I think the 77 bay I just bought has had the smaller torsion leafs bulled out . 😢
@MOGODDTHEFIXER4 күн бұрын
But it still drives smooth or
@antoniopalmero40634 күн бұрын
@@MOGODDTHEFIXER my tyres rub in the front tubs 😂
@MOGODDTHEFIXER3 күн бұрын
@@antoniopalmero4063 lol, Eish sorry man
@antoniopalmero40633 күн бұрын
@@MOGODDTHEFIXER I’ll take a closer look today , the rear looks lower too . Seems to be about 2 inches or so lower than my other bay . I got the pair for well under £9k so not too worried as they both run and drive ok and are solid underneath etc .
@jerrienyembe12 күн бұрын
Why ur pistol caps or on different direction?...am nt abt using paint scrapper. If its works fr u
@MOGODDTHEFIXER5 күн бұрын
They are correct, watch the full video
@whitestar353118 күн бұрын
Thanks man
@MOGODDTHEFIXER17 күн бұрын
You welcome stay tuned
@ct9240418 күн бұрын
Hi, I have a question and was wondering if you could help. I'm trying to restore a 1972 Super Beetle. I just put in a new pedal assembly and connected the clutch cable. (The engine and clutch are not installed yet). I THINK I did it right, I tightened the cable and the lever on the transmission moves when the pedal is pressed. But I'm wondering, how much does the throw out bearing have to travel for the clutch to work? I'm totally new to this and I hope I did it right!
@MOGODDTHEFIXER17 күн бұрын
Hi, take your time bit bit and enjoy it, I see you say you did not install the clutch kit, meaning that even if you press the clutch pedal it will just move cause there is nothing to disengage the transition of power from the engine to the gearbox.
@deaguzaza108829 күн бұрын
The godfather, you must borrow me.
@MOGODDTHEFIXER29 күн бұрын
Come and take it, it will suit you
@kembemumba1534Ай бұрын
Great explanation man❤
@MOGODDTHEFIXERАй бұрын
Thanks stay tuned.
@user-ic6st4ew9uАй бұрын
سياره 2016 سياره مميزه وعليك اتباع الخطوات المناسبه لتصليح المحرك فهناك بعض الملاحظات مثلا وضع اوراق من الكاسكيت حول البوشه السلندر وكذلك الاسطوانه تحياتي
@MOGODDTHEFIXERАй бұрын
Thanks i will do that, stay tuned it might take a while but I will get it done.
@babelonchabalala1690Ай бұрын
Got a tip from a clutch specialist.... If the clearance between the pressure forks and the release bearing is too big you must add shims or a washer on each bolt between pressure plate and flywheel, otherwise you will find hard to get gears.... This especially happen when you resurfaced (skimmed) the pressure plate
@MOGODDTHEFIXERАй бұрын
I once did that and it worked, thanks very much for the knowledge.
@OSIRISSAАй бұрын
This guy is not make sure. You can't come out to help us and you not sure
@MOGODDTHEFIXERАй бұрын
Sorry I couldn't help you
@emmanuelthapelo6874Ай бұрын
He can't teach us to tune a cab while he don't know the idling jet
@snarechallenge5102Ай бұрын
😴😴
@MOGODDTHEFIXERАй бұрын
Lol easy
@matsiemola6851Ай бұрын
The car looks nice, although the paint on it is gone
@MOGODDTHEFIXERАй бұрын
The owner is going to paint it, stay tuned
@MOGODDTHEFIXERАй бұрын
Thanks everyone who watched these video/clip let me know if you wanna see more of these car. I don't own the car, it's a friend's car
@TshepoTitusАй бұрын
Hello hope your good I wanted to ask how much did the bearings cost and where dd you buy them Thanks
@MOGODDTHEFIXERАй бұрын
It's been 3 years since I bought,but I think around R600 if I'm not mistaken most spare shops should have them. I will check and come back to you
@ezzelindeerling1518Ай бұрын
I have a 1962 model still running if you interested
@MOGODDTHEFIXERАй бұрын
Where are you located
@ezzelindeerling1518Ай бұрын
@@MOGODDTHEFIXER Pretoria
@MOGODDTHEFIXERАй бұрын
@@ezzelindeerling1518, please inbox me oh tit tok @Mogoddthefixer. Thanks
@willymalebati2293Ай бұрын
It's still a re-buildable car it only dirty give it your time and boom you got a nice car Ford Cortina GLs 3.0 Work on the miner problems take out the seat and clean them properly..well done
@MOGODDTHEFIXERАй бұрын
Thanks for the motivation, I will surely do that
@calvinlottering77652 ай бұрын
Hi brother could i get your contact details or FB messenger i desperately need help with my 1.6 carb....
@MOGODDTHEFIXERАй бұрын
Hi, I'm having problems with my number, what's seems to be the problem
@calvinlottering7765Ай бұрын
@MOGODDTHEFIXER it's boging down when i accelerate and it idles high i. The morning its refuses to stay it's always cutting off
@bondniko2 ай бұрын
it's a real death capsule
@MOGODDTHEFIXER2 ай бұрын
What you mean lol
@Pico_Farad2 ай бұрын
My dad had one of those.
@MOGODDTHEFIXER2 ай бұрын
It's a nice car to drive, your father has good taste
@marcpletacher35492 ай бұрын
Lui redonner une beauté a la Renault 16 ça sera génial c'était une voiture avec des qualités exceptionnelles c'est comme une vieille femme bien maquillé ça change tout
@MOGODDTHEFIXER2 ай бұрын
Merci, restez a l'ecoute
@marcpletacher35492 ай бұрын
Quel malheur de voir une Renault 16 dans l'état la Une voiture exceptionnel ❤❤
@MOGODDTHEFIXER2 ай бұрын
Je ferai de mon mieux pour lui redonner son ancienne gloire.
@costachristoo2 ай бұрын
Thank you from Greece, it was very helpful the whole video, I own a t2 1972 and I have a problem with squizing noise while I am driving, very detailed description you did thank you again
@MOGODDTHEFIXER2 ай бұрын
Glad I could help, stay tuned
@matsiemola68513 ай бұрын
Nice bus,love the gear shift extension lol
@MOGODDTHEFIXER3 ай бұрын
Thanks is easier for me to shift
@Vermeulen943 ай бұрын
Hey buddy
@MOGODDTHEFIXER3 ай бұрын
Hey
@user-pf6eb8ou2f4 ай бұрын
Bro u dont know what u talking about
@MOGODDTHEFIXER3 ай бұрын
It works for me so it should work for you
@pakomotswiri57674 ай бұрын
Hello I think you didn't go much further with some other components like jets,two pieces that seats under those jets and the float needle..thank you sir
@MOGODDTHEFIXER3 ай бұрын
Thanks for the lovely knowledge
@user-zt2wj8ib5m4 ай бұрын
I kou don't know English but i 😅 understand everything you said bro ...very great video but i can't use this method because I don't want to remove the flywheel.... but 👍🏿
@user-el8bs9vk7g5 ай бұрын
Thankyou very much sir
@MOGODDTHEFIXER5 ай бұрын
You welcome
@user-gu9jj1ur2q6 ай бұрын
Do you drive it often
@MOGODDTHEFIXER6 ай бұрын
Yeah I do
@ribamalese44257 ай бұрын
Like the way it sound
@MOGODDTHEFIXER7 ай бұрын
Thanks
@ribamalese44257 ай бұрын
I have never seen a Renault ts automatic
@MOGODDTHEFIXER7 ай бұрын
Nice car indeed
@ribamalese44257 ай бұрын
Nice car you should restore it
@user-ps9bs6jw5g7 ай бұрын
I will like to see it run please
@MOGODDTHEFIXER7 ай бұрын
Sorry but I sold it to my friend
@phemncwabe18348 ай бұрын
Thanks boss I have checked on my carburetor and only to find out that my choke cable was loose and agdusted abit. Also from your video
@MOGODDTHEFIXER8 ай бұрын
Glad I could help
@phemncwabe18348 ай бұрын
Very nice video, I have a question; My golf 1 is starting, but then dies again it only needs a rev to keep on. Would you say it's bad timing? I have checked my fuel pump but couldn't see any damage.
@MOGODDTHEFIXER8 ай бұрын
Check out my video on why your car is not idling
@user-om5oh7yf1d8 ай бұрын
Man I must admit you didn't do your homework
@thomasmofokeng92898 ай бұрын
How to set a Hi cle
@MOGODDTHEFIXER8 ай бұрын
Check out my video on how to tune your golf carburetor
@bobtomica96148 ай бұрын
Nice video. What is the fuel pressure of the pump
@MOGODDTHEFIXER8 ай бұрын
Thanks, it's about 4 psi.
@bobtomica96148 ай бұрын
@@MOGODDTHEFIXER Many Thanks!!!
@user-wr2ov5fn8p9 ай бұрын
Idling jet
@princemdu20209 ай бұрын
Whats causing petrol not to pass through the small hole when i accelerate
@siphiwejohn158210 ай бұрын
I have 2l golf engen after timing maks it cranks but never starts but it has some shoots on the exoust
@cedricmabange20239 ай бұрын
Same
@kingrhegan6 ай бұрын
could your timing be out by 180 degrees
@WADDADOO10 ай бұрын
It helped. They all haters
@anwarpalekar87310 ай бұрын
Mine does the same
@michaelkamuri548310 ай бұрын
Hi,present that,video,if possible
@MOGODDTHEFIXER10 ай бұрын
Stay tuned I will do that, thanks for watching
@NadineDavids-hb7ib10 ай бұрын
I got a problem with mine like this it don't have spark not showing desh bored lights what can the problem be
@yusofabubakar370310 ай бұрын
What happened
@MOGODDTHEFIXER10 ай бұрын
With?
@oscararredondo452310 ай бұрын
Solución?
@MOGODDTHEFIXER10 ай бұрын
@@oscararredondo4523, it was the distributor, I changed it to pointless one
@masilo706011 ай бұрын
Phu rrrrrrr. What's that
@MOGODDTHEFIXER11 ай бұрын
Lol
@masilo706011 ай бұрын
Hey Bru u trying but u r confusing me a lot. Sorry. Do more work.
@MOGODDTHEFIXER11 ай бұрын
Xo
@johnnykueyo640911 ай бұрын
Hi there,apart from the original I bought a new one but it's having extra inlets and outlets pips on it.
@MOGODDTHEFIXER11 ай бұрын
Stay tuned I will, explain more about it
@mahlatseboshielo314811 ай бұрын
Thanks that's help me lots
@mahlatseboshielo314811 ай бұрын
That means the problem is not that cap holding the diafraim?
@mahlatseboshielo314811 ай бұрын
Hi what couse the accelerator pumps to link the petrol and how to fix it?
Пікірлер
I think the 77 bay I just bought has had the smaller torsion leafs bulled out . 😢
But it still drives smooth or
@@MOGODDTHEFIXER my tyres rub in the front tubs 😂
@@antoniopalmero4063 lol, Eish sorry man
@@MOGODDTHEFIXER I’ll take a closer look today , the rear looks lower too . Seems to be about 2 inches or so lower than my other bay . I got the pair for well under £9k so not too worried as they both run and drive ok and are solid underneath etc .
Why ur pistol caps or on different direction?...am nt abt using paint scrapper. If its works fr u
They are correct, watch the full video
Thanks man
You welcome stay tuned
Hi, I have a question and was wondering if you could help. I'm trying to restore a 1972 Super Beetle. I just put in a new pedal assembly and connected the clutch cable. (The engine and clutch are not installed yet). I THINK I did it right, I tightened the cable and the lever on the transmission moves when the pedal is pressed. But I'm wondering, how much does the throw out bearing have to travel for the clutch to work? I'm totally new to this and I hope I did it right!
Hi, take your time bit bit and enjoy it, I see you say you did not install the clutch kit, meaning that even if you press the clutch pedal it will just move cause there is nothing to disengage the transition of power from the engine to the gearbox.
The godfather, you must borrow me.
Come and take it, it will suit you
Great explanation man❤
Thanks stay tuned.
سياره 2016 سياره مميزه وعليك اتباع الخطوات المناسبه لتصليح المحرك فهناك بعض الملاحظات مثلا وضع اوراق من الكاسكيت حول البوشه السلندر وكذلك الاسطوانه تحياتي
Thanks i will do that, stay tuned it might take a while but I will get it done.
Got a tip from a clutch specialist.... If the clearance between the pressure forks and the release bearing is too big you must add shims or a washer on each bolt between pressure plate and flywheel, otherwise you will find hard to get gears.... This especially happen when you resurfaced (skimmed) the pressure plate
I once did that and it worked, thanks very much for the knowledge.
This guy is not make sure. You can't come out to help us and you not sure
Sorry I couldn't help you
He can't teach us to tune a cab while he don't know the idling jet
😴😴
Lol easy
The car looks nice, although the paint on it is gone
The owner is going to paint it, stay tuned
Thanks everyone who watched these video/clip let me know if you wanna see more of these car. I don't own the car, it's a friend's car
Hello hope your good I wanted to ask how much did the bearings cost and where dd you buy them Thanks
It's been 3 years since I bought,but I think around R600 if I'm not mistaken most spare shops should have them. I will check and come back to you
I have a 1962 model still running if you interested
Where are you located
@@MOGODDTHEFIXER Pretoria
@@ezzelindeerling1518, please inbox me oh tit tok @Mogoddthefixer. Thanks
It's still a re-buildable car it only dirty give it your time and boom you got a nice car Ford Cortina GLs 3.0 Work on the miner problems take out the seat and clean them properly..well done
Thanks for the motivation, I will surely do that
Hi brother could i get your contact details or FB messenger i desperately need help with my 1.6 carb....
Hi, I'm having problems with my number, what's seems to be the problem
@MOGODDTHEFIXER it's boging down when i accelerate and it idles high i. The morning its refuses to stay it's always cutting off
it's a real death capsule
What you mean lol
My dad had one of those.
It's a nice car to drive, your father has good taste
Lui redonner une beauté a la Renault 16 ça sera génial c'était une voiture avec des qualités exceptionnelles c'est comme une vieille femme bien maquillé ça change tout
Merci, restez a l'ecoute
Quel malheur de voir une Renault 16 dans l'état la Une voiture exceptionnel ❤❤
Je ferai de mon mieux pour lui redonner son ancienne gloire.
Thank you from Greece, it was very helpful the whole video, I own a t2 1972 and I have a problem with squizing noise while I am driving, very detailed description you did thank you again
Glad I could help, stay tuned
Nice bus,love the gear shift extension lol
Thanks is easier for me to shift
Hey buddy
Hey
Bro u dont know what u talking about
It works for me so it should work for you
Hello I think you didn't go much further with some other components like jets,two pieces that seats under those jets and the float needle..thank you sir
Thanks for the lovely knowledge
I kou don't know English but i 😅 understand everything you said bro ...very great video but i can't use this method because I don't want to remove the flywheel.... but 👍🏿
Thankyou very much sir
You welcome
Do you drive it often
Yeah I do
Like the way it sound
Thanks
I have never seen a Renault ts automatic
Nice car indeed
Nice car you should restore it
I will like to see it run please
Sorry but I sold it to my friend
Thanks boss I have checked on my carburetor and only to find out that my choke cable was loose and agdusted abit. Also from your video
Glad I could help
Very nice video, I have a question; My golf 1 is starting, but then dies again it only needs a rev to keep on. Would you say it's bad timing? I have checked my fuel pump but couldn't see any damage.
Check out my video on why your car is not idling
Man I must admit you didn't do your homework
How to set a Hi cle
Check out my video on how to tune your golf carburetor
Nice video. What is the fuel pressure of the pump
Thanks, it's about 4 psi.
@@MOGODDTHEFIXER Many Thanks!!!
Idling jet
Whats causing petrol not to pass through the small hole when i accelerate
I have 2l golf engen after timing maks it cranks but never starts but it has some shoots on the exoust
Same
could your timing be out by 180 degrees
It helped. They all haters
Mine does the same
Hi,present that,video,if possible
Stay tuned I will do that, thanks for watching
I got a problem with mine like this it don't have spark not showing desh bored lights what can the problem be
What happened
With?
Solución?
@@oscararredondo4523, it was the distributor, I changed it to pointless one
Phu rrrrrrr. What's that
Lol
Hey Bru u trying but u r confusing me a lot. Sorry. Do more work.
Xo
Hi there,apart from the original I bought a new one but it's having extra inlets and outlets pips on it.
Stay tuned I will, explain more about it
Thanks that's help me lots
That means the problem is not that cap holding the diafraim?
Hi what couse the accelerator pumps to link the petrol and how to fix it?
Stay tuned I will show you how
Ok