Scotch Lock connectors are not a good move. At best they are only temporary, or for emergency use.
@UncleRobsGarage3 күн бұрын
Excellent!
@tomtalamantez89347 күн бұрын
Is that unit the same in a 96-99 OBS Chevy
@ScottysDetailing7 күн бұрын
Yup it is and
@tomtalamantez89347 күн бұрын
@@ScottysDetailing I have a question about the operation of the hvac unit. It’s on a 99, 2 door Tahoe.
@jiangdude10 күн бұрын
Amazing videos thank you
@jjatyou2b13 күн бұрын
Title should be: Arm and face video.
@Theundisputedtruth18 күн бұрын
Is there anythinf that can be put on the bags from rocks and sharp objects by chance ? 🤔
@2403rygar22 күн бұрын
Awesome! Thank you
@MrOiram4626 күн бұрын
Do you have to remove both pins or can you leave one on while replacing one of them?
@shanew.williamsАй бұрын
Might of helped if you had told us WHICH ENGINE you're working on ? (Mine is a 2006 4.3 vortec V6, ) You didn't show struggling to get that old seal out either, lol.
@user-no3jj4ye9lАй бұрын
Which one for 65 malibu
@billiecluney3212Ай бұрын
Glad you skipped parts very not helpful
@gypsydrone8607Ай бұрын
Fantastic man! TY!!!
@freddieweimann3602Ай бұрын
I wash my bike by hand so I can find anything lose in advance....just saying 🙈
@BlondieSLАй бұрын
I know that the vid is very old now, but, 2 questions: 1) how "tight" should the tensioner on the spool itself be? I think that for someone new to MIG, it's not easy to know for sure. Too tight, and I guess there's be feeding issues. Too loose and well..... WIRE PARTY! LOL 2) what tension should be on the roller that we clamp down? I'm GUESSING that perhaps just enough to assure that the wire moves freely through the hose and not so tight as to cause drag on the motor?//
@hillcharlie2761Ай бұрын
Not being a dick but you just built a 4x4 so why not go pick up about 4 or 5 4x4s pre drill holes and just bolt them together then you can take it were you need it but the 2x4 one looks good
@reset30559Ай бұрын
You didn't show the hardest part! How do you get the nuts off the back of the screws and then how do you put them back on the new motor ? The bottom two aren't to bad but how do you get your hand in there to hold the nuts on the back ? There's no room to get your hand in there!
@BrentGossardАй бұрын
I new where you were in provo canyon.
@chachijr6396Ай бұрын
good video
@GenesisOmega666Ай бұрын
honestly though you provided the exact knowledge i needed, thank you so much
@GenesisOmega666Ай бұрын
I win!
@stevesmith582Ай бұрын
Just took mine to a body shop was told the front windshield had to be removed. Total cost was 2300.00
@user-ic4hn3qx7rАй бұрын
Great install vid! THX
@BruceSchniedermeyerАй бұрын
I can't seem to get the latch out of the door, will not fit down through the window guide & the door. Do you have a video showing that? 97 astro
@ValYukhnenkoАй бұрын
Hello! Which Loctite Blue did you use: 242 or 243? Thank you!
@leoneltrejo132 ай бұрын
Good video then the oil level should be in the side window thanks.
@d33psix882 ай бұрын
Thanks for telling us how to get it back in…
@rogerhorner74312 ай бұрын
Great video thanks!
@HolyGrounds332 ай бұрын
How did you remove the seat belt?
@markroth98272 ай бұрын
Thank you for this video. Very information.
@davet.32362 ай бұрын
Thanks! Best advice😊
@Testing3292 ай бұрын
Gloria a ti,señor,por todo/ Viva Christo Rey
@ritchiemcculloch34532 ай бұрын
Why didn''t you buy a 6 1/2 with a tweeter? Putting a 3 way down there destroyed the staging.
@LifeintheMixofthings2 ай бұрын
Thankyou for making this video!!
@brianhydrorenewal66322 ай бұрын
Thanks for doing all that work! 💯
@Joey1k2 ай бұрын
what about the gear oil????
@kodykindhart56442 ай бұрын
What if you can’t get the window up My window is stuck halfway
@Civilwarman403 ай бұрын
Great video
@Civilwarman403 ай бұрын
I dont think your son is excited as he should be to have a dad that teaches him imdependance and learning cool things
@Civilwarman403 ай бұрын
I have to comment on every video helps algothrim great job
@Civilwarman403 ай бұрын
Ive had my 2002 saturn sl1 for 4 years 3 months and i keep having to buy a tps would u happen to know why my throttle position sensor keeps going bad? Like is it possible that something else keeps making them go bad?
@Civilwarman403 ай бұрын
Man you gave me an extrodinary virw of my engine bro thank you so much for this info i love to learn and your a great teacher thanks
@Civilwarman403 ай бұрын
Thanks for your time
@Civilwarman403 ай бұрын
This vids are awesome thanks for your time
@Civilwarman403 ай бұрын
How you get that engine so shinny?
@JoseGarcia-km1vo3 ай бұрын
Excuse me, gentleman, could you give me the name of the products that you made to stir in fiberglass resin, please?
@JaceD4V1S883 ай бұрын
bought an old pressure washer from someone, found out its from 97, got it running well, but it says use sae30, can i use 5w30 since i have a quart of that laying around?
@lukeWiz442 ай бұрын
any 30 weight oil is fine. 5w30, 10w30, SAE 30.
@ggonzal69113 ай бұрын
Thank you so much. Nobody has info on the actual latch. Great detail. Really appreciate it.
@CalebBrown-fl2vt3 ай бұрын
Thanks will it be the same for a service body
@ScottysDetailing3 ай бұрын
What are you referring to when you say a “Service body”? they made this in a short bed, a long bed or stepside.
@ScottysDetailing3 ай бұрын
If you’re talking about a utility bed, the bolts and everything are the same. Sometimes the fuel ⛽️ door and the bumpers are a little bit different.
Пікірлер
Thanks homie
Scotch Lock connectors are not a good move. At best they are only temporary, or for emergency use.
Excellent!
Is that unit the same in a 96-99 OBS Chevy
Yup it is and
@@ScottysDetailing I have a question about the operation of the hvac unit. It’s on a 99, 2 door Tahoe.
Amazing videos thank you
Title should be: Arm and face video.
Is there anythinf that can be put on the bags from rocks and sharp objects by chance ? 🤔
Awesome! Thank you
Do you have to remove both pins or can you leave one on while replacing one of them?
Might of helped if you had told us WHICH ENGINE you're working on ? (Mine is a 2006 4.3 vortec V6, ) You didn't show struggling to get that old seal out either, lol.
Which one for 65 malibu
Glad you skipped parts very not helpful
Fantastic man! TY!!!
I wash my bike by hand so I can find anything lose in advance....just saying 🙈
I know that the vid is very old now, but, 2 questions: 1) how "tight" should the tensioner on the spool itself be? I think that for someone new to MIG, it's not easy to know for sure. Too tight, and I guess there's be feeding issues. Too loose and well..... WIRE PARTY! LOL 2) what tension should be on the roller that we clamp down? I'm GUESSING that perhaps just enough to assure that the wire moves freely through the hose and not so tight as to cause drag on the motor?//
Not being a dick but you just built a 4x4 so why not go pick up about 4 or 5 4x4s pre drill holes and just bolt them together then you can take it were you need it but the 2x4 one looks good
You didn't show the hardest part! How do you get the nuts off the back of the screws and then how do you put them back on the new motor ? The bottom two aren't to bad but how do you get your hand in there to hold the nuts on the back ? There's no room to get your hand in there!
I new where you were in provo canyon.
good video
honestly though you provided the exact knowledge i needed, thank you so much
I win!
Just took mine to a body shop was told the front windshield had to be removed. Total cost was 2300.00
Great install vid! THX
I can't seem to get the latch out of the door, will not fit down through the window guide & the door. Do you have a video showing that? 97 astro
Hello! Which Loctite Blue did you use: 242 or 243? Thank you!
Good video then the oil level should be in the side window thanks.
Thanks for telling us how to get it back in…
Great video thanks!
How did you remove the seat belt?
Thank you for this video. Very information.
Thanks! Best advice😊
Gloria a ti,señor,por todo/ Viva Christo Rey
Why didn''t you buy a 6 1/2 with a tweeter? Putting a 3 way down there destroyed the staging.
Thankyou for making this video!!
Thanks for doing all that work! 💯
what about the gear oil????
What if you can’t get the window up My window is stuck halfway
Great video
I dont think your son is excited as he should be to have a dad that teaches him imdependance and learning cool things
I have to comment on every video helps algothrim great job
Ive had my 2002 saturn sl1 for 4 years 3 months and i keep having to buy a tps would u happen to know why my throttle position sensor keeps going bad? Like is it possible that something else keeps making them go bad?
Man you gave me an extrodinary virw of my engine bro thank you so much for this info i love to learn and your a great teacher thanks
Thanks for your time
This vids are awesome thanks for your time
How you get that engine so shinny?
Excuse me, gentleman, could you give me the name of the products that you made to stir in fiberglass resin, please?
bought an old pressure washer from someone, found out its from 97, got it running well, but it says use sae30, can i use 5w30 since i have a quart of that laying around?
any 30 weight oil is fine. 5w30, 10w30, SAE 30.
Thank you so much. Nobody has info on the actual latch. Great detail. Really appreciate it.
Thanks will it be the same for a service body
What are you referring to when you say a “Service body”? they made this in a short bed, a long bed or stepside.
If you’re talking about a utility bed, the bolts and everything are the same. Sometimes the fuel ⛽️ door and the bumpers are a little bit different.
Worst video ever