Пікірлер

• 
  @user001sg9Сағат бұрын

  Very informative video, thanks. I am not sure what exactly is meant by "input" and "output* pairs of field coils. A coil has a beginning and an end terminal. What would here be the "input terminals" and what would the "output terminals" of one single field coil? Could you kindly explain, please? Thanks a lot in advance.

• 
  @danoid79983 сағат бұрын

  I have this exact looking motor on a drill press. When I power it on it hums a little at 0 speed but if I try to increase the speed it shuts my whole press off due to some kind of over temp protection.

• 
  @KevKovac3 сағат бұрын

  Which grit sandpaper do you use? I'm trying to fix my vacuum cleaner motor.

• 
  @firststep775010 сағат бұрын

  So I switched on my vacuum and it began to smoke. I checked the commutator bars with the lowest resistance and in the four of the tests the resistence couldn't settle on a reading: it would spikes and even show "OL". I didn't need to test given the smoking issue but wanted to know where the problem was. Thanks for the this lesson. It was straight to the point.

• 
  @wackyval6898Күн бұрын

  you still cracked the glass around... here is how u do it kzread.info/dash/bejne/o2iJ07GwZK_RlpM.html

• 
  @mehdiadibi7072Күн бұрын

  Fake the glass after sis not the same glass as before.

• 
  @David-rk2cw5 күн бұрын

  If they can make adhesive to keep a crown on your tooth why can't they make one for plastic without having to peg the repair

• 
  @TheLabOtomy4 күн бұрын

  They can, but you need to know the type of plastic to repair to buy the appropriate type of glue for it (plastic is a wide family of products with different properties)

• 
  @marygloupadillo46756 күн бұрын

  What size tubing did you use?

• 
  @TheLabOtomy5 күн бұрын

  Those were 4 mm in diameter

• 
  @LassetUnsSpielen7 күн бұрын

  if you get two of those, pleeease make a bicycle

• 
  @TheLabOtomy7 күн бұрын

  A silent comfy ride for sure!

• 
  @bobbyhutcherson13338 күн бұрын

  those grooves are put there on purpose.

• 
  @TheLabOtomy7 күн бұрын

  Who said they were not?

• 
  @bobbyhutcherson13336 күн бұрын

  @@TheLabOtomy there is no reason to "fix" those grooves. They're machined in by the balancing system.

• 
  @bobbyhutcherson13336 күн бұрын

  @@TheLabOtomy ohh, ok. i misread this comment in the description " I do not know what has caused the grooves on the commutator but they need to be removed for the motor to work properly." I thought maybe you were going to do something to remove them.

• 
  @TheLabOtomy6 күн бұрын

  ​ @bobbyhutcherson1333 Indeed, the vertical grooves (on the stacked lamination) are manufactured for balancing and are per design (not the horizontal grooves on the commutator)

• 
  @LassetUnsSpielen11 күн бұрын

  youtube is totally F'd, I can comment, but i cannot reply or switch accounts. stupid. anyways, the german extension outlets have been a mystery for ages and nobody knows a proper way to open them. you can get a good look if you google images for "mehrfachsteckdosenschrauben"

• 
  @LassetUnsSpielen11 күн бұрын

  gotta be careful with this. if you're unlucky, big brands like disney may be able to sue you for copyright violation

• 
  @LassetUnsSpielen11 күн бұрын

  wait, you didn't play with it? should have applied electricity to see what happens. or at least torch it

• 
  @TheLabOtomy11 күн бұрын

  Good point, probably a missed opportunity

• 
  @LassetUnsSpielen12 күн бұрын

  have you figured out how to remove the screws from extension outlets? i usually just saw through them

• 
  @TheLabOtomy11 күн бұрын

  What do those screws look like in your part of the world? Probably lots of variation between countries/regions

• 
  @gambiarrautil13 күн бұрын

  Hello! My 775 DC motor works and after a while it stops. Could this be dirt in the Commutator? I checked other components and everything seems to be normal.

• 
  @TheLabOtomy12 күн бұрын

  Anything at this stage is subject to suspicion

• 
  @125ordie213 күн бұрын

  entertaining

• 
  @TheLabOtomy13 күн бұрын

  Indeed

• 
  @cathyshiley338813 күн бұрын

  I open carry one of these when I cross a street at an intersection.

• 
  @TheLabOtomy13 күн бұрын

  Absolutely

• 
  @lawtrion667614 күн бұрын

  I love you❤

• 
  @TheLabOtomy13 күн бұрын

  😋

• 
  @blessedthistle970214 күн бұрын

  I had to do this so many times. I would rent a movie and poof, dirty as sin once again. I left the lid on loose for a quickie. All changed as we moved into cd’s and dvd’s. A month into my new CD player and I dropped it mucking around with a new set of speakers. Laser reader wasn’t going to comply, but I spun the worm gear until the laser module reached the end of the rail and made it jump a tooth. Turn on the power and it goes back and plays once again. Countless times with my PS1 because of cats…

• 
  @TheLabOtomy13 күн бұрын

  Good to still see people taking care of their stuff without dumping them at the first hick up

• 
  @malikhalief14 күн бұрын

  Is it possible for me to use a hairdryer to do the 3rd’s step?

• 
  @TheLabOtomy14 күн бұрын

  That will depend of you hairdryer, mine is barely able to make the tubing shrink. An alternative is to hold the whole above (2cm above, i.e. not touching) the flame of a lighter for just half a sec, check and repeat

• 
  @jdsheleg833215 күн бұрын

  USPS uses them, when the moronic customers take the keys with them then it takes forever to have new locks installed, as the diy is impossible due this screws. Thank you for this video!

• 
  @TheLabOtomy14 күн бұрын

  Welcome

• 
  @ayundha.dewi.saristyaasta225315 күн бұрын

  👍👍👍🎉🎉😊

• 
  @TheLabOtomy15 күн бұрын

  🎉🎉🎉

• 
  @fireducky89715 күн бұрын

  iam js tryna clean my ps4 man

• 
  @TheLabOtomy15 күн бұрын

  Ya man

• 
  @Thuyleduygermany17 күн бұрын

  Thanks , ich versuche

• 
  @Nombte1Apellido1-gp2bg17 күн бұрын

  yengo rxactamentr rsr problema... intentate lo mismo... gracias

• 
  @farhadtorkaman655320 күн бұрын

  Perfect 👌👍Thank you 🙏🌹

• 
  @TheLabOtomy19 күн бұрын

  👍🌹

• 
  @townbell224821 күн бұрын

  What type of bit is that? It reminds me of the things used to size rings or wire.

• 
  @TheLabOtomy20 күн бұрын

  One was a hex / Torx bit

• 
  @townbell224821 күн бұрын

  I really like the pen and saw idea. I will have to remember those ones

• 
  @townbell224821 күн бұрын

  I took one apart for a fresnel lens but the lcd doesn’t have them unfortunately. I do have dome light casing that were given to me like the ones in this video that I to use. Thanks for sharing

• 
  @townbell224821 күн бұрын

  Do you know any tricks to get that resin off?

• 
  @TheLabOtomy20 күн бұрын

  Usually acetone does a good job

• 
  @townbell224821 күн бұрын

  What is the wire made of?

• 
  @TheLabOtomy20 күн бұрын

  Copper I think

• 
  @certuv21 күн бұрын

  Just the info I need. Thank you for posting

• 
  @TheLabOtomy20 күн бұрын

  Welcome

• 
  @shortythepresident391322 күн бұрын

  Rubbing compound and permatex orange hand soap (orange bottle with pumice).

• 
  @angelgabrielvasquezchaname81322 күн бұрын

  No hiciste nada ℹ️Ⓜ️bécℹ️l !!!

• 
  @TheLabOtomy22 күн бұрын

  Gracias

• 
  @biscayforex431723 күн бұрын

  Best video I have found on this

• 
  @TheLabOtomy23 күн бұрын

  Great taste!

• 
  @tommyherrera412826 күн бұрын

  I like the third option better than the others.

• 
  @TheLabOtomy25 күн бұрын

  Same here, but not everybody has heat shrink tubing

• 
  @mattyp215526 күн бұрын

  I want to lay my vynal down as flooring how would I go about that

• 
  @TheLabOtomy25 күн бұрын

  Steady / dusty free underground + vinyl layout + protective / levelling coating

• 
  @shawzhang449827 күн бұрын

  would this fix a shorted armature?

• 
  @TheLabOtomy26 күн бұрын

  Nope, it just ensure better contact with the brushes and better energy transfer

• 
  @spartan18728 күн бұрын

  I prefer to do with file and fine tune with sand paper later , don’t need so much mess

• 
  @angelicalord417429 күн бұрын

  Woohoo it worked! I almost had a heart attack when I heard the crack I thought I broke it but works just fine!

• 
  @TheLabOtomy28 күн бұрын

  Nice!

• 
  @Mr.wither_stormАй бұрын

  A lot of the better brands will let you to and swap it for a new one at the store. I did it twice and didn’t need my receipt

• 
  @TheLabOtomyАй бұрын

  Good deal

• 
  @salty_spotted_dogАй бұрын

  What if you had a hundred to do? 😡😂🤣

• 
  @TheLabOtomyАй бұрын

  Method 1 + patience

• 
  @salty_spotted_dogАй бұрын

  @@TheLabOtomy 😂🤣

• 
  @beatgrinderАй бұрын

  it's set to boomer speed; kick it up to 1.5X for normal information processing.

• 
  @TheLabOtomyАй бұрын

  1.5X is the new boomer speed, set it to 2X

• 
  @g.j.dutoit4447Ай бұрын

  Realy hope someone can help me. When i test a armature commutator i set multimeter to 20M ohms then 1 wire on shaft and other wire on commutator, then get reading. Is this mean there is a short between ground and commutator? When set it on lower ohms i not get any reading. Just when set it on 20M ohms and 200M ohms i get reading.

• 
  @manmaru1108Ай бұрын

  Many thanks from Tokyo. I could finally suceeded to simulate human finger touch on the touch panel of my wine cooler(Sakura Works SB103) with GIMDOW SwithX ST1. 2 years ago I once gave up on it, this video gave me a way. You saved my day.

• 
  @TheLabOtomyАй бұрын

  Nice, good to read / hear (and hello Tokyo!)

• 
  @SusanBameАй бұрын

  Wow!! I had housecleaners in today, who have always done a great job, and when they left I noticed not a smudge, but a scratch on my bathroom mirror! I was pretty upset. I just went in and tried the first solution, a bit of toothpaste on a microfiber towel, rubbed for about 20 seconds, and it was gone. I can't see it at all anymore. I am THRILLED. Thank you so much! Just for anyone's information, I used my nanohydroxyapatite toothpaste, originally developed by NASA, as I understand, and the first thing it does in your mouth is heal cracks. I know it's worked in my mouth to heal tiny fractures in my teeth, so I'm not surprised it worked on my mirror.

• 
  @megaman78617 күн бұрын

  Lies...

• 
  @Jeskoishere_broddaАй бұрын

  "honk" for eco horn "TUUUUUUUUUUUUUU" for air horn

• 
  @TheLabOtomyАй бұрын

  TUUUUUUUUUUUUUU

• 
  @pitter-patterАй бұрын

  Does the colour wash away with water?

• 
  @pitter-patterАй бұрын

  Can acrylic colour also be used?

• 
  @TheLabOtomyАй бұрын

  Yes

• 
  @fodeostudioАй бұрын

  Tqvm

• 
  @TheLabOtomyАй бұрын

  Welcome!