Пікірлер

• 
  @jod-service4448 күн бұрын

  👍👍👍

• 
  @thomask4836Ай бұрын

  Thanks for posting this! I used to work in a machine shop but never saw how rotors were machined. Just did a brake job where the rotors were machined and now I understand why one of them was returned to me with .010" runout!

• 
  @joseloredo25172 ай бұрын

  Gracias hermano estoy seguro que si salistes un poco pedo gracias por compartir todo chingon y chido

• 
  @user-rr7je8iw3b2 ай бұрын

  This machine is way better than the Coats 1250. The Hunter GSP9700 is easier to operate and learn.

• 
  @ronnierykers36382 ай бұрын

  Nice machine but Duquesne made in Belgium is for me the best

• 
  @ericboisselle11452 ай бұрын

  If you balance a wheel and it comes out ok, take it off the mount and try it again should it be ok? my tire guys says it impossible to remount and see if it is still ok. Thank you for time you took to explain all this

• 
  @troydreams63002 ай бұрын

  Thanks but you can Fs cut this video down by 10 min at least

• 
  @Headsup95502 ай бұрын

  Since the measurement for the outside of the wheel lip surface is essentially just a way for the machine to know the width of the wheel (the outside measurement function became available at the same point in time as we no longer had to measure the wheel width with the calipers) , is there a way to enter the width of the wheel if it happens to be stamped on the wheel somewhere?

• 
  @claudiogiovingo49033 ай бұрын

  That last and vey important step ( smooth the surface with sand paper) is what I should say should be done with the same machine, so not wearing so quickly a brand new originals oem braking pads, that for sure star an unevem surface again an so on , and you will realize that changing brand new rotors is cheaper amd ypu always have a brake sysytem with fuul power ready for any braking emergency. I appreciate this good video, and good luck

• 
  @Isaacpsalms3 ай бұрын

  What may be the issues

• 
  @Isaacpsalms3 ай бұрын

  I have question for you Our hunter balancing machine have error When you apply loadforce After spinning the time its says Too much speed And stops

• 
  @ingefrainromero51094 ай бұрын

  .... Das ist kool... danke

• 
  @larranag4 ай бұрын

  QM is helpful for faculty to improve student success.

• 
  @joseedimilsondiniz5584 ай бұрын

  Em portuense

• 
  @user-rh9mr7zz6w4 ай бұрын

  Interested can I work for you

• 
  @alfredogarcia86205 ай бұрын

  I love Hunter's equiment. One of the best equipemtn in the U.S. I've been working with them for over 20 years.

• 
  @theodorekell5 ай бұрын

  Looks like too much work for on-car. Someone with less skill or badly calibrated machine can ruin the rotor anyway. I see in the comments, people do have positive points about it. But what if the rotor was installed not on the clean surface and so on.. It is always better to take it off and clean inside. + for the customer, save some now, it can rust-in even more. Especially for mazda I would want to pull that rotor off and clean inside. They sometimes rust-in badly, to the point of need to cut that rotor to remove..

• 
  @chikeziejustice5 ай бұрын

  How can one get this training? Am very much interested to learn.

• 
  @foulematouibrahim9646 ай бұрын

  Hello I hope you are well I do tire balancing parallelism I would like to work with you one day

• 
  @jamestartaglia76866 ай бұрын

  My God it's a science now to change a tire....wow

• 
  @sudhansusekharsamal19966 ай бұрын

  sir i want to work with you.

• 
  @Bounty-Hunter697 ай бұрын

  Rubish video,,,,,,,,,,,,,,,,,,,,,,,show on 20´´ runflat with 35 profile....

• 
  @James28R7 ай бұрын

  This aint gonna work on a car with an lsd. or it will do some damage at best

• 
  @rambabusen14937 ай бұрын

  मशीन मुझे खरीदना है

• 
  @user-qp2wi9bx7e7 ай бұрын

  Assalamu alaikum bro how are you bro your work is very nice alhamdulillah very good bro i am also a technician tire mechanic like you bro my name is md arif hussain bro i am a bangladeshi citizen bro can you give me a job i have eight years of experience i am 20 years old

• 
  @alberfernandorojas12298 ай бұрын

  Please how much the cost?

• 
  @dodgert8 ай бұрын

  12 clock tpms or it can break. At your pace I would be out of business

• 
  @davidvdheijden39708 ай бұрын

  As a mechanic I say its way to complex to balance a wheel! We have a Schenk balance machine for about 35 years never had isuses with balance a wheel! The biggest problem from this kind of machines is the horizontal axle!! In industries the always work with vertical axles this machine hunter en all of others clones the are not good build, what do you think when the roll make presure on the vertical axle more difference you have and thats wat you don’t want when you balancing!

• 
  @dilipmakwana41248 ай бұрын

  Job for me I am wheel alignment and wheel balancing technician

• 
  @dilipmakwana41248 ай бұрын

  Job for me

• 
  @nikkasingh87938 ай бұрын

  Price kya hai

• 
  @moitan4349 ай бұрын

  I just want to understand, because every I boughttire alway charge the wheel balancing

• 
  @patrickcalatayud49239 ай бұрын

  Dommage qu'il n'y a pas une traduction en français ❓

• 
  @dawsong41469 ай бұрын

  Im in automotive class and hes making us watch the video 10/10 video very helpful thanks mr gurrero

• 
  @dbildenz11209 ай бұрын

  The older machine is faster and better good luck in school

• 
  @PrinceEIijah8 ай бұрын

  same dawg

• 
  @ausomecatman463610 ай бұрын

  He forgot to sand it down

• 
  @SloppyShotz10 ай бұрын

  thanks man my 2nd week at a tire shop. I almost want to give up, but I know I can do this shit.

• 
  @nutherbutter16578 ай бұрын

  Did you give up ?

• 
  @SloppyShotz8 ай бұрын

  @@nutherbutter1657 NOPE! I’ve earned respect with my manager and my co workers. Light work baby. I make the job my bitch, but working on dually’s can humble you.

• 
  @Mountain-Man-300010 ай бұрын

  Great way to ruin a transaxle!

• 
  @LoveNoThotss10 ай бұрын

  Thanks

• 
  @fromisheon486711 ай бұрын

  There are ture shops that put the cone from the outside. Is that a method?

• 
  @fromisheon486711 ай бұрын

  I love the 4 pedal machine.

• 
  @rubiconklbrutorowman7577 Жыл бұрын

  I will reply ONCE about some comments about the old school machine that involves labor intensive is simple to operate, etc. I very much disagree with below common the older tire changing machine is better; specifically, the commentators are missing at least few points: Using the older tire change machine meaning users have more chance to get injury, take more efforts, make you tired after changing several dozen tires, and take MUCH more time using the old school tire changing machine! On the contrary, using ****FULLY automatic *Hunter's Revolution Tire Changing machine, the three points I have stated will make substantial improvements; needless to say, after viewing the Hunter's FULLY automatic tire changing machine, it is my intention to purchase the Hunter's machine when N if I have auto repair shop, possibility. I *intend to purchase Hunter's Fully automatic tire changing machine and no fuss n mass n MOST importantly NO injury risk, one has to ask for it! There will be lot less energy required also that can be used to repair other vehicles' issues! It is NOT take too long to learn know how to push some dozen buttons, one time, and Hunter's full automatic tire change machine WILL *NOT have deadly injury NOT once but **EVERY TIRE CHANGE while INCREASING productivity, and employees' satisfaction of work due to **far less efforts required to change tire after tire after tire, etc. and do NOT forget time saving meaning change to earn more revenue repairing other vehicles, which time is money in any business operation!

• 
  @rubiconklbrutorowman7577 Жыл бұрын

  Excellent step by step demonstration! The other excellent point is *review, I think one slow n one fast after first time *break down step by step demonstration! Very well done indeed!

• 
  @rubiconklbrutorowman7577 Жыл бұрын

  Just subscribed.

• 
  @angelernestosarangoarmijos9928 Жыл бұрын

  Quiero esa maquina numero

• 
  @Jersey4x4 Жыл бұрын

  why would you use a strip of 1/4oz weights and spread them out over a large area and not use a heavier weight and place it where the machine is telling you. You are causing inaccurate readings

• 
  @ugoenyinnaya3615 Жыл бұрын

  Can you teach us how to put on low profile tire

• 
  @moossful Жыл бұрын

  Waw ! That's very interesting and very helpful Thank you

• 
  @lorylangley9988 Жыл бұрын

  Great video! I have a newly acquired Ammco 4000 for my home shop. This video is a great explanation of operating the lathe!

• 
  @enabledintergers9372 Жыл бұрын

  your introduction was week !!!!!! not intended to replace a instructor????? why even see your week video!!!!?? Instead see a real one ? why invest time observing something that is not going to serve its purpose!???you talked me out of buying this model so far!! keep doing coats a favor!

• 
  @flamestar557 Жыл бұрын

  Wish it showed the measuring step because I was told we should measure drum brakes before machining to see how much we can machine off. I suppose that's a different video to look for :(