REPAIR and maintenance on chainsaws, weed trimmers, pole saws, hedge trimmers, blowers, edgers, and about any other 2 cycle equipment. Find our contact info on our Facebook Page under "Lester Olive In The Shop "
What size machine screw was used to pull the limiters? Thanks
@jamesdalme82462 күн бұрын
These stihl pole saws are the biggest pieces of shit I’ve ever seen . One branch falls wrong is all it takes to bend the flimsy top pole and flimsy driveshaft. It Only costs around $3-400 in parts to repair it. But hey my ht101 engine still runs. I’ll stick with echo from now on.
@JFHedgeTrimmingLtd2 күн бұрын
Awesome video! Thank you for sharing! Cheers
@philliphall51984 күн бұрын
Really it’s best to keep them dry and out of the weather 😢 It’s a common problem 😅
@EPHONIC4 күн бұрын
Awesome video. Love how you explain each step and why things are to be done a certain way. Great job! Liked the video!
@miguelruiz14925 күн бұрын
By far best video ive seen thank you 💪
@pmventura416 күн бұрын
Definitely interesting to know. Thank You.
@vinnyp909313 күн бұрын
By far the BEST video on the HT 101 Not only did I get it back together I also understand how all the components work together now! This thing is tricky and Lester simplifies it better than no other! Appreciate you Lester
@al5226914 күн бұрын
Great video. Straight to the point. Thanks for sharing New subscriber here
@yl148714 күн бұрын
Have their top battery machine, as of 2024, 540 iXP. Great power. Great in this regard. Chain tensioner mechanism drives me nuts. Essentially same as this. Keeps slipping, loosening, chain goes slack far too early after re-tension. Can see nub turn! No chain isn't stretching, yes am familiar with chain mounting fundamentals: lift bar nose up when tightening side cover - pointed the above out each time matter is discussed. Any solutions? Chalk brushed into tensioner thread perhaps?
@philippe764717 күн бұрын
Good job, thanks 👍🏻
@AntonioCastillo-qs9qf19 күн бұрын
Awesome thanks
@lukehouser931721 күн бұрын
My spline keeps separating, almost like the cover over the spline isn’t staying put. Any suggestions?
@MudaMotorsport25 күн бұрын
Very nice video. Bought one the other day. Muck in the valve . Easy fix with your vid. Thank you!
@jorgenolazco874225 күн бұрын
Would that somehow cause vibrations on my shaft. On my pas 225?
@luckydog-28725 күн бұрын
Very nice! Thank you!
@user-yk4xu4qq4pАй бұрын
Thank you for the advice 👍👍
@garyconrad578Ай бұрын
This is my first comment ever. Lester, your combination of great video and great explanation is so helpful! You are a born teacher/trainer. Concise, accurate and documented with perfect video! Thank you so much!!!
@atozeqАй бұрын
Excellent video-a great help replacing bent outer black shaft housing-Thanks
@frankiecarroll2235Ай бұрын
I have a Stihl ht 56c want to upgrade from 10 inch bar and chain to the 12 inch bar and chain . It has the pico 1/4 sprocket what part number is the 3/8 speocket . And how many washers wil i need
@IsmaelHernandez-BolasАй бұрын
I replaced mine and it doesn't change at all. It has a roll pin that only allows 1/4 turn. I removed the pin to try to close the flow and the whole adjuster comes loose. I tried 8 different amounts of turns and it still oils excessively.
@jamesstanley5503Ай бұрын
Outstanding tutorial Lester. Thanks for posting and saving me so much time from having to figure it out what's inside these Stihl poles with no insight. cheers
@michaelmason9784Ай бұрын
Informative but bad camera angle
@franciscoortiz3575Ай бұрын
Will it work on a battery operated Ryobi?
@SteveThramannАй бұрын
Thank You!! I may try to use gloves again when working on small parts just because you seem to navigate well with them. Very clear instructions.
@rosseowensАй бұрын
Awesome!! Thanks bro!
@MsAknesАй бұрын
Thank you! This is exactly what we needed after trying to assemble the trimmer for 2 hours 😂
@HowleebraАй бұрын
My Echo SRM 225 runs like a BEAST for about 15 minutes and then boggs right out... if I let it sit for about 20min I can repeat the process however it always seems to "choke" out. It'll restart immediately but the moment I hit anywhere near half throttle it starts to choke even though it ran perfectly normal up till then... lower mid-range seem to function but the moment you get anywhere near the high end of the throttle it just drowns once it's good and hot I've replaced the fuel delivery system, cleaned the carburetor, changed the spark plug and kept her topped off with fuel plus of course always kept a nice clean air filter... I build gas RC cars, ride Motor Cross Bikes and have Decades of experience maintaining chainsaws, lawn mowers and all types of gas powered equipment yet I've never seen anything quite like this... I guess the next thing I'm going to try is to completely swap out with a new carburetor? I bought her new and never had a problem for about 7 years of residential use🤔
@foreman8259Ай бұрын
С трудом нашёл это видео. Возникла проблема с заменой топливного фильтра бензокосы STIHL FS 90. Благодарность за подробное описание.
@garyshwinthorpe1050Ай бұрын
Was working at my shop and that tab broke off for the connector, I didn’t know what to do but this helped a lot. Thank you so much.
@faysalkalayaf8395Ай бұрын
You saved my machine. I was about to buy new one. I really appreciate your time.
@ghengis5410Ай бұрын
How do you get the primer bulb out?
@med1pilot1956Ай бұрын
You just saved me a trip to the shop and the fees that go with it. This pump failed once before several years ago. I lost a week while it was in the shop and I forget how much it cost. Thank you
@stevegosnell4058Ай бұрын
Now a great straightforward no bullshit video great job.
@cma81652 ай бұрын
Mr. Lester Olive In The Shop: Thank you very much for your video. It was certainly very useful, informative, and valuable to me cause following your advice I was able to fix my Stihl FS90R weed trimmer and now it runs like new again! Please keep your videos coming cause they save me lots of labor fees.
@alandust21882 ай бұрын
Much better, couldn't ask for a better video...thanks.
@morethanenough72 ай бұрын
This was a great help to me. I realized through watching that I was also missing a gasket. Thank you.
@alandust21882 ай бұрын
Much better.....Thanks!
@justinsta2 ай бұрын
This might be the best filmed and best explained video I've seen on KZread! Thank you so much for clearly explaining how and why your doing what you need to do.
@squirrelcovers63402 ай бұрын
$60😠😂😂😂😂😂😂
@squirrelcovers63402 ай бұрын
"Barrier bars"😂 😂😂 are a joke. That blade is garbage.
@Paul-iu1om2 ай бұрын
Terrific video very detailed but audio hard to hear you
@JulieTerstriep2 ай бұрын
You did an EXCELLENT job! I'll be looking for your videos for repairs of other pieces of equipment....Stihl brush cutter, etc! Thank you so much!
@JhonattanRamirez-tu7jc2 ай бұрын
Can it be used without the blade?
@reedallidap71732 ай бұрын
Great video. I had the opposite happen. The connecting piece on my hedge trimmer attachment sticks out too much and won’t slide in. Any videos on how I can fix that?
@justinedwards40462 ай бұрын
Thank you sir! Got me out of a bind.
@magicone93272 ай бұрын
The bigger sprocket diameter will give you a higher chain speed, not so much torque. Think of putting your truck in 5 th gear and start up a hill vs 1 st gear which one will get you to the top fab steep hill?
@theresahoffman84082 ай бұрын
NICE!!. Thats what i was looking for. I wanted to not use the million dollar grease but didnt know how to thoroughly get grease down, in there. Didn't think about tossing a zerk fitting in there. Stihl Head is Metric, 10x1.5 pitch threads.
@MommyORdaddy2 ай бұрын
Just paid $125 to get lightly used one fixed! Clean… just used it n LOVE IT 😅
Пікірлер
You didn't tighten the clutch when reinstalling
What size machine screw was used to pull the limiters? Thanks
These stihl pole saws are the biggest pieces of shit I’ve ever seen . One branch falls wrong is all it takes to bend the flimsy top pole and flimsy driveshaft. It Only costs around $3-400 in parts to repair it. But hey my ht101 engine still runs. I’ll stick with echo from now on.
Awesome video! Thank you for sharing! Cheers
Really it’s best to keep them dry and out of the weather 😢 It’s a common problem 😅
Awesome video. Love how you explain each step and why things are to be done a certain way. Great job! Liked the video!
By far best video ive seen thank you 💪
Definitely interesting to know. Thank You.
By far the BEST video on the HT 101 Not only did I get it back together I also understand how all the components work together now! This thing is tricky and Lester simplifies it better than no other! Appreciate you Lester
Great video. Straight to the point. Thanks for sharing New subscriber here
Have their top battery machine, as of 2024, 540 iXP. Great power. Great in this regard. Chain tensioner mechanism drives me nuts. Essentially same as this. Keeps slipping, loosening, chain goes slack far too early after re-tension. Can see nub turn! No chain isn't stretching, yes am familiar with chain mounting fundamentals: lift bar nose up when tightening side cover - pointed the above out each time matter is discussed. Any solutions? Chalk brushed into tensioner thread perhaps?
Good job, thanks 👍🏻
Awesome thanks
My spline keeps separating, almost like the cover over the spline isn’t staying put. Any suggestions?
Very nice video. Bought one the other day. Muck in the valve . Easy fix with your vid. Thank you!
Would that somehow cause vibrations on my shaft. On my pas 225?
Very nice! Thank you!
Thank you for the advice 👍👍
This is my first comment ever. Lester, your combination of great video and great explanation is so helpful! You are a born teacher/trainer. Concise, accurate and documented with perfect video! Thank you so much!!!
Excellent video-a great help replacing bent outer black shaft housing-Thanks
I have a Stihl ht 56c want to upgrade from 10 inch bar and chain to the 12 inch bar and chain . It has the pico 1/4 sprocket what part number is the 3/8 speocket . And how many washers wil i need
I replaced mine and it doesn't change at all. It has a roll pin that only allows 1/4 turn. I removed the pin to try to close the flow and the whole adjuster comes loose. I tried 8 different amounts of turns and it still oils excessively.
Outstanding tutorial Lester. Thanks for posting and saving me so much time from having to figure it out what's inside these Stihl poles with no insight. cheers
Informative but bad camera angle
Will it work on a battery operated Ryobi?
Thank You!! I may try to use gloves again when working on small parts just because you seem to navigate well with them. Very clear instructions.
Awesome!! Thanks bro!
Thank you! This is exactly what we needed after trying to assemble the trimmer for 2 hours 😂
My Echo SRM 225 runs like a BEAST for about 15 minutes and then boggs right out... if I let it sit for about 20min I can repeat the process however it always seems to "choke" out. It'll restart immediately but the moment I hit anywhere near half throttle it starts to choke even though it ran perfectly normal up till then... lower mid-range seem to function but the moment you get anywhere near the high end of the throttle it just drowns once it's good and hot I've replaced the fuel delivery system, cleaned the carburetor, changed the spark plug and kept her topped off with fuel plus of course always kept a nice clean air filter... I build gas RC cars, ride Motor Cross Bikes and have Decades of experience maintaining chainsaws, lawn mowers and all types of gas powered equipment yet I've never seen anything quite like this... I guess the next thing I'm going to try is to completely swap out with a new carburetor? I bought her new and never had a problem for about 7 years of residential use🤔
С трудом нашёл это видео. Возникла проблема с заменой топливного фильтра бензокосы STIHL FS 90. Благодарность за подробное описание.
Was working at my shop and that tab broke off for the connector, I didn’t know what to do but this helped a lot. Thank you so much.
You saved my machine. I was about to buy new one. I really appreciate your time.
How do you get the primer bulb out?
You just saved me a trip to the shop and the fees that go with it. This pump failed once before several years ago. I lost a week while it was in the shop and I forget how much it cost. Thank you
Now a great straightforward no bullshit video great job.
Mr. Lester Olive In The Shop: Thank you very much for your video. It was certainly very useful, informative, and valuable to me cause following your advice I was able to fix my Stihl FS90R weed trimmer and now it runs like new again! Please keep your videos coming cause they save me lots of labor fees.
Much better, couldn't ask for a better video...thanks.
This was a great help to me. I realized through watching that I was also missing a gasket. Thank you.
Much better.....Thanks!
This might be the best filmed and best explained video I've seen on KZread! Thank you so much for clearly explaining how and why your doing what you need to do.
$60😠😂😂😂😂😂😂
"Barrier bars"😂 😂😂 are a joke. That blade is garbage.
Terrific video very detailed but audio hard to hear you
You did an EXCELLENT job! I'll be looking for your videos for repairs of other pieces of equipment....Stihl brush cutter, etc! Thank you so much!
Can it be used without the blade?
Great video. I had the opposite happen. The connecting piece on my hedge trimmer attachment sticks out too much and won’t slide in. Any videos on how I can fix that?
Thank you sir! Got me out of a bind.
The bigger sprocket diameter will give you a higher chain speed, not so much torque. Think of putting your truck in 5 th gear and start up a hill vs 1 st gear which one will get you to the top fab steep hill?
NICE!!. Thats what i was looking for. I wanted to not use the million dollar grease but didnt know how to thoroughly get grease down, in there. Didn't think about tossing a zerk fitting in there. Stihl Head is Metric, 10x1.5 pitch threads.
Just paid $125 to get lightly used one fixed! Clean… just used it n LOVE IT 😅