Пікірлер

• 
  @justindrawbaugh89275 күн бұрын

  Well made!!

• 
  @farashvac8 күн бұрын

  Thanks for the videos bro , cheers .

• 
  @gregfox78512 күн бұрын

  AWESOME, THX!

• 
  @habibmm-nx4ms17 күн бұрын

  Thanks for your tips 🙏

• 
  @RepublicanJonCardiasmenos18 күн бұрын

  I want to buy the the SC680 Fieldpiece Multimeter but there are a lot of videos describing phantom amp readings when the wireless button is pressed. Would you still recommend I get this meter? I don’t mind the size. Size matters, lol!!!

• 
  @La2venida22 күн бұрын

  If you make repairs after pumping down the system. Can pressurize it with n2 with it isolated? Or would I only be able to evacuate and then open the valves

• 
  @edwardtsang324328 күн бұрын

  I used to have the Howe ice flake in 2010 it was a very reliable machine. You can buy the Chinese ice flakes for one quarter the price and they work even better and are reliable and basic like the Howe.

• 
  @jamesmooney534829 күн бұрын

  That is a thread on unit. To change out the braze in's, do you have to evacuate the system? Or can you just swap the cap lines attached to the bottom of the switch

• 
  @Cscrefandhvac23 күн бұрын

  You have to evacuate and use the new cap tubes that are on the new switch .

• 
  @Cscrefandhvac23 күн бұрын

  Also some switches have threaded connections but these particular ones in the video do not

• 
  @jamesmooney534823 күн бұрын

  @Cscrefandhvac Thanks, I appreciateit! I was able to adjust the unit and is now working properly If it fails completely, I'll probably use the "peanut" screw on type Lo pressuse cut-out control switch mounted of a brass T Thanks again

• 
  @mariogonzalez655829 күн бұрын

  Just fixed a freezer today thanks to your video. Plus a you got a new subscriber!

• 
  @Cscrefandhvac23 күн бұрын

  Thanks man I appreciate that and glad the video could help 👍

• 
  @jjsifo1Ай бұрын

  I own an mp2x then realized theMP1 was more convenient so found one on ebay ,great little bag.

• 
  @thatdeal395Ай бұрын

  I can't find a thermostat like that any help

• 
  @Cscrefandhvac23 күн бұрын

  It’s a Whites - Roger’s tsat. Model 1609-101

• 
  @pressleymiller5443Ай бұрын

  I have installed one of these 3s. I never get a green light and won’t cut off the compressor. Module has power and sensor ohms good. What do you think?

• 
  @Cscrefandhvac23 күн бұрын

  Are the correct wires on the L and the M

• 
  @dioncurtiscurtis3188Ай бұрын

  Those green compressors… what kind are those? And did any of those bad boys run off CO2?

• 
  @pbservano2 ай бұрын

  Thanks fir sharing....subscribed.

• 
  @pnp88492 ай бұрын

  Got into commercial refrig not too long and now about to take refrigeration state exam for contractor. I read from forum it's best to pinch it because sometime it leaks. Thanks for the videos.

• 
  @Cscrefandhvac23 күн бұрын

  They very rarely leak and if they did you’d see it leaking right when it was cut. Pinching it wouldn’t hold back the pressure anyway especially since it’s in the high side of the system

• 
  @maheradous92572 ай бұрын

  Good job. Please share to me the news videos. Thanks

• 
  @nakiapringley53912 ай бұрын

  Great video bro

• 
  @ljmanz552 ай бұрын

  That's not a rack it's a unit huge difference

• 
  @CscrefandhvacАй бұрын

  Yes. Where are you getting a rack from ? I never mentioned a rack

• 
  @triggerwarning24392 ай бұрын

  Can anyone translate to west coast? 😂👍

• 
  @CscrefandhvacАй бұрын

  🤣

• 
  @cjlosangeles60452 ай бұрын

  thank you I just installed one of these and I had the same issue. I couldn’t figure out the leak. You saved me 🙏😩

• 
  @kingsolo62412 ай бұрын

  The main reason you want the scroll to stop pumping down around 15psi is to not send too much liquid through the scroll at the top of the compressor. It’ll damage and ruin the scroll compressor.

• 
  @garretlizotte62882 ай бұрын

  How many of those valves work?! XD

• 
  @mikemalone61033 ай бұрын

  Does that valve modulate or is it on/off? I don’t believe I have seen a headmaster maintain a head pressure (180) at the theory goes of what it’s supposed to do, even on a new install… what is the range accuracy (+/-) ? The one I did replace once, was plugged with dirt in the strainer. Under the seat I found a chip of something holding it open. I inquired about replacing the 3/8” strainers in the entry ports because Sporlan doesnt include them in the replacement valve, go figure,… Simons has none in inventory, and said they need a minimum order of like a box of 500 to order them or some ridiculous thing like that. They weren’t about to order them. I ended up installing a fan cycle control on one of the two fans…

• 
  @Cscrefandhvac23 күн бұрын

  They modulate open and closed depending what the pressure is and then they hold at 180 or so. What was the outside temp where it wasn’t holding 180 ? Of it was warm or hot out the head pressure will run like it normally does. These are for the cold weather so it will maintain a pressure of 180 because if it goes too low when cold out the system won’t cool properly

• 
  @Jonpestillo3 ай бұрын

  Really good stuff! thank you so much not many good teachers anymore.

• 
  @timothybostic81513 ай бұрын

  I love my Phoenix meters wouldn’t trade them for the world

• 
  @ALEMAlem-kl7mp4 ай бұрын

  Veri good

• 
  @Bennie7164 ай бұрын

  Basically a hot gas bypass valve 🤔

• 
  @Cscrefandhvac23 күн бұрын

  Pretty much works the same way , yes

• 
  @rocker86924 ай бұрын

  Seems simple enough

• 
  @glendekoker36824 ай бұрын

  Got a single unit started kicking on and off. I adjusted for longer time but next day doing again? Do they go bad or do you think gas low? Fridge is cold.

• 
  @Cscrefandhvac23 күн бұрын

  What kind of system and compressor is it ?

• 
  @glendekoker368221 күн бұрын

  @@Cscrefandhvac found leak

• 
  @Floridaman2254 ай бұрын

  Just replaced one of these for the first time . Very good info man

• 
  @TonyHoanz-vc2pq4 ай бұрын

  Thanks for sharing 😊

• 
  @tylerducomb41204 ай бұрын

  I’m working on a heat craft evaporator that does not currently have a defrost termination fan delay. Should I be looking for a jumper between N&F to remove in order to install a defrost termination fan delay?

• 
  @ClearviewTrading4 ай бұрын

  im in queens are you looking for an apprentice

• 
  @tonyp60885 ай бұрын

  Good driver cam angle. 🍻

• 
  @jhatfield27555 ай бұрын

  Realistic van thats not all Milwaukee and tools that arent needed. Full of parts

• 
  @jasontaylor98715 ай бұрын

  This question is 5 years after the video but do you trust the gauge on the pump as your only micron gauge?

• 
  @Cscrefandhvac5 ай бұрын

  Yes I do but I also like to use another one on the system also

• 
  @nooragha19875 ай бұрын

  HI bro can make a video about how to pump down the cooler

• 
  @ronaldgcuma75885 ай бұрын

  You also holding a defrost heater on your fingers😂

• 
  @tonyp60885 ай бұрын

  Thanks for the info. I take it there is no way tool adjust differential setting on the high side? Factory set?

• 
  @Cscrefandhvac2 күн бұрын

  On this particular control and most they are factory set. The differential adjustment is used on a condenser fan cycling control always .

• 
  @Bravo_L5 ай бұрын

  Thanks boss, this playlist you made is amazing. 10/10. you won a spot in heaven for sure 😂

• 
  @derekmenke51775 ай бұрын

  I'm working on a turbo air walk-in freezer. At start up, the fans would not run because the fan delay was not cold enough. What will cause that fan delay to get cold enough to kick the fans on if the room is at 65 degrees Fahrenheit. Does the compressor just keep kicking in and out on low pressure till the room gets cold enough?

• 
  @donaldtrumpenstein97225 ай бұрын

  What would happen if the head pressure control failed open?

• 
  @erockscott11845 ай бұрын

  Thats what mine looks like. I replaced it i had a spare new one at home. My unit still has issues though after replacement the fan wont turn on or the compressor. The cap is testing 3.5 MF lower than its rated so ill replace that too and see if they kick on.

• 
  @Skunkhunt_425 ай бұрын

  Thats a big rig!🤠😎🏁

• 
  @bigdaddy49755 ай бұрын

  This is an old reach in cooler it does have a solenoid on it too

• 
  @bigdaddy49755 ай бұрын

  It goes in defrost like normal but I don’t know why I see 120 volts on x no matter what the clock is in

• 
  @bigdaddy49755 ай бұрын

  If you see 120 volts on the x terminal all the time is this normal? It’s running a gravity system coil no fans or heaters I don’t understand how they have this clock wired

• 
  @rebeccaryan49256 ай бұрын

  Your power drill and a car detailing brush kit, or kit on a sander make this super easy!!

• 
  @rebeccaryan49256 ай бұрын

  Can you spray the dust before brushing it off in step 1? To minimize particles being disbursed everywhere?

• 
  @j2duhvis6 ай бұрын

  So if you push in the contractor to pump the rest out you could in theory sweat out any components like solenoid valve without the fear of creating fosgene? Some tech I’ve trained with always cut into the line and let the residual bleed out wherever the solenoid in my example would be. Just curious I could take this knowledge and show the techs something they have over looked.