Пікірлер

• 
  @MiguelMarquez-i1o2 күн бұрын

  Nice one!! your car looks very cool by the way 👌🏼👏🏼

• 
  @micron32682 күн бұрын

  Thank you, much appreciated!👍

• 
  @BriansRCStuff5 күн бұрын

  All good with you?

• 
  @micron32682 күн бұрын

  Yeah, Thanks for asking!👊 I was out of town for a bit and just haven't been able to get out and make runs the last three weeks! 😞 Now I'm able and ready too but its rain for the next three days!😭 lol

• 
  @BriansRCStuff2 күн бұрын

  @@micron3268 that sucks, but I’m glad all is good!

• 
  @skyhawk217 күн бұрын

  How far did you put droop screws in and how did you measure when lowering it? Also did you use stock radio and gyro in receiver for speed runs at all? Would a hobbywing wp 120a 4s non sensor esc work ok for 4s on stock 3650 motor? Did you move shock positions at all or adjust?

• 
  @Nino-hd3sp8 күн бұрын

  Voila une belle video en 4s

• 
  @93jdmmike13 күн бұрын

  Nice work and really nice chassis buddy keep pushing

• 
  @micron326812 күн бұрын

  Thanks man, much appreciated! 👍

• 
  @93jdmmike13 күн бұрын

  Nice work

• 
  @micron326813 күн бұрын

  Thanks for taking a look, appreciate it!

• 
  @JesseBlum16 күн бұрын

  Hey bud! So I have a tire issue. I bought a 4s certified racing tire but even at 60 percent it spins to fact and the tire gets to thin, but I been using a 6s now at 50percent on the dial and anything over 45mph the wheels turn into paper lol.

• 
  @micron326815 күн бұрын

  If you're using it for speed runs try foams, but for bashing I really don't know what to tell you man!

• 
  @JesseBlum15 күн бұрын

  @micron3268 ya just for speed runs. Bc in quite sure w The way I have it set up right now it goes somewhere between 70-90mph for sure

• 
  @jasonjohnson608525 күн бұрын

  Amazing pass and so close to the curb but you drove that sucker. Nice

• 
  @micron326825 күн бұрын

  Thanks bud, I was lucky that day! lol👍

• 
  @cesleywright848725 күн бұрын

  Where did you get the carbon front splitter

• 
  @micron326825 күн бұрын

  I made everything myself bud!👍

• 
  @BriansRCStuff29 күн бұрын

  Wow, that is moving!!!

• 
  @micron326829 күн бұрын

  Moving toward the curb!🤣 Thanks Brian!👍

• 
  @BriansRCStuff29 күн бұрын

  @@micron3268 I am pretty sure they make their own gravity.

• 
  @micron326829 күн бұрын

  @@BriansRCStuff RCs and curbs, It's like a golf ball and water!🧲 😂

• 
  @djtazzmtl29 күн бұрын

  I have 4100KV Hobby Wing with the Max 10 80A. With 3S 11.4 HV LiPo. With Belted Badlands Mx28. I'm hitting about 75Km/h I think it's nuts lol.

• 
  @BriansRCStuffАй бұрын

  Outstanding speed there! You are killing it!

• 
  @micron3268Ай бұрын

  Thanks a lot, I appreciate that!👊👍

• 
  @RcprescriptionАй бұрын

  Awesome pass brother! 2s is crazy!🤜🤛

• 
  @micron3268Ай бұрын

  Thanks, much appreciated!👍

• 
  @RlaarloАй бұрын

  Wow, what an incredible video! A lot of people don’t know how to properly upgrade their RC cars, so your tutorial on the dual motor Rlaarlo AK-917 is absolutely invaluable. That crazy 6s pass was mind-blowing!

• 
  @micron3268Ай бұрын

  Thank you for the support! Love your RCs!👍

• 
  @scottbronson9738Ай бұрын

  I love this car!🏁🏁🏁

• 
  @micron3268Ай бұрын

  Thanks!

• 
  @scottbronson9738Ай бұрын

  Most awesome!🏁🏁🏁

• 
  @micron3268Ай бұрын

  Thanks, much appreciated!👍

• 
  @mitchellminer4596Ай бұрын

  Nice save buddy. Always a plus when there is no carnage ! 👊👍👍 congrats on the pb for the car!

• 
  @micron3268Ай бұрын

  Man I definitely got lucky on that one!😅 Thanks taking a look!!👍👍

• 
  @MarkusKern-dp3jvАй бұрын

  💪💪💪💪

• 
  @JesseBlumАй бұрын

  I blew my stock tires yesterday on my 4s whoops. How are these? Do you have alink

• 
  @RCSpeedster100Ай бұрын

  Awesome job 👏

• 
  @micron3268Ай бұрын

  Thanks, I appreciate that!👍

• 
  @RcghostnrkАй бұрын

  Nice hit micron keep it up

• 
  @micron3268Ай бұрын

  Thanks Ghost, very much appreciated!👊👍

• 
  @mitchellminer4596Ай бұрын

  Great pass buddy! Congrats 👊👍👍

• 
  @micron3268Ай бұрын

  Thank you, much appreciated!👍

• 
  @skyhawk21Ай бұрын

  What wheels are those and does Amazon got them?

• 
  @micron3268Ай бұрын

  They are JACO Foams Part# JAC2050LP, and I'm not sure about Amazon? I purchased them at Nankin Hobby, my local hobby shop! 👍

• 
  @JesseBlumАй бұрын

  Are those the foam tires.

• 
  @micron3268Ай бұрын

  They are JACO Foams Part# JAC2050LP! 👍

• 
  @JesseBlumАй бұрын

  Yes 4s on these only way to go!! I upgraded to a 6500kv motor with a 20t pinion and Jesus christ haha

• 
  @micron3268Ай бұрын

  🛻💨💨💨👍

• 
  @JesseBlumАй бұрын

  @micron3268 I just blew my stocks tires. Omg haha. Was making a video and the tires just blew. I love this new motor setup

• 
  @polymetalalloyАй бұрын

  Sick runs. Were anything upgraded to the drivetrain?

• 
  @micron3268Ай бұрын

  Thanks, it's all stock. I haven't touched anything at all other than installing the electronics, foams!

• 
  @jamesonrcranch6753Ай бұрын

  I'm so amazed at how you guys do night runs 😢. Great pass 👌

• 
  @micron3268Ай бұрын

  Thanks!👍

• 
  @jamesonrcranch6753Ай бұрын

  @@micron3268 Welcome!! This is what it's about. #support

• 
  @TurtleRcАй бұрын

  Sick! Make me wanna do a night pass. Id have to set up better lights.

• 
  @micron3268Ай бұрын

  Thanks! Way less traffic👌

• 
  @skyhawk21Ай бұрын

  Oh oh… heavy breathing… intense…. Can you recommend lightweight red light like you use, to purchase local or online?

• 
  @m.p1976Ай бұрын

  Good Run🎉😊

• 
  @micron3268Ай бұрын

  Thank you.

• 
  @rct-i9896Ай бұрын

  Nice pass ,the night vid and your rc is cool af.Ithink i need those bsr foams on my 1/10 scale,i had Contact foams that turned me off using foams because they would chuck off pieces and cause the car to be uncontrollable.

• 
  @micron3268Ай бұрын

  Thanks man,👍 Give the bsr a try! 👍

• 
  @rct-i9896Ай бұрын

  @micron3268 i hope you dont mind sharing more info on the bsr foam specs.what is the shore number ,size of front and rear etc.?

• 
  @micron3268Ай бұрын

  @@rct-i9896 Not at all partner, the brand and part# is BSR F-3230-D and they are 70mm in diameter, 32mm wide and 30 shore. They fit without any modification. They have held up very well for me up to just under 150mph! They also make some with a diameter of 65mm that should hold up to more mph if you need. 👍

• 
  @rct-i9896Ай бұрын

  @micron3268 thank you,i appreciate you sharing. Expect a shout out from me in my video when i get those foams ,i gotta give credit where its due.

• 
  @micron3268Ай бұрын

  @@rct-i9896 Appreciate that, good luck bud! 👍

• 
  @mitchellminer4596Ай бұрын

  Nice pass buddy👊👍👍

• 
  @micron3268Ай бұрын

  Much appreciated!👊👍

• 
  @RcghostnrkАй бұрын

  Good job brother sounds good

• 
  @micron3268Ай бұрын

  Thanks, I appreciate that Ghost!👍

• 
  @MarkusKern-dp3jvАй бұрын

  Nice pass, the car has a lot of potential for higher speed.👍

• 
  @micron3268Ай бұрын

  Thanks buddy, fingers crossed I can push it to higher speeds!🤞

• 
  @scottbronson9738Ай бұрын

  I have a dual motor ak787 , and there is a yellow wire coming out of the main esc’s wires. This wire goes off into a small plug on each esc. From the videos I have seen they leave those two wires unplugged. Do you just leave those unplugged? Thanks your friend Scott 🏁🏁🏁

• 
  @micron3268Ай бұрын

  Sorry but I have never owned any Rlaarlo ESCs or electronics so I can't help you with that! Maybe ask on Rlaarlos Facebook page. Thanks for stopping in and taking a look!

• 
  @benabnjm4828Ай бұрын

  Nice pass I wish I had that road . Is that chaise one piece .

• 
  @micron3268Ай бұрын

  Thanks bud! Yes, it's a pretty nice road for sure! The Chassis is one piece including the front splitter, Its 3.5mm thick!

• 
  @benabnjm4828Ай бұрын

  @@micron3268 Thank you I was thinking of doing that now I will. 200 x 400 x 3 mm . Where do you get your sheets from .

• 
  @micron3268Ай бұрын

  @@benabnjm4828 I get them from Amazon. Yes, do it yourself just take your time and measure twice!🧐👍

• 
  @insanebmxthomasАй бұрын

  bruh i cant imagine my car going twice its current top speed. that's heroic!

• 
  @micron3268Ай бұрын

  Thanks man!

• 
  @benabnjm4828Ай бұрын

  Hi nice speed on 2s . I like your chaise looks 200 x 400 mil sheet is it 3 or 4 mil thick . I just got 3 sheets of 200 x 400 x 3 mil for my ak 917 s .

• 
  @micron3268Ай бұрын

  Thank you! This chassis is 240mm wide, 432mm long and 3.5mm thick! 👍

• 
  @JesseBlumАй бұрын

  So what esc do you have? I just upgraded to a 120amp but im not getting the speed tou are and i have a 4s 3300.ah 80c

• 
  @micron3268Ай бұрын

  Are you running stock tires or foams? What motor and specs, pinion gear? What is the battery brand and specs? All of that can affect your top speed!

• 
  @JesseBlumАй бұрын

  @micron3268 I am running stocks tires. But I was using a 27t pinion and really didn't like the results. I put in a 6500kv motor with a 20t pinion and Jesus christ this thing is a wild wild beast. And after four batteries of a 2,200 Mah 120 C I decided to finally try the 4S even though it wasn't recommended even though everyone said you shouldn't do it. I was checking my temps the whole time and nothing still got hot so from when I believe I think the reason people are overheating is cuz they're using way too large of a pinion.

• 
  @JesseBlumАй бұрын

  What amp do you have and did you do anything different with the gearing. I just put a 120amp esc on it

• 
  @micron3268Ай бұрын

  I have the 130amp spektrum esc in it with the spektrum 3200kv 3660 motor with a 35t pinion gear, I haven't touched anything on the truck except installing the electronics and tires and lowering the suspension! A 120amp esc should work great for you, good luck man👍

• 
  @JesseBlum16 күн бұрын

  @@micron3268 i used a 3652-3300kv last night I thought other was fast but this moved

• 
  @RcprescriptionАй бұрын

  Awesome pass! Car looks awesome!🤜🤛

• 
  @micron3268Ай бұрын

  Thank you!👍

• 
  @scottbronson9738Ай бұрын

  It’s just amazing what these cars can do!🏁🏁🏁

• 
  @mitchellminer4596Ай бұрын

  Great run buddy👊👍👍 Your excitement level has me laughing 🤣 I’d be freaking like a boy in the toy store😂

• 
  @micron3268Ай бұрын

  Thanks man, well at least your laughing! 🤪👍

• 
  @RcprescriptionАй бұрын

  Nice runs brother! 🤜🤛

• 
  @micron3268Ай бұрын

  Thanks for stopping in buddy!👍

• 
  @RlaarloАй бұрын

  It's too far away. Your eyesight is so good. I almost thought it wouldn't come back.

• 
  @micron3268Ай бұрын

  Thanks for taking a look!👍

• 
  @scottbronson9738Ай бұрын

  Great run! I love that paint job!🏁🏁🏁🏁

• 
  @micron3268Ай бұрын

  Thank you buddy! It's actually all tape on all my cars, I got a bit lazy on them! 🥱

• 
  @scottbronson9738Ай бұрын

  It looks great like that!🏁🏁🏁

• 
  @scaleworksRCАй бұрын

  Really nice stretch of road you have there.. nice clean pass and killer looking body! It's crazy to think that car was moving at 189 feet per second 🤯

• 
  @micron3268Ай бұрын

  Thanks bud! 👍

• 
  @djtazzmtlАй бұрын

  Btw do you have issues with the driveshaft cups?

• 
  @micron3268Ай бұрын

  I have not had any trouble with the truck so far! Thanks for stopping in!

• 
  @djtazzmtlАй бұрын

  I put the Hobbywing 4100KV (by mistake I thought I ordered the 3300KV) with high speed gear. God mode enabled haha

• 
  @micron3268Ай бұрын

  Warp speed for sure! Have fun!👍

• 
  @maxs6231Ай бұрын

  Just 4s? is that it

• 
  @micron3268Ай бұрын

  Yes, 4s is in it! Thanks for taking a look!

• 
  @maxs6231Ай бұрын

  @@micron3268 did you get the Spektrum 130amp Esc Spektrum 3660 3200kv motor from Amain Hobbies?

• 
  @maxs6231Ай бұрын

  @@micron3268 have you had any problems with the controller like I have?

• 
  @micron3268Ай бұрын

  @@maxs6231 I have never seen or used a Rlaarlo controller. This was the carbon roller so I'm using a Radiolink Rc4gs V3 controller and I do recommend Radiolink Rc4gs V3 or Rc6gs V3 for a low cost but very good controller if you end up needing something new!

• 
  @maxs6231Ай бұрын

  @@micron3268 Okay thanks I might do that.I Have the RTR carbon and the controller is just absolutely terrible.