Im here 5yrs later, was wondering why the end kept slipping, this explains it. Will try this in the morning. Good tip!
@eduardonaranjo9682Ай бұрын
Where did you purchase the door?
@greggfowler14432 ай бұрын
Thanks! Piece of cake!!
@SarinasandCo2 ай бұрын
Thanks for the video Eric!!!! Helped me alot, headed to the SB Merc to try those hoses - Arlo
@eschrader5 ай бұрын
Update- crank seal was butchered on the clutch side. Replaced with a new seal
@Lymeng256 ай бұрын
Experiencing the same thing my fuse relay and pump is good. Waiting on parts from FCP now thanks for the video
@thomps6s6 ай бұрын
Amazing, The tool would not line up due to the plastic tube, once I broke it the tube off, the tool went on the hoist, the spare came down and I am on the road again. Thanks a ton!
@alankelter94168 ай бұрын
Long story short, i know how to make those engines run from alot if exp on yz490s. Spent over 12yrs loving and perfecting my 02 kx500, chanced across a 92 wr500 one day. Put quick rebuild on engine w only a couple my old 490 tricks. Half ass went through suspension and dialed it in, (it was a side project didnt really care to much cause my k5 was my pride) put a very short amount of riding time on it.......scratched my head in complete disbelief of my findings. Sold my kx500. True story.
@cameronrich94888 ай бұрын
🙌 "Promo SM"
@Trailtested8 ай бұрын
That ending was a banger
@karloldroyd97710 ай бұрын
Had to do the same thing
@chiefwaz10 ай бұрын
Can you provide a link for the flywheel puller?
@eschrader10 ай бұрын
It was my dads, not sure where he got it but its old
@chiefwaz10 ай бұрын
I just started a JT2 MX project so please show more videos, I need help lol!
@eschrader10 ай бұрын
Good luck, I could never get it running right and sold it for $600. Not bad for a bike that starts but wouldnt have enough power to run.
@DariusBarazandeh10 ай бұрын
bro you did a great job. I am working on one here... kzread.info/dash/bejne/iHqkrqePpd3OeMY.html
@rcuniversespeed944711 ай бұрын
Head mod? Working on one myself
@eschrader8 ай бұрын
Just Garys mod by Eric Gorr. Some of the studs dont seem to go all the way through the nut so I might replace the studs as well for $75 or so.
@simonduckworth5941 Жыл бұрын
Very helpful - thanks! Quick question, when putting the new door on, did you somehow manage to put the door on in the closed position before reattaching the bolts holding it to the car? Many thanks
@eschrader Жыл бұрын
I think I just matched the paint marks on the hinge and put 1 bolt loose so I didn't have to pry the hinge open by hand from what I remember
@simonduckworth5941 Жыл бұрын
@@eschrader Good stuff! Thanks very much Eric 👍
@stephenromero1350 Жыл бұрын
Great content .. helpful even now
@johnkeiser6379 Жыл бұрын
Yea, thank you. I was confused about the arrows. Your video helped me very much. I appreciate your help.
@timothysiperly2403 Жыл бұрын
Damn cool it worked great!!! I was getting to cut the cable and didn't have to thank u very much !!
@HPTuchin Жыл бұрын
This video deserves more likes & views. Thank you.
@OJ9301 Жыл бұрын
The cabin air filter says down but the aftermarket air cabin filter is pointing up what should I do? Should I point the air filter down ?
@eschrader Жыл бұрын
That's what this video is about. Minute 2 talks about it. What aftermarket filter do you have and what words are around the arrow, such as up, down, airflow? Otherwise I would point the arrow down with your filter since it's probably indicating airflow direction.
@OJ9301 Жыл бұрын
@@eschrader my aftermarket STP has the arrow pointing up and says airflow but my Honda cabin has the arrow pointing down. So do I match the arrows? Even if my STP filter would be upside down ?
@HolstenSA Жыл бұрын
What will happen if the air flow arrow is flipped? Like i put it wrong it should be down but i put it up .
@eschrader Жыл бұрын
According to Google "If you install your filter in the wrong direction, air will have a hard time flowing through the filter's material and your air handler will have to work overtime to make up for the loss of airflow. This is not only a waste of energy, but it can also possibly damage your air conditioner or heating system"
@eschrader Жыл бұрын
6:30 to 13:00 is the assembly (the beginning was trial and error)
@eschrader Жыл бұрын
6 month update- hepa filter seems to have reduced the air output but it's kinda nice unless you run full blast a lot. Will probably be harder on the fan motor over time.
@DirtBagProdutions2 жыл бұрын
Thanks for sharing this.
@njsongwriter2 жыл бұрын
Good accurate video and you're right, a lot of folks are easily confused. However, there is one situation that you didn't cover... What if the filter brand you bought just had an arrow and it doesn't say "air flow" or "up" next to the arrow? Wix and NAPA filters are an example. The default with an air filter is that arrows on the edge of the filter point in the direction of air flow. So the only time an arrow on a horizontally mounted air filter points up is when it says up next to the arrow. I've confirmed this with an email from WIX. All horizontally mounted cabin air filters with the blower motor mounted below the filter will have downward air flow. If they had upward air flow then dirt and debris would be trapped inside the blower instead of collecting on top of the old filter. By the way, the STP brand does not have the words "up" or "air flow" next to the arrow, but when you point the arrow down the words will be upside down.
@eschrader2 жыл бұрын
Good catch! The correct text orientation should be the catch all. Do the arrows on the filters WITHOUT the word "airflow" all point up ⬆️?
@njsongwriter2 жыл бұрын
@@eschrader No. The only time they should point up is if it says "UP" next to the arrow. And as I said the STP filters will have the print upside down when you point the arrow down.
@eschrader2 жыл бұрын
@@njsongwriter I was thinking the edges tip of the paper filter needs to be at the top of the filter so the airflow pulls it down by suction to seal rather than the air forcing it to fold to the side allow air to bypass. That might also be another way to tell if that's what all the engineers design to.
@njsongwriter2 жыл бұрын
@@eschrader I think gravity is enough to keep it down. Actually there are two prongs on the back of the plastic cover that are designed to hold the air filter element up.
@moneymig2 жыл бұрын
That trick is not working for me right now it's kicking my ass
@eschrader2 жыл бұрын
You might have to crawl under and see what shape the square is to get a good fit. Also some other videos say to let the air out of the tire incase it's wedged in there good, and I think there's a few other tips in those videos. Good luck!
@moneymig2 жыл бұрын
@@eschrader I tried n tried , I think it's just old as shit , very frustrating , thanks
@eschrader2 жыл бұрын
@@moneymig when I couldn't get mine down, I bought a tire and rim off Craigslist for like $30. Crap tire but I was able to drive it at least.
@cg55623 жыл бұрын
Yep spent half an hr and this solved it. Truck will run for 300k but I cant change the tire!!! Many thanks
@waterman16683 жыл бұрын
Great info thanks
@bryanyoutubechannel3 жыл бұрын
It helped a lot, thank you!!!
@wildbob86503 жыл бұрын
Eric THANK YOU SO MUCH for this video! You saved my ass! Love ya man!
@jacobstelmaszewski78054 жыл бұрын
Where did you find the points?
@eschrader4 жыл бұрын
Ebay but rockymountainatvmc.com OEM parts has them
@jacobstelmaszewski78054 жыл бұрын
@@eschrader Thank you
@hunterbenson73504 жыл бұрын
What type of oil do you use in it
@eschrader4 жыл бұрын
Yamalube 2s I think but I would have to check
@hunterbenson73504 жыл бұрын
@@eschrader is that what you use in the gearbox
@eschrader4 жыл бұрын
@@hunterbenson7350 yamalube transmission oil plus www.yamaha-motor.ca/eshop/detail.php?sectionId=YL&groupId=17&subGroupId=14&categoryId=63&itemId=2910
@jamesrivera28485 жыл бұрын
Thanks Buddy after workin with it for about two hours I just went on KZread and just follow your direction thanks
@eschrader5 жыл бұрын
Yea I am so gun shy I still havent put the new spare back up there.
@brystonfranke16915 жыл бұрын
where did you buy that puller?
@imtryingtosleep89355 жыл бұрын
you need to stand up
@eschrader5 жыл бұрын
Butt in the saddle gets better grip. I got a taller seat that made standing up easier. Watch some other racing videos of mine, got a bit faster.
@eschrader6 жыл бұрын
Part 2 kzread.info/dash/bejne/i2aOpMGJZM2tpLQ.html
@eschrader6 жыл бұрын
Part 1 kzread.info/dash/bejne/eYWCs8yYj9jfl7w.html
@Xomanowar996 жыл бұрын
278 k miles! . . . Wow!
@eschrader6 жыл бұрын
290k now
@eschrader6 жыл бұрын
I am starting to save for a new truck. Dont think this puppy will hold together another year but we will see!
@miguellozano89366 жыл бұрын
The 1&2 blower speeds not working could be the blower motor resistor being bad. Sometimes wires are burnt on it.
@eschrader6 жыл бұрын
I think so too, I have a new one in my cart on Amazon, just haven't pulled the trigger yet. Checked my engine codes and its just some smog stuff.
@eschrader6 жыл бұрын
Yup, $36 on Amazon www.amazon.com/gp/product/B007Q1K6EQ and it works great now. Also replaced the two cabin filters that had tons of pine needles and were caked with dirt. Cabin Filter $19 www.amazon.com/gp/product/B0010DW5ZO
@eschrader6 жыл бұрын
Update now that it's been a few months. The lights have only came on and off once or twice while going down bump washboard dirt roads. So there might be a second ground issue somewhere but at least im not worried about an airbar flying out at my face when driving down the freeway anymore.
@Immj2077 жыл бұрын
I enjoyed this video. Nice job.
@jcozine7 жыл бұрын
Nice vid! I was the one two to the left of you that wheelied all the way down the start straight. Great battling with you!
@kurtisbaker57857 жыл бұрын
jcozine nice start man wheeling all the way down! that KTM was pulling on my honda for sure!
@kurtisbaker57857 жыл бұрын
good ride man!
@blakehoward45387 жыл бұрын
good racing! I was on the Husky to your right on the start. V117. see ya at Taft
@eschrader7 жыл бұрын
Blake Howard great race! Taft is do dang cold in the morning. last year I almost froze in a tent at night, was not a happy camper
Пікірлер
Way too long to change that filter
Im here 5yrs later, was wondering why the end kept slipping, this explains it. Will try this in the morning. Good tip!
Where did you purchase the door?
Thanks! Piece of cake!!
Thanks for the video Eric!!!! Helped me alot, headed to the SB Merc to try those hoses - Arlo
Update- crank seal was butchered on the clutch side. Replaced with a new seal
Experiencing the same thing my fuse relay and pump is good. Waiting on parts from FCP now thanks for the video
Amazing, The tool would not line up due to the plastic tube, once I broke it the tube off, the tool went on the hoist, the spare came down and I am on the road again. Thanks a ton!
Long story short, i know how to make those engines run from alot if exp on yz490s. Spent over 12yrs loving and perfecting my 02 kx500, chanced across a 92 wr500 one day. Put quick rebuild on engine w only a couple my old 490 tricks. Half ass went through suspension and dialed it in, (it was a side project didnt really care to much cause my k5 was my pride) put a very short amount of riding time on it.......scratched my head in complete disbelief of my findings. Sold my kx500. True story.
🙌 "Promo SM"
That ending was a banger
Had to do the same thing
Can you provide a link for the flywheel puller?
It was my dads, not sure where he got it but its old
I just started a JT2 MX project so please show more videos, I need help lol!
Good luck, I could never get it running right and sold it for $600. Not bad for a bike that starts but wouldnt have enough power to run.
bro you did a great job. I am working on one here... kzread.info/dash/bejne/iHqkrqePpd3OeMY.html
Head mod? Working on one myself
Just Garys mod by Eric Gorr. Some of the studs dont seem to go all the way through the nut so I might replace the studs as well for $75 or so.
Very helpful - thanks! Quick question, when putting the new door on, did you somehow manage to put the door on in the closed position before reattaching the bolts holding it to the car? Many thanks
I think I just matched the paint marks on the hinge and put 1 bolt loose so I didn't have to pry the hinge open by hand from what I remember
@@eschrader Good stuff! Thanks very much Eric 👍
Great content .. helpful even now
Yea, thank you. I was confused about the arrows. Your video helped me very much. I appreciate your help.
Damn cool it worked great!!! I was getting to cut the cable and didn't have to thank u very much !!
This video deserves more likes & views. Thank you.
The cabin air filter says down but the aftermarket air cabin filter is pointing up what should I do? Should I point the air filter down ?
That's what this video is about. Minute 2 talks about it. What aftermarket filter do you have and what words are around the arrow, such as up, down, airflow? Otherwise I would point the arrow down with your filter since it's probably indicating airflow direction.
@@eschrader my aftermarket STP has the arrow pointing up and says airflow but my Honda cabin has the arrow pointing down. So do I match the arrows? Even if my STP filter would be upside down ?
What will happen if the air flow arrow is flipped? Like i put it wrong it should be down but i put it up .
According to Google "If you install your filter in the wrong direction, air will have a hard time flowing through the filter's material and your air handler will have to work overtime to make up for the loss of airflow. This is not only a waste of energy, but it can also possibly damage your air conditioner or heating system"
6:30 to 13:00 is the assembly (the beginning was trial and error)
6 month update- hepa filter seems to have reduced the air output but it's kinda nice unless you run full blast a lot. Will probably be harder on the fan motor over time.
Thanks for sharing this.
Good accurate video and you're right, a lot of folks are easily confused. However, there is one situation that you didn't cover... What if the filter brand you bought just had an arrow and it doesn't say "air flow" or "up" next to the arrow? Wix and NAPA filters are an example. The default with an air filter is that arrows on the edge of the filter point in the direction of air flow. So the only time an arrow on a horizontally mounted air filter points up is when it says up next to the arrow. I've confirmed this with an email from WIX. All horizontally mounted cabin air filters with the blower motor mounted below the filter will have downward air flow. If they had upward air flow then dirt and debris would be trapped inside the blower instead of collecting on top of the old filter. By the way, the STP brand does not have the words "up" or "air flow" next to the arrow, but when you point the arrow down the words will be upside down.
Good catch! The correct text orientation should be the catch all. Do the arrows on the filters WITHOUT the word "airflow" all point up ⬆️?
@@eschrader No. The only time they should point up is if it says "UP" next to the arrow. And as I said the STP filters will have the print upside down when you point the arrow down.
@@njsongwriter I was thinking the edges tip of the paper filter needs to be at the top of the filter so the airflow pulls it down by suction to seal rather than the air forcing it to fold to the side allow air to bypass. That might also be another way to tell if that's what all the engineers design to.
@@eschrader I think gravity is enough to keep it down. Actually there are two prongs on the back of the plastic cover that are designed to hold the air filter element up.
That trick is not working for me right now it's kicking my ass
You might have to crawl under and see what shape the square is to get a good fit. Also some other videos say to let the air out of the tire incase it's wedged in there good, and I think there's a few other tips in those videos. Good luck!
@@eschrader I tried n tried , I think it's just old as shit , very frustrating , thanks
@@moneymig when I couldn't get mine down, I bought a tire and rim off Craigslist for like $30. Crap tire but I was able to drive it at least.
Yep spent half an hr and this solved it. Truck will run for 300k but I cant change the tire!!! Many thanks
Great info thanks
It helped a lot, thank you!!!
Eric THANK YOU SO MUCH for this video! You saved my ass! Love ya man!
Where did you find the points?
Ebay but rockymountainatvmc.com OEM parts has them
@@eschrader Thank you
What type of oil do you use in it
Yamalube 2s I think but I would have to check
@@eschrader is that what you use in the gearbox
@@hunterbenson7350 yamalube transmission oil plus www.yamaha-motor.ca/eshop/detail.php?sectionId=YL&groupId=17&subGroupId=14&categoryId=63&itemId=2910
Thanks Buddy after workin with it for about two hours I just went on KZread and just follow your direction thanks
Yea I am so gun shy I still havent put the new spare back up there.
where did you buy that puller?
you need to stand up
Butt in the saddle gets better grip. I got a taller seat that made standing up easier. Watch some other racing videos of mine, got a bit faster.
Part 2 kzread.info/dash/bejne/i2aOpMGJZM2tpLQ.html
Part 1 kzread.info/dash/bejne/eYWCs8yYj9jfl7w.html
278 k miles! . . . Wow!
290k now
I am starting to save for a new truck. Dont think this puppy will hold together another year but we will see!
The 1&2 blower speeds not working could be the blower motor resistor being bad. Sometimes wires are burnt on it.
I think so too, I have a new one in my cart on Amazon, just haven't pulled the trigger yet. Checked my engine codes and its just some smog stuff.
Yup, $36 on Amazon www.amazon.com/gp/product/B007Q1K6EQ and it works great now. Also replaced the two cabin filters that had tons of pine needles and were caked with dirt. Cabin Filter $19 www.amazon.com/gp/product/B0010DW5ZO
Update now that it's been a few months. The lights have only came on and off once or twice while going down bump washboard dirt roads. So there might be a second ground issue somewhere but at least im not worried about an airbar flying out at my face when driving down the freeway anymore.
I enjoyed this video. Nice job.
Nice vid! I was the one two to the left of you that wheelied all the way down the start straight. Great battling with you!
jcozine nice start man wheeling all the way down! that KTM was pulling on my honda for sure!
good ride man!
good racing! I was on the Husky to your right on the start. V117. see ya at Taft
Blake Howard great race! Taft is do dang cold in the morning. last year I almost froze in a tent at night, was not a happy camper
good video man