My key got wet. I dried it on the dash and followed these steps. It works great. Thank you
@zzhughesd4 күн бұрын
I’ll go here first. I should check fuses but just know it’ll be resistor. I have zero fan speeds.
@markwilliams28306 күн бұрын
I really enjoy your uploads . A really good in depth explanation that is so easy to follow and have learned a lot from watching this.I liked the way you rigged your meter using the paper clip and connector block .Worth knowing why didn't I think of that !!! thank you so much for sharing .
@iofix5 күн бұрын
Hi Mark, thanks for your comments on this, and the Clio video - glad u liked them! :)
@markwilliams28306 күн бұрын
Excellent explanation Ian.French cars are a pain when it comes to electrical faults ! Thank you for sharing .
@kazman7908Ай бұрын
Does this work for the durashift automatic gearbox models too?
@iofix28 күн бұрын
I'm not sure - best to just check if there's a similar/same component there.
@tyTy-lj5ynАй бұрын
Thank you soooo much. It worked!
@iofix28 күн бұрын
Glad it helped!
@user-jd4kp3lp9rАй бұрын
I have 10.2 resistance value for antenna
@JackBlack444Ай бұрын
When you changed the bobine does it need go to the garage to reprogram and is it the same with the map sensor?
@iofixАй бұрын
I did not have to re-program anything.
@felixwoukec3902Ай бұрын
I have to press brake pedal to reset so thanks for info!
@iofixАй бұрын
Ok cool, thanks for the feedback.
@waladamek7098Ай бұрын
Luckily I had bookmarked this video as I've just had to repeat it and required a gentle reminder. 06 Vectra.
@iofixАй бұрын
Great glad it helped - good thinking with the bookmark!
@poetuliradiantАй бұрын
23mm deep socket to take the sensor out?
@user-ft3gv7dc3uАй бұрын
Thanks bro, everything worked out
@TheUltimate65Ай бұрын
I get varing insp 1000 when the ignition one , in short time but not over the numers how long the car have rum in km , its that the same solotion here, i change oil and filters in 207000 after a flush of engine and filiterreplement , i not reset the service this time , no have the car run 215000 since 2023.08 ,and i replement the oil and filter after flush of engine 7000 the service intervall say 300000 interval , not nownone reconmanded , but 150000 its more normal intervall
@garvie882 ай бұрын
Thank you for the video, would never have attempted this without your help. Replaced and working great
@iofixАй бұрын
Glad it helped - sorry for the late reply.
@flavacreations2 ай бұрын
This must be the older models
@alisajjad28492 ай бұрын
Anyone know how to remove the actual boot handle ?
@amandajarvis40092 ай бұрын
Thank you for this video, I amazed my husband replacing the blower motor with this, I'm now a super star, mine was slightly different being the air con version, just an extra plug really, We now have air perfect thank you.
@iofix2 ай бұрын
Great, glad the video helped u! :)
@stephenprice352 ай бұрын
Hi. Would this work on an astra J ?
@Triokrucils32 ай бұрын
This make problem AC can't running cause -40 °C?
@AngelEyes_552 ай бұрын
Does anyone know if the boot lid is supposed to spring open all the way on its own, after pressing the release button (either on the remote or the boot lid itself)? I've replace my gas struts and it STILL does not pop open like I would expect it to. Any thoughts?
@iofix2 ай бұрын
I don't believe they are no.
@AngelEyes_552 ай бұрын
Hmmmm. It's a poor effort from Audi. Thanks mate.
@hschuiling2 ай бұрын
Thanks for sharing. With help of your video I have been able to replace the abs sensor and have fixed the issue. I ordered the original part on eBay as well, had some trouble to mount it back on but with a little help of some wood and a large metal ring and a hammer I got it back on.
@iofix2 ай бұрын
Glad it helped.
@anthonywbarrios2 ай бұрын
Thanks! Worked a treat
@iofix2 ай бұрын
Glad it helped u!
@g0bzy2 ай бұрын
Great video. This was really helpful. A couple of my findings in case it helps anyone out there. My car is a 58 plate UK RHD. So its getting old!. The plastic side parts that goes to the windscreen could be pulled upward without any tools. Those came out with a bit of gentle force. The main problem i had was unblocking the drain pipes and wiper arm removal. Getting the wiper arm nuts off was easy but the arms refused to come off after years of corrosion, even with WD40 applied. Had to buy a pulling tool from a local shop (as you suggested), and that then did the trick. Drivers side drain pipe was blocked but unblocked easily using stiff bit of copper wire with tape wrapped around the end so it wasn't sharp. But the passenger side was totally blocked and would not shift. In the end, i used boiling hot water in the hole and a plumbers cleaning tool, like a brush on a flexible pipe. Eventually it shifted it!. Loads of black crud came out the bottom.. Then finished up with a hose pipe and flushed both drains through. Done. Now how does this long rubber seal clip back into place along the scuttle tray? Just seems to sit there without any clips along the front? assume it just sits there..
@iofix2 ай бұрын
Thanks for the extra info. Re that rubber seal... think it's supposed to clip onto the sound deadening moulding, but on mine that moulding has lost it's rigidity so I have that moulding cable tied to the plastic cowling to hold it in place, then the rubber seal, in the centre portion anyway, just sits on top. I've had it like that for a few years now!
@g0bzy2 ай бұрын
@@iofix That makes sense, yes the sound deading on mine is also totally floppy in the middle area and wont fix to the rubber seal. So cables ties it is !! Cheers.
@highlightedcomment2 ай бұрын
Googled how to operate a 2000 ML 320 key fob. This was their answer lol...
@wendywhales23103 ай бұрын
Hi... Been watching another video where they are replacing bulbs in the panel at the top above the radio. With this top peoce removed. Would you have access to the Resistor for the blower motor.??.
@iofix2 ай бұрын
Hi, no I don't think so.
@captkev7373 ай бұрын
Thank you, windows fixed
@iofix2 ай бұрын
Great glad it helped! :)
@williamcool24113 ай бұрын
Thanks it worked first try
@iofix2 ай бұрын
Glad it helped :)
@markzed663 ай бұрын
Your steps worked a treat. Both low beam bulbs replaced within 20 mins and $30. Imagine what Hyundai would have stung me for the same. Excellent vid. 👍
@iofix2 ай бұрын
Excellent, glad it helped u :)
@pacman-qt1ix3 ай бұрын
My ml350 want shirt pass 1st what should be done
@cindywhite68023 ай бұрын
So smart, thank you! I knew why it was happening but this simple solution hadn't occurred to me!
@iofix3 ай бұрын
Great - glad it helped u! :)
@seankenyononline7743 ай бұрын
Wow, wow wow! That worked an absolute treat. Electric windows and mirrors working again. Thanks so much 👍💯
@iofix3 ай бұрын
Excellent - glad it helped u!
@ViktorGorovelli3 ай бұрын
Thank youuu. 😊
@iofix3 ай бұрын
U're welcome - glad it helped u.
@adomasvalanciauskas76353 ай бұрын
Wow, i can't believe it helped! Visualy there was nothing wrong, but it wasnt working at all, after this cleaning all the buttons fully working! Many thanks!!!! :)
@iofix3 ай бұрын
Excellent! :)
@eduardovelasquez55113 ай бұрын
If I lost my key fob how do I replace and get a new one ?
@sandboxsam60534 ай бұрын
I never normally comment on videos, however this SAVED my car. Super clear video, worked with my Kia Picanto 2010 - I found if you know what the cable feels like, you can open the fuse compartment and reach round to unclip and re-clip the wire without taking apart the car. Super helpful video!!
@iofix4 ай бұрын
Thanks for the comment and the extra info! :)
@art24114 ай бұрын
Thank You so much man. I was just gettin to crazy about stupid battery change.
@iofix4 ай бұрын
Great glad it helped!
@DAMN__________4 ай бұрын
Hey are those not fuel injectors? Are they still called spark plugs?
@rusty911s24 ай бұрын
Brilliant! Sounds exactly the same as my 2003 Hyundai Terracan (probably the same part). In my case it has had this issue twice (crank, no start). Both times after being laid up in a damp corner of the yard for a few months. There was one point where the inside looked very damp indeed, so perfect conditions for encouraging contact corrosion. Each time it's been towed out in front of my workshop in the sun and a few days later started fine. It was only the other day I noticed the lack of immobiliser key symbol when it didn't start, and when symbol there, it starts perfectly. In light of this video will pull the coil, test and if O.K. refit after a dose of contact cleaner and a good wiggle! Thanks again 🙂
@iofix4 ай бұрын
Thanks for the comment and extra info - sorry for the late reply.
@robertcollins70344 ай бұрын
My mini is say minus 40 too in March uk 😂
@augustisalman80274 ай бұрын
Thank you ❤
@nicolapaolobello9824 ай бұрын
Thank you very much,you helped me ,I had the same problem.
@lupitasantiago5 ай бұрын
Omg thank you so much 😊
@trickyfocus5 ай бұрын
This happened to my Sportage so i soldered the two coil wires to each other and bypassed the connector its a lot easier on the Sportage
@DannyCKJ5 ай бұрын
Great vid man thankyou only one cud find aswell :)
@Bored.Exe695 ай бұрын
Or ignore
@samnunn82915 ай бұрын
Will this work on. Vauxhall combo van 2019???
@iofix5 ай бұрын
Not sure.
@tedjohnson645 ай бұрын
Excellent demo!
@iofix5 ай бұрын
Thanks
@MagicznyMuchomor5 ай бұрын
Great film. Very handy!
@iofix5 ай бұрын
Glad u found it helpful :)
@johannessilver86535 ай бұрын
I have 1999 Megane and the horn is on the left (drivers side) and under ...one can get pretty easy into it. It gets power by wires but give not sound.
@iofix5 ай бұрын
If the power and ground are both good then it should just be a matter of replacing the horn unit.
@user-ny6lz2gf6e5 ай бұрын
Thanks bud! Thankfully I discovered your method myself by accident after I saw the video that required bumper removal. This is a super helpful tip for those who are going down that road! Cheers from New Zealand - Mitch
Пікірлер
My key got wet. I dried it on the dash and followed these steps. It works great. Thank you
I’ll go here first. I should check fuses but just know it’ll be resistor. I have zero fan speeds.
I really enjoy your uploads . A really good in depth explanation that is so easy to follow and have learned a lot from watching this.I liked the way you rigged your meter using the paper clip and connector block .Worth knowing why didn't I think of that !!! thank you so much for sharing .
Hi Mark, thanks for your comments on this, and the Clio video - glad u liked them! :)
Excellent explanation Ian.French cars are a pain when it comes to electrical faults ! Thank you for sharing .
Does this work for the durashift automatic gearbox models too?
I'm not sure - best to just check if there's a similar/same component there.
Thank you soooo much. It worked!
Glad it helped!
I have 10.2 resistance value for antenna
When you changed the bobine does it need go to the garage to reprogram and is it the same with the map sensor?
I did not have to re-program anything.
I have to press brake pedal to reset so thanks for info!
Ok cool, thanks for the feedback.
Luckily I had bookmarked this video as I've just had to repeat it and required a gentle reminder. 06 Vectra.
Great glad it helped - good thinking with the bookmark!
23mm deep socket to take the sensor out?
Thanks bro, everything worked out
I get varing insp 1000 when the ignition one , in short time but not over the numers how long the car have rum in km , its that the same solotion here, i change oil and filters in 207000 after a flush of engine and filiterreplement , i not reset the service this time , no have the car run 215000 since 2023.08 ,and i replement the oil and filter after flush of engine 7000 the service intervall say 300000 interval , not nownone reconmanded , but 150000 its more normal intervall
Thank you for the video, would never have attempted this without your help. Replaced and working great
Glad it helped - sorry for the late reply.
This must be the older models
Anyone know how to remove the actual boot handle ?
Thank you for this video, I amazed my husband replacing the blower motor with this, I'm now a super star, mine was slightly different being the air con version, just an extra plug really, We now have air perfect thank you.
Great, glad the video helped u! :)
Hi. Would this work on an astra J ?
This make problem AC can't running cause -40 °C?
Does anyone know if the boot lid is supposed to spring open all the way on its own, after pressing the release button (either on the remote or the boot lid itself)? I've replace my gas struts and it STILL does not pop open like I would expect it to. Any thoughts?
I don't believe they are no.
Hmmmm. It's a poor effort from Audi. Thanks mate.
Thanks for sharing. With help of your video I have been able to replace the abs sensor and have fixed the issue. I ordered the original part on eBay as well, had some trouble to mount it back on but with a little help of some wood and a large metal ring and a hammer I got it back on.
Glad it helped.
Thanks! Worked a treat
Glad it helped u!
Great video. This was really helpful. A couple of my findings in case it helps anyone out there. My car is a 58 plate UK RHD. So its getting old!. The plastic side parts that goes to the windscreen could be pulled upward without any tools. Those came out with a bit of gentle force. The main problem i had was unblocking the drain pipes and wiper arm removal. Getting the wiper arm nuts off was easy but the arms refused to come off after years of corrosion, even with WD40 applied. Had to buy a pulling tool from a local shop (as you suggested), and that then did the trick. Drivers side drain pipe was blocked but unblocked easily using stiff bit of copper wire with tape wrapped around the end so it wasn't sharp. But the passenger side was totally blocked and would not shift. In the end, i used boiling hot water in the hole and a plumbers cleaning tool, like a brush on a flexible pipe. Eventually it shifted it!. Loads of black crud came out the bottom.. Then finished up with a hose pipe and flushed both drains through. Done. Now how does this long rubber seal clip back into place along the scuttle tray? Just seems to sit there without any clips along the front? assume it just sits there..
Thanks for the extra info. Re that rubber seal... think it's supposed to clip onto the sound deadening moulding, but on mine that moulding has lost it's rigidity so I have that moulding cable tied to the plastic cowling to hold it in place, then the rubber seal, in the centre portion anyway, just sits on top. I've had it like that for a few years now!
@@iofix That makes sense, yes the sound deading on mine is also totally floppy in the middle area and wont fix to the rubber seal. So cables ties it is !! Cheers.
Googled how to operate a 2000 ML 320 key fob. This was their answer lol...
Hi... Been watching another video where they are replacing bulbs in the panel at the top above the radio. With this top peoce removed. Would you have access to the Resistor for the blower motor.??.
Hi, no I don't think so.
Thank you, windows fixed
Great glad it helped! :)
Thanks it worked first try
Glad it helped :)
Your steps worked a treat. Both low beam bulbs replaced within 20 mins and $30. Imagine what Hyundai would have stung me for the same. Excellent vid. 👍
Excellent, glad it helped u :)
My ml350 want shirt pass 1st what should be done
So smart, thank you! I knew why it was happening but this simple solution hadn't occurred to me!
Great - glad it helped u! :)
Wow, wow wow! That worked an absolute treat. Electric windows and mirrors working again. Thanks so much 👍💯
Excellent - glad it helped u!
Thank youuu. 😊
U're welcome - glad it helped u.
Wow, i can't believe it helped! Visualy there was nothing wrong, but it wasnt working at all, after this cleaning all the buttons fully working! Many thanks!!!! :)
Excellent! :)
If I lost my key fob how do I replace and get a new one ?
I never normally comment on videos, however this SAVED my car. Super clear video, worked with my Kia Picanto 2010 - I found if you know what the cable feels like, you can open the fuse compartment and reach round to unclip and re-clip the wire without taking apart the car. Super helpful video!!
Thanks for the comment and the extra info! :)
Thank You so much man. I was just gettin to crazy about stupid battery change.
Great glad it helped!
Hey are those not fuel injectors? Are they still called spark plugs?
Brilliant! Sounds exactly the same as my 2003 Hyundai Terracan (probably the same part). In my case it has had this issue twice (crank, no start). Both times after being laid up in a damp corner of the yard for a few months. There was one point where the inside looked very damp indeed, so perfect conditions for encouraging contact corrosion. Each time it's been towed out in front of my workshop in the sun and a few days later started fine. It was only the other day I noticed the lack of immobiliser key symbol when it didn't start, and when symbol there, it starts perfectly. In light of this video will pull the coil, test and if O.K. refit after a dose of contact cleaner and a good wiggle! Thanks again 🙂
Thanks for the comment and extra info - sorry for the late reply.
My mini is say minus 40 too in March uk 😂
Thank you ❤
Thank you very much,you helped me ,I had the same problem.
Omg thank you so much 😊
This happened to my Sportage so i soldered the two coil wires to each other and bypassed the connector its a lot easier on the Sportage
Great vid man thankyou only one cud find aswell :)
Or ignore
Will this work on. Vauxhall combo van 2019???
Not sure.
Excellent demo!
Thanks
Great film. Very handy!
Glad u found it helpful :)
I have 1999 Megane and the horn is on the left (drivers side) and under ...one can get pretty easy into it. It gets power by wires but give not sound.
If the power and ground are both good then it should just be a matter of replacing the horn unit.
Thanks bud! Thankfully I discovered your method myself by accident after I saw the video that required bumper removal. This is a super helpful tip for those who are going down that road! Cheers from New Zealand - Mitch
👍