Need ur help I have a vz 05 5.7liter 6speed sedan car ran then stops so chanced fule fitter it runs an lease than 2 or 5 seconds stops running wood my fule pump have shit it self
@downtheshedwithbyronКүн бұрын
Gday mate Now im guessing youve got fuel that the filter is on the right way and can you hear the pump prime before you try and start it?
@darren58513 минут бұрын
@downtheshedwithbyron yes it primes runs then lease the 5 seconds later shuts down
@svndays4 күн бұрын
Cheers mate just did this on a Volvo S40 and the low end power is back once again.
@downtheshedwithbyron3 күн бұрын
Awesome mate
@marcosoto41644 күн бұрын
Thanks a lot real help
@downtheshedwithbyron4 күн бұрын
No dramas mate 👍
@user-bm4kc7rr5h4 күн бұрын
Cheers mate love the video it was awesome, now after watching your video im all set to do mine and now im getting the run about on which is rhe correct service kit, repco has 3 kits stating they fit my vehicle, but i dont think any of them do, im only planning on using a repco or ryco kit ( quality kit) do you still have the part number for your kit you used? Thanks mate keep up the good work
@downtheshedwithbyron4 күн бұрын
Thanks mate 👍 Sorry i did this job i think 4 years ago it would of been a ryco kit
@armitage277 күн бұрын
About to do this with my 2001 wh grange 🎉
@downtheshedwithbyron7 күн бұрын
Sweet dude 👌
@robirvine29227 күн бұрын
awesome job
@downtheshedwithbyron7 күн бұрын
Thanks mate 👍
@laurenceeslava61359 күн бұрын
Can you use 0w 20 for Xtrail 2008
@downtheshedwithbyron9 күн бұрын
Nar sure mate depends on your engine condition and where your located i use the Penrite app to work out what i need to run
@rayray416813 күн бұрын
thank you
@downtheshedwithbyron13 күн бұрын
No dramas mate 👍
@purdydell451314 күн бұрын
Just curious to know why would you run a thermo that opens in the 70s to then the new one to open in the 80s which causes you car to run hotter.I would switch back to the 70 degree thermo as it opens a lot sooner and keeps your car cooler.
@downtheshedwithbyron13 күн бұрын
Good question man I did the change years ago and from memory it ran the engine at about 82ish once fulling open it flowed better dropping the temps down to 78 ish This summer I played around with the TD42 turbo thermostat which sits around 78
@pingpong965615 күн бұрын
I always thought if you pump the brake with bleeder open, that air could get sucked back in from bleed screw leaking - is this not the case?
@downtheshedwithbyron14 күн бұрын
It can but if you pull 1 of those bleed bottles apart youll see the hose is at the bottom and with a small amount of fuild in it air wont suck back up cool idea hey
@pingpong965615 күн бұрын
Do you have a video of jacking a CX7 onto four jack stands - that would make swapping tires really easy... I looked underneath but I could not identify good lifting points to get four jack stands setup. Also got to replace the prop shaft soon, then it would really help!
@downtheshedwithbyron14 күн бұрын
That would make a great video dude if you get stuck could probably work it out from the front and rear brake videos As i mentioned in the shed update video last ive sold the CX7 and now we have a C200
@SwiftRIBSAust15 күн бұрын
Good vid mate
@downtheshedwithbyron15 күн бұрын
Cheers mate 👍
@joseorozco865417 күн бұрын
Amazing video! Very well explained, thanks!
@downtheshedwithbyron16 күн бұрын
No dramas mate 👍
@hedlesshossman18 күн бұрын
Champion. Thanks mate!!
@downtheshedwithbyron18 күн бұрын
No dramas mate 👍
@TheRenoir18 күн бұрын
Thanks for a great explanation. My mechanic wanted to replace the whole shaft and buy it interstate with all the added costs and labour etc! About $100 for the 3 pce kit on eBay for an old car I love that won't have heaps of k's done on her anymore anyway. I'll be more than a grand up afterwards. Cheers.
@downtheshedwithbyron17 күн бұрын
Yeah sweet mate 👌 👍
@sergeyfirs153419 күн бұрын
Отлично!👍
@downtheshedwithbyron18 күн бұрын
Cheers
@shanelocke23719 күн бұрын
ONYA CHAMP THAT HELPED OUT BIG TIME.MY IDLER PULLY SHEARED OFF AND THAT HELPED ME RIGHT OUT ✅️
@downtheshedwithbyron19 күн бұрын
Oh man thats awesome 👌
@jeffhampton551119 күн бұрын
Absolute legend
@downtheshedwithbyron19 күн бұрын
Cheers mate 👍
@fotogralex20 күн бұрын
Do I need to drain all the oil when I remove the gasket?
@downtheshedwithbyron20 күн бұрын
Nar can do it with out draining it mate
@EbonyHyne20 күн бұрын
This video is so easy to follow and makes me so confident I can do it myself.
@downtheshedwithbyron20 күн бұрын
Im glad i could help
@stephentoner263621 күн бұрын
Great video. But what if both are showing as closed circuit?
@downtheshedwithbyron20 күн бұрын
Could be both have failed For a ebay special $20 something could give it a go
@victorhoisington560321 күн бұрын
Well made video. Clear and concise explanation and visuals. Thanks.
@downtheshedwithbyron20 күн бұрын
No dramas mate
@MrTrentbrowne22 күн бұрын
Thanks mate, where did you buy the clock spring part from?
@downtheshedwithbyron20 күн бұрын
No dramas mate I good it from nissan
@MrTrentbrowne20 күн бұрын
@@downtheshedwithbyron thanks buddy, you remember how pricey they are?
@downtheshedwithbyron20 күн бұрын
@@MrTrentbrowne $200 ish
@MrTrentbrowne20 күн бұрын
@downtheshedwithbyron thanks mate. Great tutorial
@dhghT22 күн бұрын
Hey thanks for the video, I found it very helpful. I have got to the stage of refilling with water and draining again to clear out the flush cleaner but I can only get about 6 or 7 litres back in each time before it overflows. My manual says it should take 12 litres. I am guessing the block still has about 5 litres in it. Will that be ok?
@downtheshedwithbyron17 күн бұрын
Cheers dude 👍 Yeah id buy 10l of coolant and you'll be right
@user-rd6xd1yu5v23 күн бұрын
I HV an opel Calais 2.6 with an line 6 motor..I HV a problem with the dash and headlights not having any lights when I switch it on..and the fuelpump also not working..I HV checked all the fuses and relays and all of them are good..but I do notice the security red light is blinking when ever I pwr zo the car..is it because of this that the car won't work?..appreciate ur responds in this...I love ur vids..gives me cool knowledge about this car
@downtheshedwithbyron23 күн бұрын
Gday mate Wow youve got some dramas Cars not starting? No lights? Maybe start at the battery and go from there
@mitcho86523 күн бұрын
Thanks for making the video mate, massively helpful!
@downtheshedwithbyron23 күн бұрын
No dramas mate
@Jeremy.huntnzld23 күн бұрын
Love ya content mate , black and white basics that the average dude can follow , I know this is old vid but keep up the good work from here in NZ 👌👍
@downtheshedwithbyron23 күн бұрын
Thanks heaps mate 👍 When i get the time ill be back in to the patrols soon Take it easy Bro Byzaaa
@nikolaynikolov970824 күн бұрын
Gongratulations father you and your amazing children!Thanks for the video!I am a Patrol Fan!
@downtheshedwithbyron24 күн бұрын
Thanks heaps We really need it get back into that project
@PeterAndersons25 күн бұрын
Mate, I thought I had a bit on... you're one busy fella!! Really interesting and great update, cheers.
@downtheshedwithbyron25 күн бұрын
Thanks Pete 3 of those cars are gone the pt is destroyed and awaiting the scrap yard
@Asapsadboi26 күн бұрын
This video taught me that i poured my coolant into the overflow very nice
@downtheshedwithbyron26 күн бұрын
Nice 👌
@kingcos1927 күн бұрын
Found ya from HR! 🎉🎉🎉
@downtheshedwithbyron27 күн бұрын
Gday mate hows things going
@user-oe7qd1ip5z28 күн бұрын
Excellent. Thank you.
@downtheshedwithbyron28 күн бұрын
No dramas mate
@ciaransvloggs961928 күн бұрын
What was marked on tailshaft when pulling it apart i need to replace my centre bearing on my vs ?
@downtheshedwithbyron28 күн бұрын
Gday mate how you going The mark was to line up the splines again
@kanjozoku3728 күн бұрын
What year is your gq
@downtheshedwithbyron28 күн бұрын
Gday mate 1990
@mamcuong29 күн бұрын
Hi mate, just want to make sure if I understand it right. So leave the park brake off, if cant take off the rotor then use the screw driver to turn the gear to take off the rotor, after put the new one on, then use the screw driver to turn the gear back on until the wheel cant spin anymore, Am I correct?
@downtheshedwithbyron28 күн бұрын
How you going Yeah mate thats right 👍
@mamcuong26 күн бұрын
@@downtheshedwithbyron cheers mate, Im about to change the bearing as well but really worry cant take off the old one, do u have any other tips in that case? thanks
@shaneh934529 күн бұрын
Good variety of cars in your yard mate 😁. I would possibly be interested in the hj ute if you were getting rid of it?
@downtheshedwithbyron28 күн бұрын
Cheers mate 👍 Yeah thinking of pulling the drive line out and selling the shell
@shaneh934528 күн бұрын
@downtheshedwithbyron no problems mate. Im keen for it as a roller 🙂
@klr34629 күн бұрын
Grouse channel mate subscribed
@downtheshedwithbyron29 күн бұрын
Cheers mate 👍
@dejandejan473Ай бұрын
how many km did that car travel? was there too much noise in the cabin due to faulty wheel bearings?my cx 7' has 170 tkm and it's noisy at the rear end, for now I can't locate which bearing the noise is coming from.
@downtheshedwithbyron29 күн бұрын
When i changed them it would of be about 260km
@liamwhytcross1034Ай бұрын
Hey mate I'm currently trying to swap in a new fuel feed hose on a wh v8 statesman. Is the only way to do that to remove the tank
@downtheshedwithbyronАй бұрын
Hey dude yeah will have to drop it down
@liamwhytcross1034Ай бұрын
@@downtheshedwithbyron cheers mate I've dropped it down got alot of fuel in it is there a drain plug on these fuel tanks and if not how do I drain the tank thanks for the help!
@downtheshedwithbyronАй бұрын
@@liamwhytcross1034 no drain plugs unfortunately
@liamwhytcross1034Ай бұрын
@@downtheshedwithbyron damn what's the best method to drain it
@downtheshedwithbyronАй бұрын
@@liamwhytcross1034 if you can pump it out or tip it out the filler is what ive had to do before
@stevenbullock9274Ай бұрын
Calais looks better as the p plater style
@downtheshedwithbyronАй бұрын
Haha yeah boy 😎
@davidboi2352Ай бұрын
You have got a huge thumbs up and subscription. Thanks mate.
@downtheshedwithbyronАй бұрын
Cheers bro 👌
@Shanes_ShedАй бұрын
Must have got some special air into that rear tyre at maxx pinjarra 😋 And I'm defiantly a fan of the defect spec calais
@downtheshedwithbyronАй бұрын
Haha 😄
@Shanes_ShedАй бұрын
@@downtheshedwithbyron The in laws barina may have crapped out (I gotta head down south during the school holidays to check it out) so I might have a vehicle suitable for a derby or auto karnage 1000. It may have lost oil pressure or the sensor is faulty but it got massively overfilled with oil and shes sounding a bit rattly now apparently
@1969RiskyАй бұрын
Yep life gets in the way on things you want to do! Lol at this rate you'll be starting a dodgy car yard! I'd go with more content on the Calais. Drop the suspension all round to 2 finger height on the wheel arches. Holden content never goes astray. The spare engines I'd say do them up, get them running & sell them to fund other projects. You can get the big fella to give you a hand. Holden engines are easy to build. The VY wagon, swap the V6 for one that's good. The old block, turn it into a coffee table. The Nissans, well rust is part of them. Do some vids on how to tackle the rust (once you get your welder) & the same with the Landcruiser. The cruisers weak point is rust around the screen so you might need a screen repairer to take out the front screen & get stuck into it. Good to see you back mate, can't wait for the next video.
@downtheshedwithbyronАй бұрын
Thanks mate Yeah the calais would look mint at that height Rust repairs is not my thing happy to have a crack though The cruiser ill leave till robbie works out what he whats to do Was talking to the Big fella is we sell the 6s we could fund a v8 Anyway take it easy mate 👍
@1969RiskyАй бұрын
@@downtheshedwithbyron With the rust repairs around the turret, cut the metal a bit bigger than the rust area itself & then weld the metal on & then smooth it off. Smaller bit's I'd use gorilla hair.
@downtheshedwithbyronАй бұрын
@@1969Risky oh sweet mate 👌 sold that lancer and 300zx today
@adamstab1Ай бұрын
I don't want hitman just gangster 😂
@downtheshedwithbyronАй бұрын
Yeah boy 😎
@darrenmoore2Ай бұрын
good to see your rehydrating with cordial mate. dude, finish the debuild project.
@downtheshedwithbyronАй бұрын
I know we need to get into it
@shanesmith9356Ай бұрын
Vr Calais looks best with 18 inch wheels. Much better traction for cornering safely. I have genuine HSV VT GTS wheels with new shadow chrome paint on my Vt Clubsport 5l. Would prefer a 5l for your calais but if you do the ls1 from the vt calais you are getting it will still be sweet.
@downtheshedwithbyronАй бұрын
That Clubsport would look tuff with those wheel The ls is best bang for buck for me should be a good thing but still planning it
@shanesmith9356Ай бұрын
@downtheshedwithbyron Yes I love the look of the VT GTS wheels. Very expensive but worth it to get a set in perfect condition. Good luck with your VR Calais. Hope to see it in person around Perth eastern suburbs.
@jamescooke3058Ай бұрын
Stock wheels for the vr
@downtheshedwithbyronАй бұрын
Yep i love both haha
@Oz_RebuildsАй бұрын
what do you think im doing with the VT mate? lol reliving my younger days
@downtheshedwithbyronАй бұрын
Haha gold 🤣
@Oz_RebuildsАй бұрын
hahaha i live in barker and those wheels look amazing
@downtheshedwithbyronАй бұрын
I use to take my girls up to Hahndorf for a nice drive through the hills haha
@downtheshedwithbyronАй бұрын
I also use to go up the mt barker for work fixing the rubbish trucks
Пікірлер
Need ur help I have a vz 05 5.7liter 6speed sedan car ran then stops so chanced fule fitter it runs an lease than 2 or 5 seconds stops running wood my fule pump have shit it self
Gday mate Now im guessing youve got fuel that the filter is on the right way and can you hear the pump prime before you try and start it?
@downtheshedwithbyron yes it primes runs then lease the 5 seconds later shuts down
Cheers mate just did this on a Volvo S40 and the low end power is back once again.
Awesome mate
Thanks a lot real help
No dramas mate 👍
Cheers mate love the video it was awesome, now after watching your video im all set to do mine and now im getting the run about on which is rhe correct service kit, repco has 3 kits stating they fit my vehicle, but i dont think any of them do, im only planning on using a repco or ryco kit ( quality kit) do you still have the part number for your kit you used? Thanks mate keep up the good work
Thanks mate 👍 Sorry i did this job i think 4 years ago it would of been a ryco kit
About to do this with my 2001 wh grange 🎉
Sweet dude 👌
awesome job
Thanks mate 👍
Can you use 0w 20 for Xtrail 2008
Nar sure mate depends on your engine condition and where your located i use the Penrite app to work out what i need to run
thank you
No dramas mate 👍
Just curious to know why would you run a thermo that opens in the 70s to then the new one to open in the 80s which causes you car to run hotter.I would switch back to the 70 degree thermo as it opens a lot sooner and keeps your car cooler.
Good question man I did the change years ago and from memory it ran the engine at about 82ish once fulling open it flowed better dropping the temps down to 78 ish This summer I played around with the TD42 turbo thermostat which sits around 78
I always thought if you pump the brake with bleeder open, that air could get sucked back in from bleed screw leaking - is this not the case?
It can but if you pull 1 of those bleed bottles apart youll see the hose is at the bottom and with a small amount of fuild in it air wont suck back up cool idea hey
Do you have a video of jacking a CX7 onto four jack stands - that would make swapping tires really easy... I looked underneath but I could not identify good lifting points to get four jack stands setup. Also got to replace the prop shaft soon, then it would really help!
That would make a great video dude if you get stuck could probably work it out from the front and rear brake videos As i mentioned in the shed update video last ive sold the CX7 and now we have a C200
Good vid mate
Cheers mate 👍
Amazing video! Very well explained, thanks!
No dramas mate 👍
Champion. Thanks mate!!
No dramas mate 👍
Thanks for a great explanation. My mechanic wanted to replace the whole shaft and buy it interstate with all the added costs and labour etc! About $100 for the 3 pce kit on eBay for an old car I love that won't have heaps of k's done on her anymore anyway. I'll be more than a grand up afterwards. Cheers.
Yeah sweet mate 👌 👍
Отлично!👍
Cheers
ONYA CHAMP THAT HELPED OUT BIG TIME.MY IDLER PULLY SHEARED OFF AND THAT HELPED ME RIGHT OUT ✅️
Oh man thats awesome 👌
Absolute legend
Cheers mate 👍
Do I need to drain all the oil when I remove the gasket?
Nar can do it with out draining it mate
This video is so easy to follow and makes me so confident I can do it myself.
Im glad i could help
Great video. But what if both are showing as closed circuit?
Could be both have failed For a ebay special $20 something could give it a go
Well made video. Clear and concise explanation and visuals. Thanks.
No dramas mate
Thanks mate, where did you buy the clock spring part from?
No dramas mate I good it from nissan
@@downtheshedwithbyron thanks buddy, you remember how pricey they are?
@@MrTrentbrowne $200 ish
@downtheshedwithbyron thanks mate. Great tutorial
Hey thanks for the video, I found it very helpful. I have got to the stage of refilling with water and draining again to clear out the flush cleaner but I can only get about 6 or 7 litres back in each time before it overflows. My manual says it should take 12 litres. I am guessing the block still has about 5 litres in it. Will that be ok?
Cheers dude 👍 Yeah id buy 10l of coolant and you'll be right
I HV an opel Calais 2.6 with an line 6 motor..I HV a problem with the dash and headlights not having any lights when I switch it on..and the fuelpump also not working..I HV checked all the fuses and relays and all of them are good..but I do notice the security red light is blinking when ever I pwr zo the car..is it because of this that the car won't work?..appreciate ur responds in this...I love ur vids..gives me cool knowledge about this car
Gday mate Wow youve got some dramas Cars not starting? No lights? Maybe start at the battery and go from there
Thanks for making the video mate, massively helpful!
No dramas mate
Love ya content mate , black and white basics that the average dude can follow , I know this is old vid but keep up the good work from here in NZ 👌👍
Thanks heaps mate 👍 When i get the time ill be back in to the patrols soon Take it easy Bro Byzaaa
Gongratulations father you and your amazing children!Thanks for the video!I am a Patrol Fan!
Thanks heaps We really need it get back into that project
Mate, I thought I had a bit on... you're one busy fella!! Really interesting and great update, cheers.
Thanks Pete 3 of those cars are gone the pt is destroyed and awaiting the scrap yard
This video taught me that i poured my coolant into the overflow very nice
Nice 👌
Found ya from HR! 🎉🎉🎉
Gday mate hows things going
Excellent. Thank you.
No dramas mate
What was marked on tailshaft when pulling it apart i need to replace my centre bearing on my vs ?
Gday mate how you going The mark was to line up the splines again
What year is your gq
Gday mate 1990
Hi mate, just want to make sure if I understand it right. So leave the park brake off, if cant take off the rotor then use the screw driver to turn the gear to take off the rotor, after put the new one on, then use the screw driver to turn the gear back on until the wheel cant spin anymore, Am I correct?
How you going Yeah mate thats right 👍
@@downtheshedwithbyron cheers mate, Im about to change the bearing as well but really worry cant take off the old one, do u have any other tips in that case? thanks
Good variety of cars in your yard mate 😁. I would possibly be interested in the hj ute if you were getting rid of it?
Cheers mate 👍 Yeah thinking of pulling the drive line out and selling the shell
@downtheshedwithbyron no problems mate. Im keen for it as a roller 🙂
Grouse channel mate subscribed
Cheers mate 👍
how many km did that car travel? was there too much noise in the cabin due to faulty wheel bearings?my cx 7' has 170 tkm and it's noisy at the rear end, for now I can't locate which bearing the noise is coming from.
When i changed them it would of be about 260km
Hey mate I'm currently trying to swap in a new fuel feed hose on a wh v8 statesman. Is the only way to do that to remove the tank
Hey dude yeah will have to drop it down
@@downtheshedwithbyron cheers mate I've dropped it down got alot of fuel in it is there a drain plug on these fuel tanks and if not how do I drain the tank thanks for the help!
@@liamwhytcross1034 no drain plugs unfortunately
@@downtheshedwithbyron damn what's the best method to drain it
@@liamwhytcross1034 if you can pump it out or tip it out the filler is what ive had to do before
Calais looks better as the p plater style
Haha yeah boy 😎
You have got a huge thumbs up and subscription. Thanks mate.
Cheers bro 👌
Must have got some special air into that rear tyre at maxx pinjarra 😋 And I'm defiantly a fan of the defect spec calais
Haha 😄
@@downtheshedwithbyron The in laws barina may have crapped out (I gotta head down south during the school holidays to check it out) so I might have a vehicle suitable for a derby or auto karnage 1000. It may have lost oil pressure or the sensor is faulty but it got massively overfilled with oil and shes sounding a bit rattly now apparently
Yep life gets in the way on things you want to do! Lol at this rate you'll be starting a dodgy car yard! I'd go with more content on the Calais. Drop the suspension all round to 2 finger height on the wheel arches. Holden content never goes astray. The spare engines I'd say do them up, get them running & sell them to fund other projects. You can get the big fella to give you a hand. Holden engines are easy to build. The VY wagon, swap the V6 for one that's good. The old block, turn it into a coffee table. The Nissans, well rust is part of them. Do some vids on how to tackle the rust (once you get your welder) & the same with the Landcruiser. The cruisers weak point is rust around the screen so you might need a screen repairer to take out the front screen & get stuck into it. Good to see you back mate, can't wait for the next video.
Thanks mate Yeah the calais would look mint at that height Rust repairs is not my thing happy to have a crack though The cruiser ill leave till robbie works out what he whats to do Was talking to the Big fella is we sell the 6s we could fund a v8 Anyway take it easy mate 👍
@@downtheshedwithbyron With the rust repairs around the turret, cut the metal a bit bigger than the rust area itself & then weld the metal on & then smooth it off. Smaller bit's I'd use gorilla hair.
@@1969Risky oh sweet mate 👌 sold that lancer and 300zx today
I don't want hitman just gangster 😂
Yeah boy 😎
good to see your rehydrating with cordial mate. dude, finish the debuild project.
I know we need to get into it
Vr Calais looks best with 18 inch wheels. Much better traction for cornering safely. I have genuine HSV VT GTS wheels with new shadow chrome paint on my Vt Clubsport 5l. Would prefer a 5l for your calais but if you do the ls1 from the vt calais you are getting it will still be sweet.
That Clubsport would look tuff with those wheel The ls is best bang for buck for me should be a good thing but still planning it
@downtheshedwithbyron Yes I love the look of the VT GTS wheels. Very expensive but worth it to get a set in perfect condition. Good luck with your VR Calais. Hope to see it in person around Perth eastern suburbs.
Stock wheels for the vr
Yep i love both haha
what do you think im doing with the VT mate? lol reliving my younger days
Haha gold 🤣
hahaha i live in barker and those wheels look amazing
I use to take my girls up to Hahndorf for a nice drive through the hills haha
I also use to go up the mt barker for work fixing the rubbish trucks