Пікірлер

• 
  @SuperThirugnanam23 сағат бұрын

  Explained well to understand.

• 
  @northwind3933 күн бұрын

  Hi boss kzread.info/dash/bejne/maGrlZaGk9zYZcY.html Но у него подключены 3 провода к батареи и она заряжается, почему?

• 
  @shivanshkhera67076 күн бұрын

  BRO DISPLAY ORIGINAL H?

• 
  @yogendrasinhpgamityogglan48447 күн бұрын

  Thanks

• 
  @danielrocha882017 күн бұрын

  Niceeeeee thanks bro

• 
  @abhijithnv345919 күн бұрын

  i have another BL-4UL battery.....is this battery ok instead of BL-5C

• 
  @PiyushPrasoon19 күн бұрын

  Its completely depends upon the availability of space, if BL-4UL battery can be fixed inside the speaker then go ahead with it, it will work. 🙂

• 
  @abhijithnv345919 күн бұрын

  @@PiyushPrasoon ys i connected bl 5c😢 ...bt not turning on no led turning on

• 
  @PiyushPrasoon19 күн бұрын

  @@abhijithnv3459 make sure you have connected the power controller small PCB circuit. check if you have detached it from the previous/old battery.

• 
  @abhijithnv345919 күн бұрын

  @@PiyushPrasoon yep i didn't disoldered that frm the beginning...then i tried without the pcb ..then also noo lights coming

• 
  @PiyushPrasoon14 күн бұрын

  @@abhijithnv3459 I would suggest not to do the direct soldering of battery from the bigger PCB. you can solder it via small power controller PCB. please watch the video from this point: kzread.info/dash/bejne/qK6MstKkoNrPedY.html In case it is still not playing sound, you have to do a basic connectivity check for all the existing connection. and check the LED status. Better connect it as I mentioned above and the try to connect it with power source and check if it is charging and check the charging indication on LED, if it will show the red indication it means it is getting charged and the connection is proper.

• 
  @DREAMER.7020 күн бұрын

  Good a vidio, am compuer is = a my computer 😁😁👍👍

• 
  @ajaykumar-xb3rp21 күн бұрын

  Battery kha se khride?

• 
  @minasingh5649Ай бұрын

  नींद होने का कारण मैं कहां अटक गई पता नहीं

• 
  @PiyushPrasoonАй бұрын

  😂😂 कोई बात नहीं, के बार फिर से देख लीजिये गा 🙂

• 
  @MrForman3Ай бұрын

  Thanks My Lighter Fell out my jacked pocked now working

• 
  @PalaniPalani-pv3uzАй бұрын

  How.is.it.repairing

• 
  @PiyushPrasoonАй бұрын

  Absolutely it's just the replacement process, as mentioned in the video title 🙂

• 
  @sijogeorge9676Ай бұрын

  but speed is very slow comparatively from jiofi network

• 
  @PiyushPrasoonАй бұрын

  Yes, the speed will be a bit slower, but speed also depends upon the distance/obstruction between the jiofi and the router. it should be within 3-5 meter radius in the line of sight.

• 
  @mehmetozbek1962Ай бұрын

  It worked! Thanks...My Dell n5010 suddenly shut down and the screen went black. When I turned on my computer using the Fn key, 7 beeps were heard. By watching your video, I determined the distance for the maximum temperature ~240 degrees with a thermometer. I heated it at this temperature for 4 minutes. As you said, liquid flux used.Finally, I applied high temperature resistant silicone (RTV) to the edges of the ATI pcb. I thought maybe it would last longer and the solders under the chip would not oxidize.

• 
  @Dhanavel_kkdiАй бұрын

  I have the speakers but the main cable was cut what is the solution for rejoint the cable with AUX

• 
  @PiyushPrasoonАй бұрын

  Just peal off the broken ends of the wires and 3.5mm Jack and do the soldering.

• 
  @letmeshowyou7007Ай бұрын

  please tell the price of dislay in local market.. its very urgent plzz

• 
  @PiyushPrasoonАй бұрын

  it price is 5500 INR

• 
  @DetoditoparatiАй бұрын

  Thank you, I saved a lot of my mother, I wanted 😂😂

• 
  @HalfTuber81Ай бұрын

  Great work 👍🏻💯

• 
  @johnsonlucky8973Ай бұрын

  Thanks❤😂

• 
  @raseesahammedАй бұрын

  where can I buy the display?

• 
  @PiyushPrasoonАй бұрын

  I have purchased this from a local vendor, you can view the number in the video.

• 
  @anilraghu86872 ай бұрын

  Yes tx. I was looking for on screen gui in Android settings.

• 
  @gshekhar522 ай бұрын

  Arey chichajaan jabardast video! Par routing wire kabhi bhi driver ke side se nahi le jana chaiye. Agar paer me latpata gaya na toh lutput jaega.😢

• 
  @PiyushPrasoon2 ай бұрын

  Waah nice observation.... Fir syad lutput gana bhi gane lege ga

• 
  @rausnarrations1662 ай бұрын

  This type is used in our compressor interface for start and stop. Is there any way stop auto after 1hr automaticall. Can we do any thing at this tactical switch.please guide me

• 
  @PiyushPrasoon2 ай бұрын

  There are several alternatives to auto stop. One of the easiest ways is to use 555 timer IC

• 
  @avinashkoli52052 ай бұрын

  Thanks bro❤

• 
  @NaturalbeautyNR3 ай бұрын

  5g se bhi connect ho jaae ga kya

• 
  @the_scorpio7773 ай бұрын

  Thanks ✌

• 
  @user-mz9hf8vn5z3 ай бұрын

  ظنسمسمسنسنسن من 😮مؤمرمرمرم

• 
  @nesheeeev3 ай бұрын

  Setup the Chromecast to Cast screen first (and not the browser) and then proceed to connect 😜

• 
  @norhiamaravilla17103 ай бұрын

  sa erya mu ne ama cgeg eyut mag towad ka haha

• 
  @norhiamaravilla17103 ай бұрын

  😂🎉😢😮😅😊

• 
  @GOOGLE-ADMlN3 ай бұрын

  OMG! Thank you for explaining this! never knew about piezo crystals.

• 
  @HAROOT-AL3 ай бұрын

  no connection for me it says no device found

• 
  @mariocomeq19613 ай бұрын

  It would be nice if you tell us the screws you are using. If I noticed good, you are using a cell phone battery to replace the original

• 
  @ananthia-00733 ай бұрын

  Thank you so much

• 
  @BoomitoMix3 ай бұрын

  Not solved 😢

• 
  @vkdem3 ай бұрын

  Very good. Thank you.

• 
  @kensowed31303 ай бұрын

  When does my motorbike stop moving, when the gauge reading point is on red or all the way down where the red end??

• 
  @PiyushPrasoon3 ай бұрын

  If the gauge enters the red boundary - it means your bike can go to reserve mode at any point of time, this is the time when rider need to move the petcock knob manually to reserve position else your motorbike will stop moving. After setting the petcock position to reserve mode, your motorbike will start consuming reserve gas from the gas tank and keep on moving until the gas tank is completely empty. At this point of time the gauge will be pointing all the way down the red end. Note: The quantity of reserve gas in the gas tank may vary depending on the motorbike brands. As per my knowledge, 2-3 liters is the minimum reserve quantity of gas in the gas tank for most motorbike brands.

• 
  @mikhail6684 ай бұрын

  Thank You So Much Brother ❤

• 
  @kodilacroix14874 ай бұрын

  I would've assumed a "tear down" meant actually taking it a part to examine the components. If all you were going to do is take the back panel off, why not just take a picture?

• 
  @reviewbypiyush16443 ай бұрын

  Oh, I just took the back panel off to show the components and accessories on the Motherboard at 3:09

• 
  @RanikaPerera4 ай бұрын

  What if there is no way to adjust the height of the table? Those knobs cannot be screwed in as there is no hole drilled into the black pieces to adjust the height

• 
  @PiyushPrasoon4 ай бұрын

  A height adjustable mechanism is given by the company in this table. This is a telescopic mechanism in which the outer pipe has a threaded hole with a knob if you want to adjust the table you just need to slide the inner pipe by moving the table up or down then you have to tighten the knob to make the table fixed in that position. If there is no way to adjust the height of the table then you have to use it the same way with default height. The table in the video with the knob is enough to tighten the table and keep it stable in the desired height so no holes are needed in the inner pipes.

• 
  @yuvrajk25384 ай бұрын

  May be different question, in bluetooth setting you already have ‘Sony RC MIC’ for me when I try to add device and press mic key with ‘vol - ‘button, i am not able to pair my remote mic to tv so that i can work with voice control. Do you have any video on that or help me here to connect remote mic to tv.

• 
  @PiyushPrasoon4 ай бұрын

  Actually that is hardcode from companies end, so in my case even the microphone pairing is getting removed it will easily get paired again. You can try adding the device and the try to follow the instructions to connect the RC Microphone

• 
  @felixyasnopolski85714 ай бұрын

  nice video tho. only one small mistake: the generated voltage is not 800 volts, you can eyeball the high voltage with simple rule: 1mm of air needs roughly 1kV to overcome the gap.

• 
  @PiyushPrasoon4 ай бұрын

  Hey @felixyasnopolski8571, thank you so much for you comment and the observation. BTW, nice observation, however if you will see the complete setup there are 2 places where spark/arc need to be generated, one which is observable - i.e. the one which you have noticed. The second spark is happening when the electron will transfer from metallic leaver to spring end point which resided under the push button. After all this I have measured the Voltage using multimeter to confirm the value and the video for the same will be available soon 🙂. BTW very nice observation and thank you once again for you valuable comment and sharing you opinion.

• 
  @felixyasnopolski85714 ай бұрын

  ​@@PiyushPrasoon you can't correctly measure high voltages with ordinary multimeter :) and there's some reasons: 1. Multimeter isn't built for measuring voltages over 1kV, divider resistors is usually either SMD or the voltage difference much higher than they can handle; 2. Even though the voltage is high, but the duration is small (hence power is small too), and for filtration there's installed RC network, and because of small time and big capacitance (for that time), the multimeter just can't correctly measure the voltage. If you really want to measure **correctly** the spark voltage, you would need an oscilloscope, and properly built high voltage probe. This is the only way of measuring high voltage spikes. Even the expensive multimeters (such as TrueRMS Fluke ones) can't measure them by design, multimeters are built to measure constant (to some extent) voltage. And nevertheless, the 1mm/kV rule still valid for eyeballing ;)

• 
  @summerchiong68944 ай бұрын

  Its possible that some smart yv doesn't have remotes and accessories option on setting? Hard to pair speaker on r smart tv. Pls help .

• 
  @PiyushPrasoon4 ай бұрын

  right, some TV may have the OLD BT chip used i.e. 4.0 or 5.0 initial technology BT chip. BLE 5.0 enabled chip is having the capability to connect with multiple devices. Can you help me with you TV Brand and its model number?

• 
  @billynomates9204 ай бұрын

  without the metal lever your finger certainly notices! 💥⚡💫👈😖😆

• 
  @PiyushPrasoon4 ай бұрын

  Hahaha nice observation, but my answer is no, I was not getting the shock as current choses the easier path to complete the circuit 😊 But 1-2 time I got the 💥😆 you might have noticed in the video the electric arc once strike my thumb 😅

• 
  @RishabNegiProject5 ай бұрын

  👍

• 
  @abogad11135 ай бұрын

  شكراااا❤❤🌹😍😍

• 
  @gregbetts80575 ай бұрын

  great vid thank you . question tho , i have a ideapad 330 -15IGM model 81D1 and no on board memory , but lenovo specks said it can only be upgraded to 8gb , could that be because there was no higher mem available at the time of manufacture ? any insite would be appreciated , thank you .

• 
  @chethankumar92805 ай бұрын

  Am unable yo get the bottom message called "bluetooth A2DP audio device connected", its paired but sound is from TV only plz help me out, and my tv is sony kdl-43W950C its support for audio ply via bluetooth TWS..

• 
  @PiyushPrasoon5 ай бұрын

  can you try some other bluetooth headphone or any other BT device just to check the connection. Note: once you device is connected - then you need to go to the bluetooth connection setting in TV to do the final connection of the device - last step which I have mentioned in the video.

• 
  @MADAN14385 ай бұрын

  thank you very much, save my million hours time

• 
  @Bismayb97775 ай бұрын

  Wips mode me ek video banaya