Is it better to buy 2.5ah batteries in AZ for shorter usage in high temps, or should I avoided ego in the summer?
@John-cj3veКүн бұрын
For the relatively short time that the battery will be in use; the high Arizona temperatures won't bother it. Just be sure to bring the battery back back in the air conditioned house when you are done with your project.
@209chevymon2 күн бұрын
If im changing a fitting that is tapered and needs to seal 3000psi is teflon tape enough?
@crosleyfiver86863 күн бұрын
Clean a "Dirty" bay,, not a clean one
@rgonza93023 күн бұрын
That method of pulling out the o ring and compression ring is specifically not recommended by prevost...thoughts?
@PeteyMcSavage4 күн бұрын
Megs hyper dressing is better and cheaper
@davidmorgan29645 күн бұрын
I’ve been looking at tips for spray guns for washing my cars and beyond the 40* tip there are other numbers (2.0, 2.5, 3.0, 3.5, 4.0, 5.0) what do these mean and how do I know what I need? (Excuse the terminology as I don’t know this. Thanks
@davidmorgan29645 күн бұрын
I’ve been looking at tips for spray guns for washing my cars and beyond the 40* tip there are other numbers (2.0, 2.5, 3.0, 3.5, 4.0, 5.0) what do these mean and how do I know what I need? (Excuse the terminology as I don’t know this. Thanks
@Truchaslayer6 күн бұрын
I’m planning on getting this one soon, however how’s the warranty and does it leak oil like some people have said ?
@shaunnightfire82696 күн бұрын
Not displayed is watts out. The 1p batteries, such as the 2.5ah, can only output around 1100 watts to the motor (assuming 20a output of the 18650s x 56v). This is simply not enough for the mowers or higher end blowers.
@fw14216 күн бұрын
You completely left out how much these batteries cost. The 10 Amp Hour battery costs $500! I can’t imagine how much the 12 AH battery costs. Just for your information,for gods sake,register every Ego mower,battery,charger you buy and staple the receipt to your manual. Ego will fight you to get it replaced under warranty if you don’t!
@John-cj3veКүн бұрын
I haven't had that problem with EGO. They require an image of your receipt sent to them to complete the registration. I just bought the CS2005 chainsaw this month; and the charger that comes with it was heating up batteries. I called EGO and explained the situation; and they are shipping me a replacement charger.
@fw1421Күн бұрын
@@John-cj3ve You have had a different experience than I did. I’m glad they are sending you a replacement without the trouble I did.👍🏻
@Jay-Kaizo7 күн бұрын
Great video! Thank you. I have a question. I didn't pay attention when buying a bunch of accessories for my pressure washer and I have some with 3/8 inch quick connects and some with 1/4 inch quick connects. I didn't even take the stuff out of the boxes yet, but am I going to have to buy adapters to make the 2 sizes work with one another? If that's even possible. Edit: the treads obviously will fit into each accessory that they came with. I'm curious if the male and female connections will be an issue for me
@louisg90589 күн бұрын
Man I guess I’m not keeping up with the jones family because these reels are 2-350 dollars.
@goodkarma49969 күн бұрын
What is the inside diameter of the buckets? I have Montana Original brushes that has a 10” plastic head for the bristles. Just wondering if they’ll fit comfortably inside the buckets
@Danny-xj5ts10 күн бұрын
Kranzle said no quick disconnects.. Can we run quick disconnects
@ramonlima810010 күн бұрын
Great review!
@chriscuthbertson11 күн бұрын
My question is why do car detailing companies sell red or orange nozzle in their sets. a set of two nozzles would be cheaper.
@Greg_P61112 күн бұрын
Can’t believe there’s a company that buys products and sell them 2-3 x retail price that ANYONE can get ANYWHERE. Seriously though I don’t get it! Good for obsessed but as a consumer why would anyone buy here?
@ObsessedGarageShorts5 сағат бұрын
Can you name one product we are marking up 3x over others? Everything we offer is at MAP pricing. You have no idea what you are talking about.
@johnroberts482312 күн бұрын
Don’t you think you should let the fitting grow up and decides it’s own gender 😝
@user-mh4pq3sl8i16 күн бұрын
Mike, thanks for all the great instructions /tips. Quick question - I’m about to invest in Milwaukee Furl impact driver and drill. For this work , do you suggest the M18 or M12. Does the M12 have enough power ? Thanks. Owen from Atlanta
@mastercat3316 күн бұрын
how often would you use a iron remover and when you do use it where in the wash process is it used? Thanks
@InsanelyGhostly17 күн бұрын
Man so many channels have jacked your set up 😂
@dalesuggs365819 күн бұрын
Very informative. Thanks
@progression_decibel20 күн бұрын
Can you omit buffing off the OG tire dressing for a shinier finish or will it sling?
@jrphoto817920 күн бұрын
Will these work with other guns or only the OG spec one? Thanks
@Prickles200120 күн бұрын
Is there any reason not to use an M22 to 1/4" QD on the gun-wand connection (instead of the 3/8")? That way my snow cannon with 1/4" QD can fit on the end of the gun without adaptors?
@goatrosae766524 күн бұрын
Great instructions, bro! You're the best!
@rickraub544824 күн бұрын
Please help me. I bought a mckillans swivel pressure washer gun. It has a 3/8 swivel inlet. My hose is a 1/4 inch so I can’t use my new gun. Is there a 1/4 inch swap out fitting for the mckillians swivel gun? ( also the pressure washer outlet is 1/4 inch otherwise I’d just buy a new 3/8 hose)
@gdude739727 күн бұрын
My 2016 truck was repainted three years ago and the paint is in great shape with no swirls but just a couple of moderate scratches and no dents (knock wood). If I use compound to buff out those scratches, do I need to compound the entire vehicle before polishing and waxing? My challenge is the small time windows provided by Colorado's hot summer weather (with unforecasted light rain bursts in the afternoon), and the fact that my truck doesn't fit in my garage. Would greatly appreciate your advice!
@rickbarg398028 күн бұрын
Love the curve ball
@dougchauvin1858Ай бұрын
I watched this video to learn the measurements of the GHT thread. I want to know the major diameter of the thread and the thread pitch as well as the thread profile. You did not explain any of that. You use improper terms such as O-ring. It’s not an o-ring. It’s a flat ring. Also, you said, tighten up. You should say tighten. There is no up in tightening a fitting. It appears you like swinging your arms when you talk.
@DebtOfLifeАй бұрын
Hi, What pressure washer would you recommend for a 4500 watt champion generator? I have the 2.3 and if trips so often I’m ready to part ways with it for mobile detailing.
@mrchow1500Ай бұрын
I would like to know your opinion on Powerplay pressure washers. They have several product lines such as Mini, Pulse, or Pro. Have you ever tested them?
@jjjjjjjjjjjhjjjjjhjjАй бұрын
So can I use it as a stand alone product ? I’ve used coating about 10 times but don’t like it , makes me nervous if I get a high spot
@heliospena-garcia5714Ай бұрын
so would it be recommended to buy a different cleaner for tinted windows?
@punktpowerАй бұрын
“You know” #256😂
@SnoopFroggNFTАй бұрын
How do you remove a broken quick disconnect from the pressure washer extention pole? Do you put the pole in the table vise to be able to “unscrew” the entire QD to add a new one? Concerned the metal pole will bend when trying to twist off broken pole.
@fosgeАй бұрын
Have you compared this speaker to the Zeppelin AirPlay 240W? Which one sounds better in your opinion?
@fosgeАй бұрын
I wonder how it compares to Zeppelin AirPlay 240W? 
@joorr2444Ай бұрын
So you sell a bunch of parts that don't fit, and the is a rebranded vacuumaid unit that costs double the price....
@daltonschannel8405Ай бұрын
I ordered this hose, and I must say packaging was great with no bendable kinks and shipping was pretty dam fast so I'm very happy with my purchase from OG. Thanks
@chrisracer2007Ай бұрын
Does the European style tap have an adapter to make the opening diameter smaller?
@robertcamaj4477Ай бұрын
I went to Banks Vacuums - they have these exact attachments for much cheaper - the manufacturer of most of these is Wessel Werk... for this reason, I will never buy any products from you seeing that you are willing to price gouge so viscously.
@anthonytran8523Ай бұрын
what kind of spray bottle is that?
@tonykemper8896Ай бұрын
when you expect to have these back in stock?
@michelfortin7055Ай бұрын
My hose has no swivel at either end. Can I still mount it on the reel? I realize that I will have to turn the hose when I screw it in but will it then be a problem to operate the reel?
@neovisual633Ай бұрын
Can you use the OG gun with MTM QD?
@cerwin21Ай бұрын
Looks like the same shade as Dawn
@ObsessedGarageShortsАй бұрын
I agree, but if you put dawn in your washing machine... you would have a bad time.
@cerwin21Ай бұрын
Wife wont let that happen with polish towels and detail rags. I hand wash in a bucket and dry. Getting so busy might need a machine just for rags
@alphasmurf6563Ай бұрын
Matt, has anyone developed a stainless live ball swivel joint fitting? Imagine how sweet that would be to have full rotation not just horizontal. If you develop it can I get a sticker and promo code 😂
@brem02Ай бұрын
Great video! I’m interested in your thoughts on the best electric pressure washer that would be ideal for a six nozzle water broom? I agree flow would be a concern. Our condo building washes the parking garage yearly and our gas pressure unit will be sold. We want to switch to electric to avoid gas fumes and be able to wash with garage door closed. Any ideas?
@neovisual633Ай бұрын
I recently brought a Kobrajet hose and it came with SS fittings, I purchased the Mosmatic T304 QDs and fittings from you guys offer and planned to change it, but the current QDs are so tight and maybe they have put adhesive sealant on it. I am wondering do you have some tips on how to removed those? Or worst case scenario can I use MTM QD with the OG Spec Mosmatic gun I have?
Пікірлер
Is it better to buy 2.5ah batteries in AZ for shorter usage in high temps, or should I avoided ego in the summer?
For the relatively short time that the battery will be in use; the high Arizona temperatures won't bother it. Just be sure to bring the battery back back in the air conditioned house when you are done with your project.
If im changing a fitting that is tapered and needs to seal 3000psi is teflon tape enough?
Clean a "Dirty" bay,, not a clean one
That method of pulling out the o ring and compression ring is specifically not recommended by prevost...thoughts?
Megs hyper dressing is better and cheaper
I’ve been looking at tips for spray guns for washing my cars and beyond the 40* tip there are other numbers (2.0, 2.5, 3.0, 3.5, 4.0, 5.0) what do these mean and how do I know what I need? (Excuse the terminology as I don’t know this. Thanks
I’ve been looking at tips for spray guns for washing my cars and beyond the 40* tip there are other numbers (2.0, 2.5, 3.0, 3.5, 4.0, 5.0) what do these mean and how do I know what I need? (Excuse the terminology as I don’t know this. Thanks
I’m planning on getting this one soon, however how’s the warranty and does it leak oil like some people have said ?
Not displayed is watts out. The 1p batteries, such as the 2.5ah, can only output around 1100 watts to the motor (assuming 20a output of the 18650s x 56v). This is simply not enough for the mowers or higher end blowers.
You completely left out how much these batteries cost. The 10 Amp Hour battery costs $500! I can’t imagine how much the 12 AH battery costs. Just for your information,for gods sake,register every Ego mower,battery,charger you buy and staple the receipt to your manual. Ego will fight you to get it replaced under warranty if you don’t!
I haven't had that problem with EGO. They require an image of your receipt sent to them to complete the registration. I just bought the CS2005 chainsaw this month; and the charger that comes with it was heating up batteries. I called EGO and explained the situation; and they are shipping me a replacement charger.
@@John-cj3ve You have had a different experience than I did. I’m glad they are sending you a replacement without the trouble I did.👍🏻
Great video! Thank you. I have a question. I didn't pay attention when buying a bunch of accessories for my pressure washer and I have some with 3/8 inch quick connects and some with 1/4 inch quick connects. I didn't even take the stuff out of the boxes yet, but am I going to have to buy adapters to make the 2 sizes work with one another? If that's even possible. Edit: the treads obviously will fit into each accessory that they came with. I'm curious if the male and female connections will be an issue for me
Man I guess I’m not keeping up with the jones family because these reels are 2-350 dollars.
What is the inside diameter of the buckets? I have Montana Original brushes that has a 10” plastic head for the bristles. Just wondering if they’ll fit comfortably inside the buckets
Kranzle said no quick disconnects.. Can we run quick disconnects
Great review!
My question is why do car detailing companies sell red or orange nozzle in their sets. a set of two nozzles would be cheaper.
Can’t believe there’s a company that buys products and sell them 2-3 x retail price that ANYONE can get ANYWHERE. Seriously though I don’t get it! Good for obsessed but as a consumer why would anyone buy here?
Can you name one product we are marking up 3x over others? Everything we offer is at MAP pricing. You have no idea what you are talking about.
Don’t you think you should let the fitting grow up and decides it’s own gender 😝
Mike, thanks for all the great instructions /tips. Quick question - I’m about to invest in Milwaukee Furl impact driver and drill. For this work , do you suggest the M18 or M12. Does the M12 have enough power ? Thanks. Owen from Atlanta
how often would you use a iron remover and when you do use it where in the wash process is it used? Thanks
Man so many channels have jacked your set up 😂
Very informative. Thanks
Can you omit buffing off the OG tire dressing for a shinier finish or will it sling?
Will these work with other guns or only the OG spec one? Thanks
Is there any reason not to use an M22 to 1/4" QD on the gun-wand connection (instead of the 3/8")? That way my snow cannon with 1/4" QD can fit on the end of the gun without adaptors?
Great instructions, bro! You're the best!
Please help me. I bought a mckillans swivel pressure washer gun. It has a 3/8 swivel inlet. My hose is a 1/4 inch so I can’t use my new gun. Is there a 1/4 inch swap out fitting for the mckillians swivel gun? ( also the pressure washer outlet is 1/4 inch otherwise I’d just buy a new 3/8 hose)
My 2016 truck was repainted three years ago and the paint is in great shape with no swirls but just a couple of moderate scratches and no dents (knock wood). If I use compound to buff out those scratches, do I need to compound the entire vehicle before polishing and waxing? My challenge is the small time windows provided by Colorado's hot summer weather (with unforecasted light rain bursts in the afternoon), and the fact that my truck doesn't fit in my garage. Would greatly appreciate your advice!
Love the curve ball
I watched this video to learn the measurements of the GHT thread. I want to know the major diameter of the thread and the thread pitch as well as the thread profile. You did not explain any of that. You use improper terms such as O-ring. It’s not an o-ring. It’s a flat ring. Also, you said, tighten up. You should say tighten. There is no up in tightening a fitting. It appears you like swinging your arms when you talk.
Hi, What pressure washer would you recommend for a 4500 watt champion generator? I have the 2.3 and if trips so often I’m ready to part ways with it for mobile detailing.
I would like to know your opinion on Powerplay pressure washers. They have several product lines such as Mini, Pulse, or Pro. Have you ever tested them?
So can I use it as a stand alone product ? I’ve used coating about 10 times but don’t like it , makes me nervous if I get a high spot
so would it be recommended to buy a different cleaner for tinted windows?
“You know” #256😂
How do you remove a broken quick disconnect from the pressure washer extention pole? Do you put the pole in the table vise to be able to “unscrew” the entire QD to add a new one? Concerned the metal pole will bend when trying to twist off broken pole.
Have you compared this speaker to the Zeppelin AirPlay 240W? Which one sounds better in your opinion?
I wonder how it compares to Zeppelin AirPlay 240W? 
So you sell a bunch of parts that don't fit, and the is a rebranded vacuumaid unit that costs double the price....
I ordered this hose, and I must say packaging was great with no bendable kinks and shipping was pretty dam fast so I'm very happy with my purchase from OG. Thanks
Does the European style tap have an adapter to make the opening diameter smaller?
I went to Banks Vacuums - they have these exact attachments for much cheaper - the manufacturer of most of these is Wessel Werk... for this reason, I will never buy any products from you seeing that you are willing to price gouge so viscously.
what kind of spray bottle is that?
when you expect to have these back in stock?
My hose has no swivel at either end. Can I still mount it on the reel? I realize that I will have to turn the hose when I screw it in but will it then be a problem to operate the reel?
Can you use the OG gun with MTM QD?
Looks like the same shade as Dawn
I agree, but if you put dawn in your washing machine... you would have a bad time.
Wife wont let that happen with polish towels and detail rags. I hand wash in a bucket and dry. Getting so busy might need a machine just for rags
Matt, has anyone developed a stainless live ball swivel joint fitting? Imagine how sweet that would be to have full rotation not just horizontal. If you develop it can I get a sticker and promo code 😂
Great video! I’m interested in your thoughts on the best electric pressure washer that would be ideal for a six nozzle water broom? I agree flow would be a concern. Our condo building washes the parking garage yearly and our gas pressure unit will be sold. We want to switch to electric to avoid gas fumes and be able to wash with garage door closed. Any ideas?
I recently brought a Kobrajet hose and it came with SS fittings, I purchased the Mosmatic T304 QDs and fittings from you guys offer and planned to change it, but the current QDs are so tight and maybe they have put adhesive sealant on it. I am wondering do you have some tips on how to removed those? Or worst case scenario can I use MTM QD with the OG Spec Mosmatic gun I have?