Hello, oil change will be done next week. My pump leaked in the same way. The engine is new and only 2000 km. Why did you add atf oil? It will be changed with 10w60 castol. 🎉
@BurninGas8.13 сағат бұрын
Because atf breaks down sludge the v10 is known for sludging the crank journals and wiping bearings out
@BurninGas8.13 сағат бұрын
And I use liqui moly
@radaresat3 сағат бұрын
@@BurninGas8.1 Should I add it to Castrol, what is your advice?
@heathcarr1105Күн бұрын
Clearly dude has never seen a driveshaft explode by how comfortable he is standing right beside it
@genesisboy9282Күн бұрын
I have the same problem with my E38 730i 1995 (mechanical throttle position) I checked if there's any vacuum leaking and it was fine , I changed the IAC and still same problem ! By the way I noticed that when I open the oil cap the RPM goes up and there will be a high vacuum noise coming from the PCV so I changed the PCV ( cheep one ) and still the same problem RPM vibrating Is there and solution ? 😔
@paulsmith2105Күн бұрын
Ya buddy real torque
@Zackthefanman76Күн бұрын
Damn you’re making me want to buy an ls 400 right now
@fomocomofo5694Күн бұрын
Fuckin Lyft a Chevy a few feet make it REALLY stiff get 2 d80s and a some rock bounceing shit for the front end and 47s with 1000hp 632
@fomocomofo5694Күн бұрын
Find old logging roads or skitter trails or where a dozer once was ! I presume most logging roads don’t have rock in em around there !
@fomocomofo5694Күн бұрын
Go off the COCKSUCKIN rode !!!
@fomocomofo5694Күн бұрын
Where is this place?
@fomocomofo5694Күн бұрын
This is frome saint Hellen’s Oregon ! Btw
@mattdeterman7675Күн бұрын
Why arent your guys hubs locked in the second you get off the pavement???
@jhenry7406Күн бұрын
Had an8.1 in a GMC 4x4with an Alison trans,thing would pull a house down if you wanted,lite the tires doing 25 mph.bone stock
@VXLDUDE2 күн бұрын
I have the same issue as the vehicle in the video. I replaced speed sensor and wheel bearing on left front wheel. Still getting C0031-1D code. It says wheel speed is 0 mph on live data on left front wheel.
@BurninGas8.12 күн бұрын
Then something is wrong broken wire in harness maybe or bearing in backwards
@VXLDUDEКүн бұрын
@@BurninGas8.1 is it possible I over torqued the axle nut when I installed the bearing? Should I start testing wires starting with the other end of the plug to the speed sensor?
@Charles-sb2wq2 күн бұрын
Nice let's see some donuts..
@Thatslowg2 күн бұрын
Brother that’s a tourqe converter 😂😂😂😂😂
@hansenartwik15742 күн бұрын
Tell me you dont mind replacing a clutch and trans without telling me
@BurninGas8.12 күн бұрын
It’s auto lol
@hansenartwik15742 күн бұрын
@@BurninGas8.1 even worse!! Haha
@BurninGas8.12 күн бұрын
@@hansenartwik1574 absolutely
@THREEofFOUR342 күн бұрын
Serious way to mess up your car
@BurninGas8.12 күн бұрын
It’s a truck
@outfield19882 күн бұрын
Stupid
@jayshotyt41352 күн бұрын
🫵🤡
@jacobgreasemonkey.k42692 күн бұрын
Ummmm yes sir I'll take 2 please 😂
@902hand73 күн бұрын
Nice work fellas 👍👍
@BurninGas8.13 күн бұрын
Thanks brother
@Frontireadventures3 күн бұрын
Saunders still sell Husqvarna?
@BurninGas8.13 күн бұрын
No Collin hughes
@Frontireadventures4 күн бұрын
She's a beast.
@BurninGas8.13 күн бұрын
Thanks buddy
@jeanmarcleblanc92864 күн бұрын
You guys are machines 💪🪵💪 the #logfather will give you extra credit for getting soaked
@BurninGas8.14 күн бұрын
Yup we weren’t stopping lol
@Frontireadventures4 күн бұрын
Givin er....the days I remember.
@slickmuck43124 күн бұрын
Sounds soooo good😊😊
@Klipz69425 күн бұрын
U fucking went at er
@BurninGas8.15 күн бұрын
I don’t play around
@Klipz69424 күн бұрын
@@BurninGas8.1 lol ain't it
@manuelramirez82035 күн бұрын
The 5.0 the best engine ever produced!
@BurninGas8.15 күн бұрын
This year it turns on for sure
@manuelramirez82034 күн бұрын
@@BurninGas8.1 look up borla atak with long tube headers
@charlesb42675 күн бұрын
In the up coming video will there be a tire wear review, where you swear you have been "rotating" your tires ? 😅
@BurninGas8.15 күн бұрын
I don’t do that stuff
@charlesb42675 күн бұрын
@@BurninGas8.1 Thats a joke by the way, just re read it with that in mind LOL.
@paulcondie25205 күн бұрын
Wash the windshield! 😂😂😂 Thing sounds badass!
@BurninGas8.15 күн бұрын
its fly season here
@paulcondie25205 күн бұрын
@@BurninGas8.1 lol, I get it.
@kevinjoyner40445 күн бұрын
Love it had two square body chevys just awesome
@Frontireadventures5 күн бұрын
Dog n pony show.😂😂
@austinwilbanks59195 күн бұрын
I think some vehicles just have to be benched tuned. I pulled: 1. Radio 2. Radio Amp 3. Info 4. SEO B1 5 SEO Ign Wrote slow speed failed the erase step and boom lost everything. I got a bench tuner coming so I can recover it and it’s bad that it’s my sister’s fiancée’s truck. I feel bad but wtf is this issue
@BurninGas8.15 күн бұрын
I wouldn’t of pulled ignition fuse
@austinwilbanks59195 күн бұрын
@@BurninGas8.1 I was just trying everything I could find on the forums lol it started with the 1st three then one post swears he did the other two as well and worked like a charm. That was a lie 😂
@BurninGas8.15 күн бұрын
@@austinwilbanks5919 that’s frustrating sonetimes the ecu can just fry for no reason at all I have a lot of stock tunes if you need a file
@NicoleFitz-tq5sk6 күн бұрын
I took it in and got new spark plugs and coil and now this happened with the turbo I’m not sure if the guy is trying to rip me off
@NicoleFitz-tq5sk6 күн бұрын
My Honda has that many miles and my turbo is making a weird whistling noise and the car is struggling to accelerate
@edithscheuringer58476 күн бұрын
I've a 540i from 97 with ecu and catless, is quicker than the 540i with d vanos and take 9-16 ltr, great car❤
@BurninGas8.15 күн бұрын
Yea I’ve got 315 gears in mine
@OldGuy70s6 күн бұрын
I use to go camping not far from there, at Shore Boat View Campgrounds, in Bayport... cool
@user-zl2nb9hy3i6 күн бұрын
5.0 have the posi switch
@BurninGas8.15 күн бұрын
no it just hits post
@mmiller11886 күн бұрын
Gearing and frame flex worked great for these old trucks.
@OldGuy70s6 күн бұрын
Hey from N.B............
@BurninGas8.16 күн бұрын
Hey bro
@gregrogers30306 күн бұрын
Man your truck looks cool and it sounds and performs awesome. Good choice for the 6.0 swap.
@BurninGas8.16 күн бұрын
Thanks buddy check out my playlist for it
@ruttlicker11392 күн бұрын
The 6.0 is such a great motor..This is basically my dream truck if it was white,had an NV4500 and was on 38.5s…An atlas would be cool too but dual cases would be okay as well or another aftermarket case with multiple gear choices
@josegmaya16616 күн бұрын
Fuken badasss 🔥🔥🔥🔥🔥🔥
@mikes12927 күн бұрын
Bad ass 5.0 fun
@BurninGas8.17 күн бұрын
Things nuts
@jimthomas19897 күн бұрын
It doesn't matter what size engine you have , if you have street tires , you are not going too many places , Now Mud tires will take you any place you want to go , I put a set of SuperSwampers on a 4X4 S-10 Truck and I haven't been stuck since 2008 That's 16 years
@BurninGas8.17 күн бұрын
My other truck has a winch worst case only minutes away and my diffs are welded so she takes a good bite I can’t drive around hauling a 7 ton trailer on superswampers on pavement lol
@ruttlicker11392 күн бұрын
You clearly don’t hit any real trails if you haven’t been stuck in 16 years and if you think a set of mud tires is going to make your truck unstoppable you’re living in a fantasy..Swampers aren’t anything special..You’re comment showed you don’t know what you’re talking about and just like to talk on the internet
@jasont20747 күн бұрын
Great review, thanks bud
@BurninGas8.17 күн бұрын
check out the seadoo playlist
@cheechindiesel7 күн бұрын
Man I miss mudding trucks with buddy’s those were the days
@MilesG60108 күн бұрын
If I ever got a jet ski I would get a Yamaha
@walkerpage17018 күн бұрын
That mf stock ash
@BurninGas8.18 күн бұрын
?
@walkerpage17018 күн бұрын
@@BurninGas8.1 she ain’t cammed brotha
@BurninGas8.17 күн бұрын
@@walkerpage1701 shows your knowledge raylar bp 203 and roller rockers
@BurninGas8.17 күн бұрын
maybe watch the video where I tear the motor out and install it lmfao
@taylordean98678 күн бұрын
Good job carson
@FreshieAlbanian9 күн бұрын
The exact same thing has just happened to me. I put a new slave cylinder and my transmission kept acting up until one day it locked me out completely. Slave cylinder stuck in fork, made a hole. It also leaked everywhere. I haven’t opened the transmission yet, do you think the pivot bushing was the cause? How would over extension cause a hole? Do you think the slave cylinder was leaking after the over extension or before? Hopefully my release bearing/clutch is OK as I had under 2000miles with them
@FreshieAlbanian9 күн бұрын
Also, do you recommend a plastic pivot bushing then?
@BurninGas8.19 күн бұрын
Plastic for sure brass is no good watch my bmw playlist the worn pivot causes slave to over extend essentially blowing the seals out of it
@FreshieAlbanian8 күн бұрын
@@BurninGas8.1 what else do you recommend replacing? was your pressure plate fine? So far I have - Slave Cylinder - Plastic pivot Bearing / Clip also did you apply any grease anywhere
@BurninGas8.18 күн бұрын
@@FreshieAlbanian no grease and put a new throw out bearing in if fork is damaged replace it as well
@rogermyers35319 күн бұрын
but they are not throwing mud, but i hate mud, or cleaning it up
Пікірлер
Hello, oil change will be done next week. My pump leaked in the same way. The engine is new and only 2000 km. Why did you add atf oil? It will be changed with 10w60 castol. 🎉
Because atf breaks down sludge the v10 is known for sludging the crank journals and wiping bearings out
And I use liqui moly
@@BurninGas8.1 Should I add it to Castrol, what is your advice?
Clearly dude has never seen a driveshaft explode by how comfortable he is standing right beside it
I have the same problem with my E38 730i 1995 (mechanical throttle position) I checked if there's any vacuum leaking and it was fine , I changed the IAC and still same problem ! By the way I noticed that when I open the oil cap the RPM goes up and there will be a high vacuum noise coming from the PCV so I changed the PCV ( cheep one ) and still the same problem RPM vibrating Is there and solution ? 😔
Ya buddy real torque
Damn you’re making me want to buy an ls 400 right now
Fuckin Lyft a Chevy a few feet make it REALLY stiff get 2 d80s and a some rock bounceing shit for the front end and 47s with 1000hp 632
Find old logging roads or skitter trails or where a dozer once was ! I presume most logging roads don’t have rock in em around there !
Go off the COCKSUCKIN rode !!!
Where is this place?
This is frome saint Hellen’s Oregon ! Btw
Why arent your guys hubs locked in the second you get off the pavement???
Had an8.1 in a GMC 4x4with an Alison trans,thing would pull a house down if you wanted,lite the tires doing 25 mph.bone stock
I have the same issue as the vehicle in the video. I replaced speed sensor and wheel bearing on left front wheel. Still getting C0031-1D code. It says wheel speed is 0 mph on live data on left front wheel.
Then something is wrong broken wire in harness maybe or bearing in backwards
@@BurninGas8.1 is it possible I over torqued the axle nut when I installed the bearing? Should I start testing wires starting with the other end of the plug to the speed sensor?
Nice let's see some donuts..
Brother that’s a tourqe converter 😂😂😂😂😂
Tell me you dont mind replacing a clutch and trans without telling me
It’s auto lol
@@BurninGas8.1 even worse!! Haha
@@hansenartwik1574 absolutely
Serious way to mess up your car
It’s a truck
Stupid
🫵🤡
Ummmm yes sir I'll take 2 please 😂
Nice work fellas 👍👍
Thanks brother
Saunders still sell Husqvarna?
No Collin hughes
She's a beast.
Thanks buddy
You guys are machines 💪🪵💪 the #logfather will give you extra credit for getting soaked
Yup we weren’t stopping lol
Givin er....the days I remember.
Sounds soooo good😊😊
U fucking went at er
I don’t play around
@@BurninGas8.1 lol ain't it
The 5.0 the best engine ever produced!
This year it turns on for sure
@@BurninGas8.1 look up borla atak with long tube headers
In the up coming video will there be a tire wear review, where you swear you have been "rotating" your tires ? 😅
I don’t do that stuff
@@BurninGas8.1 Thats a joke by the way, just re read it with that in mind LOL.
Wash the windshield! 😂😂😂 Thing sounds badass!
its fly season here
@@BurninGas8.1 lol, I get it.
Love it had two square body chevys just awesome
Dog n pony show.😂😂
I think some vehicles just have to be benched tuned. I pulled: 1. Radio 2. Radio Amp 3. Info 4. SEO B1 5 SEO Ign Wrote slow speed failed the erase step and boom lost everything. I got a bench tuner coming so I can recover it and it’s bad that it’s my sister’s fiancée’s truck. I feel bad but wtf is this issue
I wouldn’t of pulled ignition fuse
@@BurninGas8.1 I was just trying everything I could find on the forums lol it started with the 1st three then one post swears he did the other two as well and worked like a charm. That was a lie 😂
@@austinwilbanks5919 that’s frustrating sonetimes the ecu can just fry for no reason at all I have a lot of stock tunes if you need a file
I took it in and got new spark plugs and coil and now this happened with the turbo I’m not sure if the guy is trying to rip me off
My Honda has that many miles and my turbo is making a weird whistling noise and the car is struggling to accelerate
I've a 540i from 97 with ecu and catless, is quicker than the 540i with d vanos and take 9-16 ltr, great car❤
Yea I’ve got 315 gears in mine
I use to go camping not far from there, at Shore Boat View Campgrounds, in Bayport... cool
5.0 have the posi switch
no it just hits post
Gearing and frame flex worked great for these old trucks.
Hey from N.B............
Hey bro
Man your truck looks cool and it sounds and performs awesome. Good choice for the 6.0 swap.
Thanks buddy check out my playlist for it
The 6.0 is such a great motor..This is basically my dream truck if it was white,had an NV4500 and was on 38.5s…An atlas would be cool too but dual cases would be okay as well or another aftermarket case with multiple gear choices
Fuken badasss 🔥🔥🔥🔥🔥🔥
Bad ass 5.0 fun
Things nuts
It doesn't matter what size engine you have , if you have street tires , you are not going too many places , Now Mud tires will take you any place you want to go , I put a set of SuperSwampers on a 4X4 S-10 Truck and I haven't been stuck since 2008 That's 16 years
My other truck has a winch worst case only minutes away and my diffs are welded so she takes a good bite I can’t drive around hauling a 7 ton trailer on superswampers on pavement lol
You clearly don’t hit any real trails if you haven’t been stuck in 16 years and if you think a set of mud tires is going to make your truck unstoppable you’re living in a fantasy..Swampers aren’t anything special..You’re comment showed you don’t know what you’re talking about and just like to talk on the internet
Great review, thanks bud
check out the seadoo playlist
Man I miss mudding trucks with buddy’s those were the days
If I ever got a jet ski I would get a Yamaha
That mf stock ash
?
@@BurninGas8.1 she ain’t cammed brotha
@@walkerpage1701 shows your knowledge raylar bp 203 and roller rockers
maybe watch the video where I tear the motor out and install it lmfao
Good job carson
The exact same thing has just happened to me. I put a new slave cylinder and my transmission kept acting up until one day it locked me out completely. Slave cylinder stuck in fork, made a hole. It also leaked everywhere. I haven’t opened the transmission yet, do you think the pivot bushing was the cause? How would over extension cause a hole? Do you think the slave cylinder was leaking after the over extension or before? Hopefully my release bearing/clutch is OK as I had under 2000miles with them
Also, do you recommend a plastic pivot bushing then?
Plastic for sure brass is no good watch my bmw playlist the worn pivot causes slave to over extend essentially blowing the seals out of it
@@BurninGas8.1 what else do you recommend replacing? was your pressure plate fine? So far I have - Slave Cylinder - Plastic pivot Bearing / Clip also did you apply any grease anywhere
@@FreshieAlbanian no grease and put a new throw out bearing in if fork is damaged replace it as well
but they are not throwing mud, but i hate mud, or cleaning it up
Did you put your own motor together?
In my trucks yes sir
@@BurninGas8.1 sounds sweet 😎