Пікірлер

• 
  @StuartsShed2 күн бұрын

  Heck of a nice project - really well done. Cheers and all the best.

• 
  @campbellmorrison85408 күн бұрын

  Great overview thank you. I just bought a chuck and all the imperial and metric chucks on a local trading site. Its a brilliant system for sure. Mine is American I suspect because it has a 3/8 NC drawbar thread but its got no manufacturer on it so its a good thing I don't need any more collets.

• 
  @1mpishskillz11 күн бұрын

  I just want my light to come on when the power has been cut, does it matter which port i put it in on the permanent live and neutral? Think i might have a defective batch as the light just stays on and its killing off the battery, to top it off the charge indicator light doesnt light up either?

• 
  @shedmade32645 күн бұрын

  I had the same issue and it was the little jumper loop that was the key for my light. Stick to wiring the ports according to the markings on the fitting. I made sure that things were as I wanted them to be on the workbench BEFORE final mounting . They do make it tricky Shed guy

• 
  @markdavison789317 күн бұрын

  I take it this worked as intended? I'm about to make myself one.

• 
  @shedmade326416 күн бұрын

  Yep it did the trick. I can also use a 5c collet in the spindle nose to hold a piece of stock as a stop - that works pretty good shed guy

• 
  @StuartsShedАй бұрын

  Very nice. Nothing like a bit of shiny brass turning to lift the spirits. Nicely done all round. Does your lathe chuck lock? That is - can you turn the chuck in reverse?

• 
  @RustyInventions-wz6irАй бұрын

  Very nice work sir. I tried to make a ball turning attachment years ago. My experience I have to say was even less. Yours is looking great.

• 
  @machinenutdel6764Ай бұрын

  Morning Shed made, Ive just picked up a ZB32 head unit only and need to make some of the parts that are missing, I was wondering if you could let me know the measurement between the hole centres of the linkage arm that connects the middle cog to the upright bar, the mechanism that moves the head left and right ! very much appreciated...Del...

• 
  @shedmade3264Ай бұрын

  Del I have uploaded a parts diagram up in the description section. Name the part and I will measure ..... only I am about to go on holiday so it may take time The download is worth a look at least Shed guy

• 
  @StuartsShedАй бұрын

  Nicely done!

• 
  @RustyInventions-wz6irАй бұрын

  Very nice work sir. I still have to make a attachment for ball turning. I have a few ideas though. He he. Some day

• 
  @shedmade3264Ай бұрын

  cheers rusty like your channel ....... looks like you are a shed warrior fighting the same battles. I gave in on biking as I won't bounce down the road so well these days ...... good fun though Shed guy

• 
  @markrainford12192 ай бұрын

  Shoulda gone to Specsavers.

• 
  @DK-vx1zc2 ай бұрын

  nicely done ! Thanks for sharing

• 
  @StuartsShed2 ай бұрын

  Nice work - nice save. Stuff happens - as they say - but we live and learn. Nice approach clamping the old part to the new that way. 👍

• 
  @shedmade32642 ай бұрын

  cheers stuart loving your shed ... looks like home from home .... only better

• 
  @user-tb8wt8se2k2 ай бұрын

  гуд

• 
  @markrainford12192 ай бұрын

  Very.

• 
  @user-rg1pl5hj3v2 ай бұрын

  Thank you

• 
  @waqasbtm12 ай бұрын

  thanks for explanation

• 
  @StuartsShed2 ай бұрын

  Great project - top execution. 👍👍👍👍

• 
  @dejanvanevski43993 ай бұрын

  Can this grinder be used to sharpen endmills?

• 
  @shedmade32642 ай бұрын

  It can sharpen 4 flute tap and core drills with the correct cam - no mention of end mills. So I guess not If anyone knows better please comment. All the best Shed guy

• 
  @DK-vx1zc3 ай бұрын

  nicely done! enjoyable

• 
  @shedmade32643 ай бұрын

  cheers for that there's more to come ... believe me

• 
  @ashwinpanchal7103 ай бұрын

  👍👍👍👍👍

• 
  @igorrojo73294 ай бұрын

  Hello friend, I also bought a machine just like yours, but it only comes with attachment number 2, do you know where I can buy the other three missing ones? thank you very much.

• 
  @shedmade32644 ай бұрын

  hunt around used machinery dealers ...... you come across stuff when you least expect it good luck

• 
  @RustyInventions-wz6ir5 ай бұрын

  Very nice work. I like the way you reclaim metal and don’t give up when you’re machine didn’t work to your standard

• 
  @RustyInventions-wz6ir5 ай бұрын

  Quite a extensive job you are doing. Nice work.

• 
  @tomstimenorfolk46875 ай бұрын

  Hi I have one of these, they’re great. If the drill was held in a smaller diameter holder all would be ok! As the chuck jaws would be out of the way!

• 
  @shedmade32644 ай бұрын

  Yep good point little dodges make all the difference

• 
  @tilliesinabottle5 ай бұрын

  Milling wide sections of cast iron can be a real chore- and especially if a decent flatness is sought. I dulled at least two shell mills and one slab cutter milling a casting to be a scraping practice piece. This is where a tool and cutter grinder would really come in handy.

• 
  @shedmade32644 ай бұрын

  right ...... so the moral there is watch the cutters for wear cheers

• 
  @bustednuckles25 ай бұрын

  I wish I could have found a hunk of cast iron to harvest here recently when I had to order a 3 inch square piece on line. 3 inch square cast iron cost me $72 delivered to my door. No joke. 😱

• 
  @shedmade32644 ай бұрын

  That's if you can get it. Tricky to source here in the UK , and premium prices too. Having said that the stuff I am using can have voids and inclusions which are a pain all best

• 
  @khueelee40166 ай бұрын

  ✈Thanks for the video, greatly appreciated. Once again, thanks. This is such a good video! Great informative video! ῳ💡❀ Very Good my love ∰§

• 
  @nigelkee17157 ай бұрын

  Thanks for that i was wondering if the jumper was the switch for maintained and non-maintained.

• 
  @stevechessum28547 ай бұрын

  I done my apprenticeship at Smart and Brown.

• 
  @shedmade32645 ай бұрын

  wowsa fantastic. did you stay the course ... or move on to other things. Always interested in how things were back in the day shed guy

• 
  @johnwp1117 ай бұрын

  I have had a similar problem with my Wohlhaupter UP3. To date I have not been able to figure out what is wrong.

• 
  @garethedwards65197 ай бұрын

  Great informative video! Did you happen to strip and grease the spindle front bearing?

• 
  @shedmade32645 ай бұрын

  Narp but I took the cover off and had a look ... then regreased from that direction. its another order of magnitude to strip the bearing out as you then remove the shaft , and the rear bearing ..;l;;;; honestly this shaft is not rotating too fast so no big worry. Probably go there when the belt fails ... although a linked belt seems like a good option. shed guy

• 
  @adamdiaz84427 ай бұрын

  Great drill press rare machine

• 
  @shedmade32645 ай бұрын

  Cheers Adam Yep these are cracking machines. This design works a treat . If it had an MT2 taper it would not have left me ...... having said that I do miss it. Shed guy

• 
  @MarkATrombley7 ай бұрын

  At the 5 second point in the bottom left of the screen SHED is spelled wrong. Just in case you want to fix it.

• 
  @shedmade32647 ай бұрын

  Brilliant I am unleashing dyslexia on an unsuspecting world. Many thankxx my friend Shed guy

• 
  @popperkeg12347 ай бұрын

  The best drill grinder there is,I used one of these for years in the toolroom,ground all kinds of drills and taps and pilot drills,there was a good selection of cams for many angles,wish I had one now of my own as I foolishly gave mine away many years ago.

• 
  @shedmade32647 ай бұрын

  that sucks only problem is I have no excuse for blunt drills and stuff shed guy

• 
  @popperkeg12347 ай бұрын

  Nice interesting video,well planned out.About 25 years ago I had to make a new nut for the knee for my Senior as it was so worn,now after years of use a lot of backlash has formed so it could be a new nut again,toying with the idea of making a nut with an ab extra circular nut to make a backlash eliminator.

• 
  @shedmade32647 ай бұрын

  Yep something a little better would be an idea, the screw always looks a little skinny to me shed guy

• 
  @adamdiaz84427 ай бұрын

  Stunning lathe absolute quality

• 
  @adamdiaz84427 ай бұрын

  Just bought one of these

• 
  @shedmade32647 ай бұрын

  nice one Drop a comment if you find a CBN wheel that fits happy grinding

• 
  @user-yx6zf5ev1s7 ай бұрын

  Спасибо за видео, я из России, у меня есть похожий заточной станок. Пока ещё на нем не работал.

• 
  @neffk7 ай бұрын

  May I suggest some smooth and parallel jaw pliers!

• 
  @shedmade32647 ай бұрын

  cheers beers and noted Any excuse to get more stuff Shed guy

• 
  @davidbawden65677 ай бұрын

  Well-thought-out, plained and executed, nice work, thanks for sharing...

• 
  @kevinl58787 ай бұрын

  Please show machining

• 
  @uthor7078 ай бұрын

  heroic hacking!

• 
  @greasemonkeygaragewatson10698 ай бұрын

  Thanks for the video I just bought a z25 and this has helped very much in understanding how to use it correctly. and being a man from cheshire its great to see a uk based teacher putting this out there. regards Jeff

• 
  @graemewhite50298 ай бұрын

  I find the M12 coach bolts from Toolstation are a good fit in the tee slots once you file two flats on the domed head, the square on the shank fits in nicely too and they're available in several lengths.

• 
  @shedmade32647 ай бұрын

  Graeme every day is a school day necessity is the mother of invention and all that ....... genius shed guy

• 
  @shedmade32645 ай бұрын

  Graeme top tip my friend. this is a cracking hack ... and can be tweaked for other applications Shed guy Shed guy

• 
  @Rob-xi1ig8 ай бұрын

  Thanks shed guy. Just taken in a job doing these… what could possibly go wrong 😂

• 
  @martin7jd9 ай бұрын

  Thank you.

• 
  @RustyInventions-wz6ir10 ай бұрын

  Good video. Thanks

• 
  @bergertools415910 ай бұрын

  Thanks for the mention @Shed Made. Glad you were happy with your purchase!

• 
  @rickymale820310 ай бұрын

  Having different size balls is quite normal. At least, that’s what I was told 🤣

• 
  @markrainford121910 ай бұрын

  Hitler on the other hand...

• 
  @rickymale820310 ай бұрын

  @@markrainford1219 there’s always an exception 😂

• 
  @BillyWoodburn-mp9dh10 ай бұрын

  Can you sharpen a 1flute countersink with this machine

• 
  @shedmade326410 ай бұрын

  erm I reckon you could set up a cross hole countersink to the grinding wheel wheel with pure rotation of the head - no cams no movements and grinding away. if there is a single flute then it would need relief behind the cutting edge. I guess it could be done but it is heading towards a tool and cutter grinder type machine. a 4 flute, and 3 flute would use a cam to give relief - but the flat land behind the cutting edge would be a problem. again it is more tool and cutter territory I think. I watched Stefan Gotteswinter grind a countersink to make it work to his satisfaction ........ and he goes to the next level. all the best shed guy

• 
  @LCalleja11 ай бұрын

  Hi I recently got a machine very similar to yours and found you videos very informative only problem is I am missing some parts off it would you be willing to take some dimensions for me pls?

• 
  @shedmade326410 ай бұрын

  hi there yep fire away I will try to help shed guy

• 
  @LCalleja10 ай бұрын

  @@shedmade3264 thanks my machine is missing most of its accessories as it only came with 2 left hand cams :( managed to re make one right hand cam from dimensions online so any help is welcome. If there is any better way to contact you pls let me know Thanks a lot

• 
  @shedmade326410 ай бұрын

  Hi Yep ...... if I put my email out there I will get all sorts of stuff coming through. So I will post through KZread. tell me which parts you need and I will try to help. Making the cams is most definitely the trickiest thing. Shed guy@@LCalleja

• 
  @LCalleja10 ай бұрын

  @@shedmade3264 thanks I am missing all accessories anything you would be willing to take dimensions on I would be happy with. I would also be willing to make the cams if you would be willing to measure. I will probably try to post the drawings somewhere online once I gather enough information. Thanks a lot Luke