Пікірлер

• 
  @ayanabell69818 сағат бұрын

  What position should my multi meter be set to?

• 
  @mostafafarhidzadeh5943 күн бұрын

  What about rekey?!I have a kenmore France ( three doors) not cooling , what is the problem. Fans of both codes or and evaporator and compressor are working .

• 
  @mjmej47348 күн бұрын

  That's ground not neutral

• 
  @chadmiller273712 күн бұрын

  Thank you! I know this was posted years ago, but it’s still helping people!

• 
  @morganwilson186714 күн бұрын

  What if my compressor clicks on and off. It runs for a few seconds and clicks off for a few minutes. It’s also wicked hot! Is it worth trying this or considering the compressor a loss??

• 
  @JohnDoe-up1us14 күн бұрын

  Great, Great Video. It is people like you that helps millions of people save money. I am surprised there is not a million likes. You have helped me with my whirlpool. As a renter who has to pay for washer/dryer maintenance, thos is a game changer. I urge all renters and home owner to watch this video

• 
  @davidedwards438715 күн бұрын

  Great video. We were overseas and our dryer went out on our daughter. We were gone for 1 week out of a 6 month trip when it happened. I ended up buying a new Amana from Lowes to get a working dryer again. We just returned and the new Amana just started not drying. It worked for less than 4 months, Amana is sending out a repairman. The old Roper is in my basement. They kept for me to look at when I returned. With the new dryer acting up, I decided to see what was wrong with the old Roper. I have checked everything you mentioned except for the voltage at the wall. It all checks out fine. The issue is it will stop drying after 5 minutes or so. I am leaning towards the timer being the issue and possibly corrosion in the contacts. There was a decent amount of lint in the upper area near the timer. If the contacts are dirty this might be the issue.. Any thoughts?

• 
  @JayGoodwin-i6k15 күн бұрын

  I think yours is the best and most informative repair video I have seen. Thank you for making it. I did not determine my problem, but I will continue to search.

• 
  @lauragraham129416 күн бұрын

  You saved me a repair man call!! Thank you!!!!

• 
  @fullmetalfunk16 күн бұрын

  i had to take apart my dryer and fix it today (it was the timer) thank you for this video! it really helped me out!

• 
  @deborahday845319 күн бұрын

  Dryer works but has burning smell

• 
  @atrueamerican221822 күн бұрын

  Thanks for the help. Mine is fixed because of you.

• 
  @xRysen22 күн бұрын

  This helped solve my problem in 2024! Thanks so much!

• 
  @sd778724 күн бұрын

  Awesome video, no crappy music or computer generated voice stating the obvious just pure facts and knowledge from a real expert. Check the timer!!! Every other video leaves that out! Best Dryer fix KZread video by far, Byrd is the word!

• 
  @wtfyoguylolАй бұрын

  Excellent video, my dryer needed a timer. Thank you very much 👊

• 
  @ThomasRameetse-xc7rwАй бұрын

  Thanks very much for teaching washing machine for today

• 
  @armstrong5722Ай бұрын

  What if I don’t hear the clicking sound? Compressor is hot, fan is on.

• 
  @oliviaq4722Ай бұрын

  After watching the video I was able to successfully fix the agitator. You saved me hundreds of dollars!!! THANK YOU SO MUCH!

• 
  @QueenTut.Ай бұрын

  What if the heating element has no power? But everything else is fine?

• 
  @imaxfliАй бұрын

  They always show the easy fixes.......my couplers good. It will fill and then do nothing. Its not the pump.

• 
  @imaxfliАй бұрын

  Mine fills then does nothing...can hear slight buzz? Any ideas????

• 
  @debbiecastro8370Ай бұрын

  My washing machine is not agitating. It was making a humming noise. Now it is doing nothing. The sensing fill light is blinking.

• 
  @joeyskullz3331Ай бұрын

  Went through all the steps , got continuity on all points. Assumed motor was burned out. Plugged it back in pulled off the start knob by accident pushed the protruding pin and she fired up 😅. Stuffed a little piece of tin foil in the start knob cavity to take up extra space and the dryer works like day one. Oh well, at least I learned what to look for in the future. Video deserves multiple thumbs up

• 
  @justinneilsonn2665Ай бұрын

  I cant get the bolt to budge

• 
  @bbraskyАй бұрын

  Thanks. I had a guy replace my belt(s) and it still didn't work (although no burning rubber smell, they did need change). Was kinda upset, but this looks easy - will give it a shot. I'm not mad at him, but he shoulda waited longer and ran it thru the cycles though.

• 
  @narutowindelАй бұрын

  THANK YOU, was a door switch

• 
  @anthonyrippo8518Ай бұрын

  my start or run capacitor is located near the motherboard. do i take it out?

• 
  @syedpervez7009Ай бұрын

  Thanks 👍

• 
  @RobertDelahayeАй бұрын

  So I got a question and your video was the closest I could find that showed any type of help. So washer stopped working, no power, ended up being control board. Repair man came out and replaced the control board, said it didnt work he then said i had to get a new washer. but when i looked into it he hooked it up all wrong. After I hooked it up correctly it started working. Ran a quick cycle to test it out and half way through it stopped working again and once again now power. After testing around it was that fuse that is blown. While it looks fairly easy to replace that fuse, something keeps blowing it, and I dont know where else to look. There are not any youtube video with this issue on my washer and the internet isnt really helping, just says replace the control board. but if it has blown two fuses, then its pointless to replace unless i can determin where the issue is coming from. Any suguestions? Whirlpool WFW5620HW0 4 years old

• 
  @Amanda-uq7ylАй бұрын

  Thank you sir!

• 
  @sidhartha4397Ай бұрын

  at about 2:00 he starts manipulating with the screwdriver. clockwise or counterclockwise? hard to tell.

• 
  @kshisslerАй бұрын

  Thank you so much for the video! So helpful. Hopefully Samsung can fix this problem!

• 
  @tammyhall1008Ай бұрын

  I’ve been reading the comments and boy I wish some of you men lived by me to help me out with my dryer not heating..it kills me to have to pay top notch for an actual appliance guy😢I’m on a fixed income..

• 
  @breakingbadheisenberg97032 ай бұрын

  Mines humming?

• 
  @ZteveW2 ай бұрын

  What do you think about that spray that converts rust into a paintable surface like Rustoleun's Rust Reformer? Could that work?

• 
  @301Geo2 ай бұрын

  Thank you for the video! Fixed my kenmore washer for $6 😊

• 
  @thesetruths14042 ай бұрын

  Hi there. This is what I have, does it indicate a bad relay? Whirlpool WRT111SFDW03. 7 years old. 11.2 cu ft size. Freezer on top. Start relay P/N: WPW10448874, aka W10448874. Capacitor ("cap") P/N: WPW10662129 Test relay connections with capacitor on the relay. Results: when together I can get cap to charge and discharge thru the start relay, just like it does when it's off the relay. With cap off and on, neither of the lower holes have continuity with each other. The hole on lower left has 0.0 ohms resistance thru the bottom blade of the back of the plug. The lower right hole has no continuity with anything but can be used to charge the capacitor for testing. The upper hole has 0.1 ohm resistance to the top blade on the opposite side. Remove relay cover and visually check. I cannot get combination relay apart without breaking it, so I haven't committed to that, yet. Ohm test the fridge compressor pins again. Make sure the Common (top) and lower pins are within 3 ohms. And the two pins at bottom should read about the sum of the Common with the Start and Run pins. See KZread video... Results: Top and Lower Right : 4.4 ohm. Top to Lower Left: 6.0 ohm. Two bottom pins: 10.4 ohm. None of the pins are shorted to ground. My problem is it suddenly stopped cooling without noises or warning, but I caught it from hearing loud buzzing noise from compressor and relay area, and compressor was very hot. No smoke or smells though, and wires did not seem to be hot. Do you think it's the combination relay? Thank ya!

• 
  @zac70622 ай бұрын

  2021 GE Washer Model WCSR2090D5WW

• 
  @chrisfalx32512 ай бұрын

  Should I order the DD dollar spindle? Should I order the $15 clutch thingy from the bottom or do I get done white rotor looking thing or should I just drop 400 bucks on everything and potentially still not fix it😢

• 
  @mattstringham50562 ай бұрын

  Thank you! I found the issue and repaired the problem with a $5 part. Saved me a ton of time and money.

• 
  @michelleeigsti88592 ай бұрын

  Thanks! I was able to figure out my heat sensor was bad from this video. I had changed out my heating element after it broke only for it to not work long and it quit heating again. I did the tests and was so glad to find it was an easy fix

• 
  @SubZero-pl9lv2 ай бұрын

  Does this machine not take an igniter?

• 
  @rdffremn62202 ай бұрын

  Did you replace those little four little things in that agitator that have the teeth or did you just clean them and put those back in there

• 
  @BonnieRae-lv4jr2 ай бұрын

  compressor is hot

• 
  @carlthornton30762 ай бұрын

  Very Good!... #271 {5-20-2024}

• 
  @Dennisjp-83182 ай бұрын

  ty

• 
  @TheNYgolfer2 ай бұрын

  The cycling thermostat is the one next to the thermal fuse. It has 4 wires. The thermostat by the heater terminals is a high limit thermostat and only cycles if the cycling thermo fails to open.

• 
  @dfautomaton3 ай бұрын

  Thanks! This helped me fix my ancient Kenmore. Here's to another 35 years

• 
  @mariagrazia52323 ай бұрын

  My Miele W5872 111 edition has a little oscillation of the inner drum, just milimeters. I mean it does not run 100% parallel to the outer drum and the rubber seal (does not touch it anyway), but has no weird spin noises at all and no vertical or horizontal movement if you try to pull or push, there is no looseness, it is just like if the drum is slightly distorted, but works perfectly. Does this have any sense? If it's the damm spider, how much time can take to get destroyed? I've done a total flush 95ªC with vinegar and baking soda to remove any soap or mold rest and always keep the door open after each cycle.

• 
  @SojournerLands3 ай бұрын

  I have checked everything and continuity and resistance checkout. I have voltage at the main cable. Thermostat, fuse, temp select switch are all functioning correctly. It still feels like the dryer is not getting hot enough. Could it be the heating element that needs to be replaced?