Incidentally, the o ring for the cover (end cap) Stoddard part number is SIC 351 999 00 or 901 351 999 00. It doesn't come with the kit.
@timfarmer6483 ай бұрын
I hate seeing people do this use smoke or water. 🤠🤔🖖🤫🏴☠️
@jessehutierez86463 ай бұрын
And booom 🔥 don’t recommend doing this
@gorporpio3 ай бұрын
There's a water hose that's on with a trigger on the hose. And the plug wires aren't junk and the spark plug is in the cylinder head. So no risk.
@manfromks3 ай бұрын
Engine should speed up not die
@gorporpio3 ай бұрын
It can do either.
@formerleo46733 ай бұрын
You can check for vacuum leaks either way…. With NON-FLAMMABLE the idle drops With FLAMMABLE the idle increases Easy Peasy
@joedell713 ай бұрын
Shouldn’t you be using ether or starting fluid for that? Won’t the brakekleen harm seals or gaskets? Asking seriously Ive never seen this done with brake cleaner
@gorporpio3 ай бұрын
It's flammable so wotks. Even WD40 will work. They make a tool specifically for this that uses propane. I have a ttrigger nozzle on a water hose on the floor because a bad spark plug wire can ignite this. I think intake gasket replacement is more of a maintenance thing that something replaced only when leaking or rebuilding the engine.Air leaks burn valves.
@Mr.Westery5 ай бұрын
Hey buddy! How are you? Just shared my new crime documentary video that took 14 hours of hard work. Your thoughts mean a lot to me, so feel free to share your opinions. Can't wait to hear from you, stay healthy!
@Mr.Westery5 ай бұрын
Here's my latest content. This time, we're delving into a real crime documentary. Don't hesitate to share your thoughts; I'm eagerly waiting!
@johnathan81748 ай бұрын
Promo`SM 🙏
@denisament671811 ай бұрын
Also you didn't show welding the bracket back in and what to do about getting the heat off the bracket and not melting the new bushing, i use a water spray bottle after welding each spot weld to stop the heat, also have a wet rag under the rod and around the rod so no slag sticks to the rod. Grat video.
@gorporpio11 ай бұрын
You dont need to weld it on. You use one bolt to hold it up before attempting to install the shifter. The shifter is then installed with one bolt loosely then you can take the other bolt out and use it for the second bolt for the shifter. It's a little tricky but not too bad. By not welding you'll have more adjustment because the retainer isn't stationary. The one I did prior to the one in this video had so little left to right movement in neutral it would favor either 1/2 or 3/4. Adjustment wouldn't do it. I had to put a washer between the lockout plate and the tunnel (or maybe between the lockout plate and the base - can't remember) for each bolt and it was perfect. Adding the washers changed the fulcrum point .
@denisament671811 ай бұрын
You are correct, replacing the bracket and bushing is best because I've seen the original bracket worn and it makes sharp edges on the bracket and it cuts through the new replacement bushing. I've seen them broken so it has to be replaced. More people need to see your video, I've been looking for someone that addressed this issue, THANKS!
@thoughtgrenades11 ай бұрын
nope
@chriskladis9522 Жыл бұрын
That's one out of round tire... definitely road hop.
@gorporpio11 ай бұрын
It made a dull slapping noise. Was concerned it was a loose wheel for a bit.
Пікірлер
Incidentally, the o ring for the cover (end cap) Stoddard part number is SIC 351 999 00 or 901 351 999 00. It doesn't come with the kit.
I hate seeing people do this use smoke or water. 🤠🤔🖖🤫🏴☠️
And booom 🔥 don’t recommend doing this
There's a water hose that's on with a trigger on the hose. And the plug wires aren't junk and the spark plug is in the cylinder head. So no risk.
Engine should speed up not die
It can do either.
You can check for vacuum leaks either way…. With NON-FLAMMABLE the idle drops With FLAMMABLE the idle increases Easy Peasy
Shouldn’t you be using ether or starting fluid for that? Won’t the brakekleen harm seals or gaskets? Asking seriously Ive never seen this done with brake cleaner
It's flammable so wotks. Even WD40 will work. They make a tool specifically for this that uses propane. I have a ttrigger nozzle on a water hose on the floor because a bad spark plug wire can ignite this. I think intake gasket replacement is more of a maintenance thing that something replaced only when leaking or rebuilding the engine.Air leaks burn valves.
Hey buddy! How are you? Just shared my new crime documentary video that took 14 hours of hard work. Your thoughts mean a lot to me, so feel free to share your opinions. Can't wait to hear from you, stay healthy!
Here's my latest content. This time, we're delving into a real crime documentary. Don't hesitate to share your thoughts; I'm eagerly waiting!
Promo`SM 🙏
Also you didn't show welding the bracket back in and what to do about getting the heat off the bracket and not melting the new bushing, i use a water spray bottle after welding each spot weld to stop the heat, also have a wet rag under the rod and around the rod so no slag sticks to the rod. Grat video.
You dont need to weld it on. You use one bolt to hold it up before attempting to install the shifter. The shifter is then installed with one bolt loosely then you can take the other bolt out and use it for the second bolt for the shifter. It's a little tricky but not too bad. By not welding you'll have more adjustment because the retainer isn't stationary. The one I did prior to the one in this video had so little left to right movement in neutral it would favor either 1/2 or 3/4. Adjustment wouldn't do it. I had to put a washer between the lockout plate and the tunnel (or maybe between the lockout plate and the base - can't remember) for each bolt and it was perfect. Adding the washers changed the fulcrum point .
You are correct, replacing the bracket and bushing is best because I've seen the original bracket worn and it makes sharp edges on the bracket and it cuts through the new replacement bushing. I've seen them broken so it has to be replaced. More people need to see your video, I've been looking for someone that addressed this issue, THANKS!
nope
That's one out of round tire... definitely road hop.
It made a dull slapping noise. Was concerned it was a loose wheel for a bit.
We’re gonna get you one day traitor