
I don't get it either.
@@relguiatmont7336 I agree with you 100%
Think again my 18s move windows 3 blocks away😂
Nice joke 🤣
@@_demon1k_ not a joke.. i see you, have never been in a monster... look up competition car or home stereos.. SPL is everything you're missing.. 150db literally just get you in the club.. & no you dont need to be rich just good with numbers..
kzread.info/dash/bejne/nGxpl5eFgJDVkbQ.htmlsi=3X6iqsNhOnkPrX1V
kzread.info/dash/bejne/nGxpl5eFgJDVkbQ.htmlsi=3X6iqsNhOnkPrX1V
@@Thatrandomwhiteguy Would love to watch and listen to your competition car. A stereo system is a whole other topic of conversation
Why cuz ur black?
Do a burnout next time
No, no, no, no, I try not to do that😅
Keep cranking and the problem will be the battery. How are your plugs? Have to checked them?
You have to rev the motor for a very long time for the battery problem to show up. No problem with the fuses
@@_demon1k_ So you’ve changed the spark plugs?
@@ChryslerLeBaro No, I haven't, but I still have low mileage so I was surprised to see such a malfunction
Out of gas
No, full tank
Maybe fuel pump
Yeah, you're right.
Battery
No
It look dirty!
It does, it takes a lot of time and wipes to clean off the glue between the touchscreen and the screen
Could have just gone through up top where intake is and reach down. So much easier. Most videos do it this way though.
I'm not sure it would be easier that way, it would require removing more parts to get to the side markers
Outstanding work! I have a 2016 Challenger R/T, RWD with Scat Pack package and 4 piston Brembo brakes and want to upgrade to a 6 piston Brembo kit. Brembo tech support said it will not fit. The brackets in this video would help to install the 6 piston Brembo kit? If, yes, I am interested in the blue prints of the brackets. Thank you for your help.
If you have 4 piston brembo calipers, you don't need adapters because you have SRT knuckles. Just buy 6-piston calipers and hellcat brake disks.
$1340 for rotors.
@@christianhardwick6530 price depends on the supplier and condition, this price is for new, but you can always buy used in excellent condition for half price or even cheaper. But the point is that the difference in braking is enormous, they are worth their money
How would you go about straightening an aluminum hood?
Aluminum is also metal and can be straightened, but only small bends, I was just practicing on this hood, but such damage should not be repaired
Congrats with Sponsorships program
Thank you so much😍
Great vid 👍🏻
Thanks
Do u Sell 2 of These Adapters? I have a 2012er r/t, and want 4-6 piston calipers…. But its impossible to get srt knuckle in Germany … if u Sell These Adapters…. Which calipers i will need? Great work btw!❤
I can sell you a 3D model of the adapter and you make it in your city on any milling or CNC machine. You will need Brembo GT calipers 6 or 8 piston calipers for 380-410mm/34mm brake disk (for today it is the newest model) or any available in your country Brembo calipers with radial mount for such disk, for example from Audi, Porsche, Mercedes or Bmw.
@@_demon1k_ what do you want for this? The idea with Porsche calipers Sounds wonderful, i only have to Look what Modell These calipers use (have no idea of Porsche 😌) are the screw holes of all brembo caliper are the same ?
@@dominikgsell469 For example, calipers like the ones in the photo forums.quattroworld.com/rs4b7/msgs/98644.phtml It is important that they can be installed on large brake disks, because the disk from the hellcat is 390/34mm. It is important that the mounting holes are 200mm and the distance from the holes to the caliper axle is 55mm I used this caliper, its price in Europe is 450 euros a piece www.brembo.com/en/car/sporting-use/gt-braking-systems
@@dominikgsell469 For 3D model cost, write me on instagram or better yet email me at [email protected] I will need to understand in what format you will need the model or drawings
@@_demon1k_ ok i will thx :-)
I have a Dodge Durango 2015 RT 5.7 V8 and I want to installed the brembo caliper with the bracket where I can buy the same you installed in the video. My car is a rear traction . Thank you
I need to understand what kind of steering knuckle is used on your car, if the same as on a rear wheel drive Challenger or Charger then my adapter will work for you and I can sell you a 3d model or drawings for fabrication. If you are using a different knuckle then you will need to design a different adapter, but I don't have data on the Durango range of knuckles at this time.
I have a charger 6 Piston front caliper for my Dodge Durango RT V8 2015 5.7 and my knuckle number is PSA46700. I want to adapt that brembo calipers to my Durango you think that is possible. Thank you for your help.
@@JulioHernandez-zx1sv There is not much place to mount the hellcat caliper to the steering knuckle via an adapter, as the hellcat caliper is laterally mounted to the steering knuckle . So I used a caliper with a radial mount so that an adapter of sufficient strength could be made. In your case, it would be easiest to mount the caliper without an adapter to the steering knuckle and use a two-piece brake disc like on a Charger or Challenger Hellcat, but fabricate a new center section to fit the required caliper outreach. I think that would be the easiest way to install these calipers.
My friend I just wanted to say that you’re a genius and a very hard worker. Here in the United States where these cars are common you would make a very good living selling this things on the side. Good job on the work. You did great!!
Thank you for such an appreciation of my work
🇺🇦🫶🏻❤️
yoo sick ass carbon fiber hood and those brembos look beautiful 😮💨
Thanks
I’m doing my Charger rt.
Can we buy these brackets or did you have them made ? And what caliper is that from scat?
I can sell 3D model or blueprints to make the adapter. The adapter can be made on any CNC or milling machine in your city. I used new generation Brembo GT series calipers with radial mounts. You can buy them from a Brembo dealer: www.brembo.com/en/car/sporting-use/gt-braking-systems
My 2019 RT Daytona came with them I thought Daytonas came with brembos but I guess not. Dealer add on when it’s a 5.7?
Yes, on all v8 you can add the performance brake package as an option and then you have brakes like a hellcat
All versions of monitors can be installed smoothly ? what is the difference
No, only on car monitors of 2016 year of release from the manufacturer panasonic, before 2016 were put magnetos from the manufacturer Harman and they do not have this problem, there screens are originally from two parts - the screen and touchscreen
2:55 what is that part called???
68258750AC
Outstanding work. You should be selling these.
Thanks
What are they? I have a 2006 dodge magnum srt8 and just got 2016 hellcat 6 piston calipers and 2 piece rotors. Could I use this product? It looks just like yours.
@@jeremymcclain891 If you have the magnum version of the srt8, you don't need additional adapters, you already have the srt front steering knuckles that the 6 piston calipers from hellcat mount to
Were can i get it?
I can provide a 3d model or drawings to make the adapter. To buy a model write to me in instagram or email
@_demon1k_ how do I get them?
Im interested in a set@@_demon1k_
so hellcat brakes would fit on my RT with the bracket?
No, hellcat calipers can be installed on RT only with SRT knuckles, because hellcat calipers are side mount (end mount). The adapter is designed to fit Brembo radial mount calipers without replacing the knuckles on RT, SXT, GT models
That looks fantastic will it work for the Jeeps also?
Yes, I plan to develop an adapter for jeep but right now I don't have a steering knuckle to scan the dimensions
Let me know if you need parts to scan. I have a 2006 dodge magnum srt8 and would love to use your adapters. We can work something out. I could send you parts to scan. You should come to America, and get out of there til things get better.
@@jeremymcclain891 Thanks! This adapter is designed for cars that don't have srt steering knuckles so you can install big brakes like on a hellcat. On models that use the srt steering knuckles, the brakes from the Hellcat can be installed without modification.
V6
Hemi
hey man, I've been looking for something like this for a long time. Can I please get the bracket file from you? I have a 2015 RT challenger and I am looking to upgrade the front brakes. thanks
wrote a reply on instagram
hello mate, i will drop u an email soon
Still looks horrible , and the music , goodness
This is by far the best easiest way to fix your UConnect ! Thanks for sharing video !!
So much work, better off buying a new one. 😂
This was to gain experience working with aluminum. Later I did as you say)
Fair play guys you done a great job well done alot of work gone in
Thanks
Свист вражеских ракет😡😡 Это ужас! Сумасшедшая опасность же!
How much would you charge me to draw a plate?
write me a message on Instagram (instagram.com/_demon1k_/) or email ([email protected])
@@_demon1k_did you make a new ig account?
Do you the OEM part numbers for the air dam and front fascia?
front fascia - 68258730AB air dam - 68258745AB
What tool did you use to take out that ribbon on the back?
To separate the touchscreen from the screen, I used a string to separate the screens.