Didn’t know that bearing removal tool existed… thanks for the video
@preacher0311638 ай бұрын
Dude,stop rambling
@TRAXRIPPER10 ай бұрын
Push this up so the little flimsy things wont be so flimsy! Lmfao! And thats exactly how it works and should be how its explained in the manual! That was GOLD!
@z0sickvett60 Жыл бұрын
Thanks for the awesome vid
@ramirocsanchez3612 Жыл бұрын
this is a good video. thanks.
@nestorcaamano307 Жыл бұрын
Thanks for the help
@ThomasBilt Жыл бұрын
Bet thanks brother
@dangerdavefreestyle Жыл бұрын
Great tool you got there! Eliminates the need to take it all apart. Yank out the old and press in the new!
@Mattys91gt Жыл бұрын
I had the wrong one from 2 different part stores but Amazon had the right one or will see tomorrow
@beerggls2 жыл бұрын
Yoke.. yolk.. same difference
@pc-wd9qc2 жыл бұрын
Your a lifesaver
@scottmoot29692 жыл бұрын
When I did mine, I had trouble fitting the yoke back in. T5 tailshaft bushings are align honed at the factory. There's a few. 001"s of crush as the bushing is pressed in. After 3 bushings, I had to remove the aluminum tail housing and use a brake hone to get the yoke to fit. Mine was a pain, I've heard that most aren't. I've done this in other trans and never had any problems.
@racerx53792 жыл бұрын
Good job alex , thank you !!
@rickgarza452 жыл бұрын
What's the tool brotha. An what's the seal part number thanks
@josevega12042 жыл бұрын
Spañol bro ???
@djcostin2 жыл бұрын
Good video bro, I did a RMS and oil pan gasket on my Fox and this is next! I didn't realize it was so simple. Thanks!
@joegarcia92212 жыл бұрын
Hahaha
@MrRoy-rb1je3 жыл бұрын
Outstanding!
@samatwood43503 жыл бұрын
1) on a real note, where did you get the bushing 2) where did you get the tool?
@SilverBullet93GT3 жыл бұрын
Going to the store to buy some eggs, i need to replace the yolk in my car
@carlcampbell68273 жыл бұрын
That is a pretty good tip. Replace rubber seal and if it continues to leak then the metal bushing is bad.
@justinnixon99143 жыл бұрын
Hey bro you got the same wheels as my 88’ Thanks for the help, much appreciated
@corridonsa3 жыл бұрын
I need that tool that you borrowed that slips up inside and pulls out the bushing what is it called so I can look it up I need one
@viper69603 жыл бұрын
Where did you get the bushing from? I am having trouble finding one.
@suavemb10013 жыл бұрын
Very helpful thanks
@GreatValueJohnnySins3 жыл бұрын
Yo thank you so much amigo!
@MrSandhu114 жыл бұрын
Sick ass foo
@joebrennan4454 жыл бұрын
Thanks for making this video! It really helped me to understand better what I need to do.
@donmckenzie43294 жыл бұрын
Thanks man. Super helpful.
@aaroncarroll72184 жыл бұрын
Where do I get that tool
@300whiteout94 жыл бұрын
Thanks bro
@yeudsiegal52854 жыл бұрын
Thank you very much for your maintenance video. It was very explanatory and you seemed to make sure we understood by repeating points.
@yeudsiegal52854 жыл бұрын
Are you not supposed to grease the teeth on the output shaft?
@irate745 жыл бұрын
Where can we buy that tool?
@btchhopperou8125 жыл бұрын
GREAT help! Very informative video- Well put in layman's terms as well! Certainly a big help to those that are new to working on their own projects AND those with experience just wanting to know exactly what to expect when attempting this for the first time. BTW- Fuck the asshat that gave you a thumbs down for it being a 'skinny' vid... petty people suck! Keep up the good work!
@InternetDude6 жыл бұрын
Really helpful video, too bad I had to give it a thumbs down because vertical video.
@foreigner2thisworld6 жыл бұрын
Alex - Nice job on the video. Very helpful as I am replacing the clutch on my '87 GT and while it is all apart will do the maintenance you outlined in your video. Thanks for taking the time to make and post this video.
@MorbidThrasher6666 жыл бұрын
I have to do this very soon,i have the pieces but looks like ima order a new yoke now and my seal doesnt have the plastic on it so ill get another one.
Пікірлер
Didn’t know that bearing removal tool existed… thanks for the video
Dude,stop rambling
Push this up so the little flimsy things wont be so flimsy! Lmfao! And thats exactly how it works and should be how its explained in the manual! That was GOLD!
Thanks for the awesome vid
this is a good video. thanks.
Thanks for the help
Bet thanks brother
Great tool you got there! Eliminates the need to take it all apart. Yank out the old and press in the new!
I had the wrong one from 2 different part stores but Amazon had the right one or will see tomorrow
Yoke.. yolk.. same difference
Your a lifesaver
When I did mine, I had trouble fitting the yoke back in. T5 tailshaft bushings are align honed at the factory. There's a few. 001"s of crush as the bushing is pressed in. After 3 bushings, I had to remove the aluminum tail housing and use a brake hone to get the yoke to fit. Mine was a pain, I've heard that most aren't. I've done this in other trans and never had any problems.
Good job alex , thank you !!
What's the tool brotha. An what's the seal part number thanks
Spañol bro ???
Good video bro, I did a RMS and oil pan gasket on my Fox and this is next! I didn't realize it was so simple. Thanks!
Hahaha
Outstanding!
1) on a real note, where did you get the bushing 2) where did you get the tool?
Going to the store to buy some eggs, i need to replace the yolk in my car
That is a pretty good tip. Replace rubber seal and if it continues to leak then the metal bushing is bad.
Hey bro you got the same wheels as my 88’ Thanks for the help, much appreciated
I need that tool that you borrowed that slips up inside and pulls out the bushing what is it called so I can look it up I need one
Where did you get the bushing from? I am having trouble finding one.
Very helpful thanks
Yo thank you so much amigo!
Sick ass foo
Thanks for making this video! It really helped me to understand better what I need to do.
Thanks man. Super helpful.
Where do I get that tool
Thanks bro
Thank you very much for your maintenance video. It was very explanatory and you seemed to make sure we understood by repeating points.
Are you not supposed to grease the teeth on the output shaft?
Where can we buy that tool?
GREAT help! Very informative video- Well put in layman's terms as well! Certainly a big help to those that are new to working on their own projects AND those with experience just wanting to know exactly what to expect when attempting this for the first time. BTW- Fuck the asshat that gave you a thumbs down for it being a 'skinny' vid... petty people suck! Keep up the good work!
Really helpful video, too bad I had to give it a thumbs down because vertical video.
Alex - Nice job on the video. Very helpful as I am replacing the clutch on my '87 GT and while it is all apart will do the maintenance you outlined in your video. Thanks for taking the time to make and post this video.
I have to do this very soon,i have the pieces but looks like ima order a new yoke now and my seal doesnt have the plastic on it so ill get another one.
Where you get your bushing
Thanks for the help bro!!👍👍👊👊