Пікірлер

• 
  @hirenjariwala660724 күн бұрын

  Can I have sample file of this project?

• 
  @user-cz7nw8uh3o25 күн бұрын

  you should come to algeria to show us how to update size pipes

• 
  @user-cz7nw8uh3oАй бұрын

  I sent you the file to your email address just check in your email address

• 
  @user-cz7nw8uh3oАй бұрын

  hey john did you find the solution ???????????????????????? I told you it doesn't work

• 
  @johnsayre4827Ай бұрын

  I asked last week for the files you are using and supplied an email address. Can you send me your files. I tested it on my end and it works fine.

• 
  @user-cz7nw8uh3oАй бұрын

  how can i send my file? you should give your email

• 
  @johnsayre4827Ай бұрын

  [email protected]

• 
  @user-cz7nw8uh3oАй бұрын

  hey john forget about it anyway it doesn't work

• 
  @johnsayre4827Ай бұрын

  If you would like to send me the your files I can take a look.

• 
  @one-eyejawa3128Ай бұрын

  Really great but I wish the pond outflow had options like Hydraflow extension where you can make adjustments and see in real time the outflow conditions for each storm event

• 
  @user-cz7nw8uh3oАй бұрын

  anyway I follow the same steps but it seems it doesn't work

• 
  @user-cz7nw8uh3oАй бұрын

  hey john let it down I mean I tryed one hundred times but in doesn't work

• 
  @user-cz7nw8uh3oАй бұрын

  I follow the same steps you did, but it seems it doesn't work with my civil 3d 2016

• 
  @user-cz7nw8uh3oАй бұрын

  hey john, I don't manage to update size pipe and yet I follow same steps

• 
  @johnsayre4827Ай бұрын

  Did you go through the setup in the beginning mapping parts from Civil 3D to SSA and back?

• 
  @user-cz7nw8uh3oАй бұрын

  @@johnsayre4827 don't, can you show me how to do that???????????????

• 
  @johnsayre4827Ай бұрын

  @@user-cz7nw8uh3o It is in the first 10 minutes of this video what you need.

• 
  @user-cz7nw8uh3oАй бұрын

  @@johnsayre4827 yeah but I follow the same steps on your video but I don't manage to update size pipes

• 
  @user-cz7nw8uh3oАй бұрын

  Whenever I try to update size pipes all manholes delete automatically on civil 3d 2016

• 
  @user-cz7nw8uh3oАй бұрын

  it doesn't work, when I try to update new size pipe I lose manhole on civil 3d 2016

• 
  @lk17362 ай бұрын

  Thank you for this great video just have the following question concerning the sub base entry why the average was checked instead of the weighted average (area percent ) or one of the of the other options thank you again

• 
  @GracioPermata-wm7xi2 ай бұрын

  I can't make it work to have two orifice. It has that drainage system has no acceptable outfall nodes and outfall xxx has more than 1 inlet.

• 
  @gilbertoflores63244 ай бұрын

  where is Storm and Sanutary Analysis module in version 2024?

• 
  @johnsayre48274 ай бұрын

  If it doesnt install with Civil 3D 2024 you can download the installer for SSA at Manage.autodesk.com and install it.

• 
  @HA-nu9mb7 ай бұрын

  HELLO , I WOULD LIKE TO HAVE THIS TOOLS , HOW CAN I GET IT

• 
  @user-en3fy3qk6i10 ай бұрын

  Hi Sir thank you very much for this very informative video. Sir, where to get that extensions for bridge both civil 3D and Revit please?

• 
  @ayaCH2558 Жыл бұрын

  Great

• 
  @inzagifhall Жыл бұрын

  dear john thanks for efforts & great explanation, could you plz share the csv file called "timeline", thanks Boss

• 
  @adamstehr Жыл бұрын

  Thanks for the video. I realize this is an older video but thought maybe it could help you to tell you a mistake I have made with conversions imperial/metric and state plane. Be careful with your imperial to metric conversion. using .3048 you're using international foot conversion not US foot or survey foot. on small numbers it doesn't make much difference but large numbers like state plane coordinates it makes big differences. Here in Oklahoma it makes about a 4 foot difference. lesson learned the hard way

• 
  @ricolinveerlal5282 Жыл бұрын

  very good we will be so greatfull if you can revise it version 2023 Civil 3D

• 
  @thusithaamarasinghe7824 Жыл бұрын

  Can you please explain the design of the vertical pipe using SSA?

• 
  @masoodalikhan9870 Жыл бұрын

  Should we design sewer and storm drainage separately or jointly using SSA and hydraflow?

• 
  @castled71049 Жыл бұрын

  After setting up SSA and run the analysis, I get the error message "INF is not a valid floating point number." Any idea how to fix this problem? Thank you.

• 
  @abdullahn98273 ай бұрын

  it provides the error number. Get that and look in help manual, you will know whats the error

• 
  @ilhamlaarej7851 Жыл бұрын

  Video for putting your own softs on or is that possible. I can softbox so would like to up load my own softs.

• 
  @rafaelitalo7066 Жыл бұрын

  Once I Get In The Top Ten s Your My Credit ;)

• 
  @normanbuenaflor382 Жыл бұрын

  TNice tutorialS WAS SOOOOOO HELPFUL!!

• 
  @XamofSsadda Жыл бұрын

  .

• 
  @AutoCADRevitByju Жыл бұрын

  Good information, do you created any Technology based Civil 3d video, Like Electrical power cabinet, Electrical Duct & 3D asset tagging. Please upload if you have , thanks @john Sayre

• 
  @pearlsibisi9382 жыл бұрын

  Hi John, Thank you for the video. Is there any way to design for the 1:200 year storm event using the rainfall designer? I noticed that it ends on 1:100 and I would like to analyse other return periods.

• 
  @karabusch28412 жыл бұрын

  Anyone know how do you reverse flow direction in version 13.4.133.0?

• 
  @andrewsamuda32662 жыл бұрын

  Great video. What was your simulation period and how did you select it

• 
  @andrewsamuda32662 жыл бұрын

  excellent

• 
  @aysunguler60712 жыл бұрын

  Great video! Thanks

• 
  @123rockstar20102 жыл бұрын

  Sir, how to do you solve bowties in curb returns for intersections? I am new to Civil 3d.

• 
  @kaicheng60272 жыл бұрын

  godlike sharing, thanks!

• 
  @marcelinodiaz81332 жыл бұрын

  Hello John, where can you get the IDF curve table files?

• 
  @marcelinodiaz81332 жыл бұрын

  This tutorial is explained very well and explains everything step by step! Thank you so much for making this tutorial! It has been extremely helpful!

• 
  @abuomeribrahim72202 жыл бұрын

  can you submit the drawing for practicing?

• 
  @jasonwatt22742 жыл бұрын

  Hi John, is there an email I can contact you on in regards to some VR questions I have. Thanks Jason

• 
  @emmanueladewumi86512 жыл бұрын

  Hi John, Please how did you get your external flow to be 3 CFS? Did you get it from the run-off discharge? Which rainfall return period did you use? Thank you.

• 
  @FranCoVids2 жыл бұрын

  So, what is the setup for an infiltration pond design? Also, how can you obtain the treatment flows?

• 
  @Rohitrawat-rh3np2 жыл бұрын

  Hi there nice informative video. I am struggling to edit projection and crossing of solids in my sections. how to turn them off together for whole section groups ?

• 
  @benzonjhermogeno2 жыл бұрын

  Great video, can I have the retaining wall sub-assembly

• 
  @rabingautam61102 жыл бұрын

  what a great video. Thanks Sir!!

• 
  @royellamil93543 жыл бұрын

  How to use or insert our own company border?

• 
  @anwaralattar13 жыл бұрын

  Hi John - could you please share/send the tutorial file/s ?

• 
  @vforvasco75853 жыл бұрын

  7:50 does this website has data of the rest of the world as well?

• 
  @yvesbalagtas64243 жыл бұрын

  Great work! Hoping u upload a video related with Sanitary Landfill design!