Пікірлер

• 
  @kmlumd4417 күн бұрын

  This vid is useful for ppl installing crossbars who dont have rails too. I did the job without breaking anything thanks to you. I thought u were crazy for drilling right above ur car paint but i had to dremel there as well so i get it.

• 
  @joealimond1685Ай бұрын

  Can you please put the link to the racks??

• 
  @xonkkramАй бұрын

  www.amazon.com/dp/B082MNZGYL?ref=ppx_pop_mob_ap_share

• 
  @jonathanbarnes4597Ай бұрын

  I wish you hadn't skipped the part of removing the brackets. I need a step by step 😭

• 
  @xonkkramАй бұрын

  Which brackets?

• 
  @jeffcantwell8764Ай бұрын

  My mechanic quoted $600-800 to replace plugs. After watching this, I'm thinking maybe I give it to them.

• 
  @vitriolix3 ай бұрын

  thanks for the video, not a ton of tutorials out there

• 
  @jeanneoregan52443 ай бұрын

  What is the distance of your cross bars mine came to 41 inches and I cannot attach my Thule cargo, Can you attach it to the bolt enclosed in the yellow clips?

• 
  @xonkkram3 ай бұрын

  I think I saw a post about somebody doing that. I suppose it's possible.

• 
  @jakevenable80574 ай бұрын

  Thanks for the video, it was helpful when I put mine on today. Did you put the wind deflector on? They go onto the end cap piece. I had whistling (even after installing thicker side facing forward). It took 10 mins to slide those on and took away the whistling. The instructions didn’t include the deflector step, but the video on Amazon did. Hope this helps someone else too.

• 
  @xonkkram4 ай бұрын

  Yes I did. That's the easy part😉

• 
  @theyallsuckash17 ай бұрын

  What side is number 3 cylinder on?

• 
  @markmaresca406611 ай бұрын

  Thanks, great video. I just completed this job on my 2001 Pathfinder. I found that you do NOT need to mess with the throttle body to get that middle plug out. The idle air controller right beneath the throttle body comes off easily with 2 screws, and that frees up the path to the tricky middle plug. Plus, while it's off you can inspect and clean it up for better idling. That was my experience anyway ✌️

• 
  @nathanbane946411 ай бұрын

  Get at it little man! Good job

• 
  @meganbrady7286 Жыл бұрын

  Very courageous young man! Song beautifully 👏🏼 Well done Dylan 🫶🏼

• 
  @radamespenaburgos5783 Жыл бұрын

  Por que mi nissan pathfainer hace como si fuera un golpe en los link atrás

• 
  @ahmadfawadjanbaz4369 Жыл бұрын

  How to solve the coil misfire

• 
  @ricardobaica3230 Жыл бұрын

  Código p 1135

• 
  @thereserivard2298 Жыл бұрын

  Great job and a great voice! Dylan: 🎉

• 
  @paulaheien137 Жыл бұрын

  One of my favorite Christmas songs

• 
  @michellesigler3714 Жыл бұрын

  😊thank you so much. Your video helped so much.😊

• 
  @graceisatakoroma4222 Жыл бұрын

  What is the solution for no current on coil 6

• 
  @xonkkram Жыл бұрын

  I am not sure what you mean. No spark on coil 6?

• 
  @ronlind17572 жыл бұрын

  Great video! Did you replace throttle body gasket?? I have misfire code on #3, your opinion.. should I just replace all 6 plugs first to see if that fixes it?? Will be doing this to my '02 this week. Thanks

• 
  @xonkkram2 жыл бұрын

  I would replace the plugs if they haven't been replaced in over 50k miles. You could also swap #3 coil with another one and see if the code moves to that cylinder. That way you know for sure that the coil is bad. If I remember correctly I think the throttle body gasket is reusable.

• 
  @ronlind17572 жыл бұрын

  @@xonkkram Thanks so much!

• 
  @meharabdulshakur72872 жыл бұрын

  Hi I checked my all coils and plugs its working but still misfiring help

• 
  @xonkkram2 жыл бұрын

  If you are sure that is not ignition, that leaves only fuel or mechanical issues. Try swapping parts between cylinders and see it the misfire moves to another cylinder.

• 
  @igadget562 жыл бұрын

  Why would you waste so much time

• 
  @xonkkram2 жыл бұрын

  Just so you would waste your time watching it.

• 
  @tonyrome0682 жыл бұрын

  Great vid but you should speak up, very hard to hear!

• 
  @lnkee2 жыл бұрын

  Hi ... is it possible to show how to replace a 2001 Nissan Pathfinder intake valve tube. I think that is what it is called. Connected to the throttle. Thx if possible.

• 
  @lnkee2 жыл бұрын

  Don't worry about it. I see that you're doing it at the middle of the video. Thanks!

• 
  @tozq3 жыл бұрын

  Good info but all I've seen is your back :D. Should put your camera another side or on the top.

• 
  @xonkkram3 жыл бұрын

  That's my good side. My priority was getting the job done in a timely fashion. Just figured I'd make a simple video to help others since I couldn't find one.

• 
  @DavidHernandez-ue4fz2 жыл бұрын

  @@xonkkram how long did you take to done this job,thanks.

• 
  @xonkkram2 жыл бұрын

  @@DavidHernandez-ue4fz this was a while ago but maybe an hour or an hour and a half?

• 
  @DavidHernandez-ue4fz2 жыл бұрын

  @@xonkkram I have an 02 infiniti QX4,I guess should be the same engine,right?

• 
  @WCGwkf3 жыл бұрын

  I'm in the middle of replacing the intake manifold gaskets, hoses underneath, and valve cover gaskets. Gives 100% access to it all that left side is really blocked up. It really isn't a lot of work to remove it just stay organized. Pretty much gauranteed the valve cover to cover hose is broken giving you a vacuum leak if it has never been changed. Dealer said they stock them well since it's so common.

• 
  @spiffinify3 жыл бұрын

  only thing is I wish you showed us a little closer how that air manifold came out and back in, but other than that this has been a tremendous help. I've gotta change all the spark plugs on my 2003 Nissan pathfinder and a #5 coil as well so this is exactly what I needed to know

• 
  @xonkkram3 жыл бұрын

  I didn't take off the manifold, just the throttle body.

• 
  @ctg85633 жыл бұрын

  I found a fish finder device how do I test to see if it powers on at home?

• 
  @xonkkram3 жыл бұрын

  You should be able to power it with 12 volts DC

• 
  @mikemccants87193 жыл бұрын

  Thanks man changed the plugs on my sons ‘02 Pathfinder. #5 was throwing a cylinder misfire code. Plugs were shot to hell.

• 
  @floydmcmullen98333 жыл бұрын

  Thank you for this video. Looking in the engine compartment of this vehicle I just got it looked impossible.

• 
  @thorlin38263 жыл бұрын

  You helped by letting me know what I'm in for.

• 
  @joemason89703 жыл бұрын

  Same here brother.

• 
  @humbertoaguirre32293 жыл бұрын

  Help where are the spark plugs located in the engine? Tia

• 
  @xonkkram3 жыл бұрын

  Under the coil packs which are under the fuel rails.

• 
  @humbertoaguirre32293 жыл бұрын

  @@xonkkram thanks man

• 
  @stanleykeith69694 жыл бұрын

  Add you water first, then it gets mixed better.

• 
  @MRSIN1874 жыл бұрын

  Does anyone else have play in the drum? Mine moves back and forth about 4 inches when the handle is locked.

• 
  @VincenzoLuzzo4 жыл бұрын

  Does anyone know the part number for cylinder #1 coil replacement?

• 
  @xonkkram4 жыл бұрын

  Before 8/00-224484W000. After 8/00-224484W001

• 
  @VincenzoLuzzo4 жыл бұрын

  what sensitivity setting did you have the dial at on the spark tester

• 
  @xonkkram4 жыл бұрын

  You have to adjust it based on what the other coils putting out.

• 
  @tonystowe16104 жыл бұрын

  Thanks for the video. I replaced all (6) ignition coils and spark plugs, and engine runs great. but my fuel economy went from 18 mfg to 15 mpg. Is there any fuel/air mix adjustments to be made?? I did have to remove the housing for the idle air mixture to get at my #4 coil. Is there any adjustment to be made there??? Thanks again for your video.

• 
  @xonkkram4 жыл бұрын

  All adjustments are electronically controlled and cannot be adjusted. However, if there is an air leak from that area, that could cause poor fuel economy.

• 
  @manuelgarcia1514 жыл бұрын

  I wanted to see it step by step, I wish you wouldn’t have skipped the prep work.

• 
  @TheCornstalker4 жыл бұрын

  I been chasing a rev problem it jumps from 1400 to 2000 and back once its warmed up you can get past it but thats weear i need to be when driving in town any ideas im just abought to pull plugs and replace but dought its the problem thanks good vido buddy a lot of guys wont take on a task so if they see it gives incentive

• 
  @raymondtorres26754 жыл бұрын

  At least I know what side the spark plugs are on.

• 
  @raymondtorres26754 жыл бұрын

  Didn't find it helpful because all we see is your back.

• 
  @mahfoozmahfooz23175 жыл бұрын

  My car pnthfnder 2004 Plugs no working

• 
  @SapphireKashmir5 жыл бұрын

  Where can I find the condensed ignition coil, please and thank you?

• 
  @xonkkram5 жыл бұрын

  What store or where on the vehicle? Not sure what you're asking for.

• 
  @drychalice5 жыл бұрын

  What did he say ?

• 
  @garygerard42905 жыл бұрын

  I just finished putting a motor on an old, free mixer I got from a Craig's List ad - Much nicer than a hoe and wheelbarrow, 'Much

• 
  @you-tubejunkie29265 жыл бұрын

  What did he say ?......👎

• 
  @mcadam28045 жыл бұрын

  Thanks for the helpful video...as already mentioned a few of the angles weren't the best but overall a very helpful video...I am changing two of my coils myself soon! cheers.

• 
  @kcender37715 жыл бұрын

  I'm not trying to shade anyone involved in this video or the people commenting, but I have professionally dealt with pouring cc for some thirty years and have even used these HF mixers before. Here's a tip: first, be realistic about how much cc you can place (mix) with them; they are small and what you just mixed will start to set immediately creating a problem with the next batch. Moisten the ground you are placing the cc on before you start so the moisture won't be sucked out of the batch you just mixed before the next drop. Be Realistic, you are only talking about a square foot of coverage with the load. Knit the two loads together at their "join" with a shovel and keep it small with a 2x4 mid-form so you are not trying to do too much. Also, don't spray water into the barrel before putting in the dry product, it will only cause clumping and create a bad mix. If you know someone with a 3/4 ton truck, have them pick up a mixer trailer (one yard) of cc and bring it to your project. This should produce 81 sq. feet of pad measured at 3 1/2". This is the only way you will get a decent result on a small project. Don't step over a dollar to pick up a dime.

• 
  @garykent81935 жыл бұрын

  When you tested the coil with tick tracer did put it right on the coil block or the connector, I assume the coil block?

• 
  @xonkkram5 жыл бұрын

  Yes, on the coil block. But usually if you just get close, that is good enough.

• 
  @doug45015 жыл бұрын

  Tide needs to merge with quickrete, then we would have dust free quick pods.

• 
  @jrx26626 жыл бұрын

  next time use a mask

• 
  @xonkkram6 жыл бұрын

  JRX 2 how do you know I wasn't?

• 
  @jrx26626 жыл бұрын

  your voice sound clear, but that's just me looking out for people, cause that dust could hurt your lungs!

• 
  @sealedinchrist54133 жыл бұрын

  You dont need to worry about Covid when your mixing concrete. lol jk

• 
  @gsr2envy6 жыл бұрын

  where did you get that tester? i wanna get one. good video. i have to replace my cylinder #1. helps me out. good people like you will be rewarded. thumbs up to you

• 
  @xonkkram6 жыл бұрын

  gsr2envy www.amazon.com/dp/B000JFHMPC/ref=cm_sw_r_cp_awdb_t1_Rd8sBbFAC8KST thanks for the props

• 
  @VincenzoLuzzo4 жыл бұрын

  Does anyone know the cylinder #1 part number and information? I have to replace mine and can’t find the information for the part