This channel is here to share fishing and boating knowledge. We fish out of Raritan Bay NJ and frequent the wrecks and reefs off the coast of Monmouth County. I also do my own boat and engine maintenance. At times you will see videos that will show you how to perform some of these tasks.
Пікірлер
Another excellent video! Watched this tutorial and realized I didn’t have an o-ring! Ordered what I needed and got this simple job done. If I hadn’t watched your vid the old o-ring would have went back in! Thank you so much for the great detail in your videos.
You are very welcome!!
Thank you for an awesome video! Just completed timing belt and t-stats on my VF250LA. Your video gave me the confidence to diy! Thank you sir!
@@TnFlyinGrizzlyExcellent!!! Its not that hard if you take your time and have the right tools. Thank you for the kind comments.
Somebody please tell me why you cannot simply just wire brush those anodes and put them back in. They show almost zero wear, only sea water crud. YAM wants stupid money for an anode. Made of quite possibly the shittiest metal on earth. Were they a buck or two a piece? SURE, toss em.
@@lbowsk I probably could have. I did that project sooner than it needed to be done.
Excellent video! Was even easier todo than shown. Just had my starboard 2023 F300 with only 260hrs shutdown and refuse to restart. Figured it was the fuel filter, watched your vid, changed it in literally less than 5 minutes and we're back up and running. Thanks
@@KieranCox thank you. There's more F300 videos on the channel. Please subscribe!
What makes filter fill up and leak down half way..fill up and back down. Every 30 secs it fill to top and back down
Your low speed pump aka take up pump fills the filter and your VST tank. Your high speed pump sends it to the motor from the VST.
Great video, where did you find the snaps with the 8/32 ss screw (bolt). Can't find it anywhere, thanks for any info you can give. Giles
Thank you. I bought them here: www.sailrite.com/Snap-Fastener-Machine-Screw-3-8-8-32-Nickel-Plated-Key-H
@@4RibsFishing Thanks so much for the quick response, have ordered.
Well done! 🤩💯
@@arizadam12 thank you!!
Got a Cobia as well. Same pump went out after 2 years. I’m doing this!
Check out my video on the macerator pumps!!
F me, the 2 strokes are a dream to service compared to these 4 strokes.
Awesome thank you
You are very welcome!
Love pursuits but the OOS models
Is it my eyes, or does the knife need sharpening?
Probably!!!
Does this affect the 360 view on the camera display? Do you still get the side view cameras as well? Curious to know what camera views this affects by relocating. Thank you.
This camera only replaces the rear view mirror view. No other cameras or views are impacted.
We have a Denali so I don’t know if it is any different with the cameras. Someone said it would affect the 360 camera view because that pulls from multiples cameras and moving this rear view mirror view camera could affect that.
question, at how many hours is this service done
My shop manual doesnt say - but I flush every trip and it was packed in there. Id say 500hrs.
excellent no music no bullshit just the facts , perfect
Well done! I’m installing a new raw water wash down system and appreciate the reverse freshwater rinse add-on.
They just don't last long with salt water running through them.
Looks like he changed out perfectly good anodes…..hardly consumed at all. If you flush your engine after use, I would not recommend this anode replacement…vastly far higher probability of engine damage and oil leaks. If your boat sits un flushed in salt water….different story.
They were in good shape. With how I flush I can easily stretch the interval to 750 hours.
WHERE would a SK 2 go?
They put them under the helm seats. But you lose the drawers.
Great idea and video, I am using your idea. Thank You!
Glad it was helpful!
thanks for helpful video , i did not know there is another filter inside the tank got to change it just over 1000 hrs
Glad it helped
Does your aluminium roller spin with the plastic sleeve or just the plastic?
When I 'roll' a ladder up there they both spin. With no weight I can spin the sleeve by itself.
How heavy of a sinker are you using? I see party boats using 8-12oz.
Today I was spot locking with 4oz. Needed 8 to drift.
Great video I’m assuming the same tailpipe would fit for a 2024 2500 HD Chevy midnight edition gas burner also I’m assuming it did not mess with any of the O2 sensors by any chance did it improve the gas mileage due to the no restrictions that the factory exhaust has could you put a link in the description for that exhaust?
It's the same for the Chev 2500. It has no performance or mileage impact, just the sound. Also no impact to sensors. www.gmpartswarehouse.com/oem-parts/gm-6-6l-gas-cat-back-exhaust-upgrade-system-with-19420408
Starter plus og minus sikring kaput spørgsmål om hvor for sikring kaput
Your fuse box will be on the starboard side of the engine, towards the top front part of the motor.
Doesn't RPM factor in to water pressure? What's the port vs. the star engine RPM?
yes of course - all tests were done at idle 600rpms. While my test could have been conducted more scientifically, there is clearly a difference between the two pumps.
Is this the first time doing this? What's the service interval for these filters?
That was the first time. I always flush, I'm thinking salt water, no more than 800hrs.
Everglades with the highest deadrise for rough weather in the industry 25 degree
Whole baked ling is incredible.
It's such a delicate flesh. Good idea to cook it whole!
Does the mount wobble or have free play in heavy seas? I am debating whether to use the shuttle slide, or just mount the motor directly onto the deck.
The only reason to use this mount is if you need to slide the motor further out on the rub rail. If you don't have that issue, just go direct to the deck. BTW, these motors don't work in heavy seas.
How long should it take a seasoned machanic to replace Internal Anodes on a Yamaha 4.2, 200hp V-Max Sho. Year is 2021. 500 hour service.
I'm bet they charge 1.5 hrs.
Thank you for sharing! I found the sound underwhelming and will stick with Corsa....
Glad I could help
Did your kit allow your mirror to display rearview when in drive
Yes. This kit just relocated the factory camera. The mirror always and only acts as a rear view mirror.
Howdy sir. I am strongly considering this system. Are you happy with it in all aspects? If you had the ability to build something similar your self (which you may), is there anything you would change about the design? Is this system full extension? For the price, it is toeing the build vs. buy line for me. I'm interest in your feedback. Thank you in advance.
I absolutely love the 4000lb model I have. If I built it myself, I'd try to cut some height out. You lose approximately 5" with this model. It's 75% extension-which turns out is more than enough. 100% sounds good, but I don't think it's necessary to reach everything. I'm only 5'11".
@@4RibsFishing thank you again for the feedback.
Awesome video! If I’m just doing the check valve and filter on the top of the vst, do I need to remove the whole tank? Jumping on that this morning.
It may be hard to reach the screws around the top with it on. Check that first before removing.
great idea ! a stainless spring clip might also work
Yes it would!
ماشاءالله
Thank you!
I'm just a little shocked that Yamaha couldn't design a simpler approach to replace these anodes. I can't believe they couldn't come up with a better design than putting anodes under the valve cover. I'm guessing they bank on most people not replacing these and motors lasting much shorter than a "smarter" design. Thank you so much for this very detailed video on how to DIY. I guess I will have to go look to see how often this replacement has to take place. I only have a bit over 100 hours at the moment and am in salt water about 10% of the time.
Thank you Paul. I have a bunch of videos on the 4.2l. Please give them a look too!!
You have nothing to worry about. Those anodes are huge. He changed them when they had over 95% of their life left. OCD or just trying to make a helpful video. I think he was just trying to make a helpful video.
Very helpfull
Thank you, I try.
Is this the GM Borla accessory exhaust or S-type for the 6.6L gas? Thank you.
It's the GM Borla accessory
Excellent. Just ordered that for my 24 Sierra HD. Wanted to hear it, ty!!
@@4RibsFishing I just got it put on my truck today. Perfect, not loud inside at all. Used to the S type or Atak and they are just loud all the time. Great sound when you get on it.
Very detailed video, thank you for sharing this.
You are welcome!
Hey there… wanted to see how this fix is holding up? Great permanent fix for snaps! Worth the < $100 investment
Still holding! I'm very happy with the results.
What about the bed camera? Have a link for that camera to see the stuff in the bed? I did the same thing for rear view mirror but that same camera doesn’t work for bed camera or cargo camera
I've asked them about the bed cam. They said they will work on it- but they need other people to call and show there is demand.
@@4RibsFishing I wonder if their 360 camera they sell will work for it now as it looks to be the same kind of camera but its more expensive than this camera
Huge thanks. Time to order my cap now knowing there is a good solution.
I'm very happy with the camera.
Have one for the F200XB or is it the same? Great video...good job11
I recorded the 200 last week. Just need to edit. Give me a week or two.
Little time crunched. I have the VST out. My question is,is the parts list the same as in this video? Everything looks the same. Thanks again!!
two tips for people following this incredibly helpful video (I just did mine thanks to this video). If you dont have the hose Mike uses, you can use a short pvc pipe over the piston and rest the engine on it to hold the tool. If you dont want to use ATF there is branded Yamaha fluid for the trim tilt system, it is part # ACC-PWRTR-MF-32 and matched what came out of mine (also F300).
Great tips!
Many thanks. You solved my issue.
Excellent! Please consider subscribing.
How has the camera held up? I'm getting a leer cap on my GMC 2500 here very soon.
The screws have a little surface rust, but they already sent me new ones. No complaints on the camera.
@@4RibsFishing still no issue with it at car wash?
My raw water works but don’t have much pressure. It fills the bait well just fine but when you switch it to wash down the pressure stinks
Your raw pump and bait well should be two different pumps. The raw water impeller sounds shot, or the pump motor may be on its last leg.
@@4RibsFishing same bump is for both raw water and live well controlled by a ball valve. Robalo r 200
okay, what pump is that?
It's a sureflo. Check for the link in the description.
Where did you get the literature shown when your explaining the bolt torque pattern on the manifold? Thanks!
I think it was a parts schematic, and I added the notation. Why do you ask?