This Channel is all about
👉 converting vans into a campers
👉 servicing, repairing them and more …
👉 Servicing and repairing cars mainly on driveway
👉“HOW TO ” videos which can help you perhaps with your own car 🚗, van 🚐 .
If you share same passion or just interested in this sort of subject subscribe now! Respect ✊ Peace ✌️ and Love ❤️
Пікірлер
Easily the best how video on KZread plus the video on bumper removal is perfect...thankyou.
Great Video!...a big thanks for your channel.
Really helpful, thanks for posting, btw do you need to drain the gearbox oil for this job?
@@joeblackman100 hi, no you don’t have to !!!
I'm struggling to select gears I was replacing clutch kit
Great video, thanks for making… what anti rust spray are you using on the fresh metal cuts?
@@cattmuff5305 hi, I’ve used Parkside Aluminium Zinc Spray. But I’m sure if you go to ur local hardware store you’ll find something like red oxide paint or similar… 👍 🤜
Great video
Hi ,did u buy the tyres in ireland or online??also how much are 4?👍
Hi, had to buy them online … my local Tyre shop wouldn’t supply them:/ Just under €200 a piece ... Great tyre and looks badass too 😆 🤘🛞 Thank you for watching 👍 🤜 www.tyreleader.ie/car-tyres/bfgoodrich/all-terrain-t-a-ko2/235-70-r16-104-101s-558470
HOW TO replace rear brake pads VW Tiguan 👉 kzread.info/dash/bejne/g66bpdOhk5vdhJc.htmlsi=-roJIFpnUl7-bSuN
HOW TO replace front brake pads VW Tiguan 👉 kzread.info/dash/bejne/oWamysOect28Yso.html
It was a great video, I learned a lot. Could you tell me at 15:20 in your screen what is this number 372 and if you press the left button the -99 number?
@@netezoeger 372 means days … next service in 372 days or 20000km which ever comes first… -99 meant what I overdue my inspection by 99 days … hope this helps! 👍 🤜
Great video my friend , very well explained
I am bleeding it but the clutch gets stiff, then gets loose again after a few pumps. What am doing wrong?
@@rowanabrahams9280 not sure, but keep pumping it unit all air is going to come out.. make sure you keep topping up bake fluid as well. Hope this helps 👍 👍 👍
@@jersovauto Thank you will try
Hi iv just got 2 panels pretty much like your and was thinking off fitting the way u have done with the cross bars have u had any issues with the Ventura tunnel effect ?
@@user-qd7sn5xu2i Hi, it’s a great way to mount them!!! Very secure and no wind noise at all!!! 👍 👍 👍
really helpful video, thanks mate
@@Olleh987 Your views and comments are my greatest motivation!!! 👍 🤜
I am struggling to do the last step. I cannot get the bleeder valve pipe into the “2nd position” I am trying to push the metal clip downwards and the pipe to the right? Is this correct do you have any tips. No fluid or air is coming out.
@@curtisyoungs9382 Yes it is correct! Clip down and push right at the same time until it stops… Make sure you have plenty of brake fluid in your reservoir!!! On max mark..do not let it run dry!!! If still struggling perhaps try to prime master cylinder itself be injecting brake fluid with syringe 💉 take needle off , fill syringe with brake fluid, take top tube off which goes to ur master cylinder…take it off there it connects to ur brake fluid reservoir and inject brake fluid into ur master cylinder… pump clutch pedal…perhaps press in once…then inject more brake fluid… reattach tube back … and try to bleed it now… Hope it helps!!!
Where are you based buddy?
@@tkdleeds Meath 👍
Great job from Owen
@@willquigley5633 Hey, Owen! Great to hear from you 👍
Some Chinese diesel heaters can't be installed on a side bracket. I bought one and same thing as yours happened over fuelling. My heater started popping with flames out of it😅😮. I thought it was going on fire. Instead i bought a autoterm 2d instead expensive but they last longer
@@finno123456 Probably autoterm is a way to go.. Nowadays they r more affordable… my Chinese heater works fine now although I had to replace heater temperature sensor twice now…:/ in video it smoking cos I primed it to many times and flooded it .. Diesel heater is a great piece of kit! Love mine! 👍 🌡️ ☀️
Perfect doing same thing today for the first time great video
Great video I feel I can do mine now but need to ask is the seal part a part of the stub or a completely different part as I have leakage too. Or would leak be because the stub is knackered which it is ta
@@scottkelly-e5x New stub comes with new seals and bolt…since my seal inside gearbox which surrounds ur stub was fine I didn’t bother changing it.. perhaps when I will be changing stub next time I’m gonna have to do it. It’s really not that difficult to do.. u just need to pry an old one and then carefully place new one with light tap of rubber mallet. Good luck with yours! And thanks for watching!!! 👍 🤜
@@jersovauto thank u sir
Why have both slider and folding seat, wouldn't the swivel be redundant if you fold the seat. Also during the first step of the M10 spines if you slacken the bottom 2 then it will lift easier
@@warrensurtees6552 Just gives you versatility … u can swivel, fold, slide it… u can swivel it first and then fold and slide it… use as a table for example and so on… Only though about slackening it afterwards:) learn from my mistakes 😜 Thanks for watching 👍 🤜
Thanks your Video help me A lot i have a Nissan tiida 😊
A lot of models seems to be sharing same parts which makes sense really! I’m glad it helped you! 👍 🤜
Hi there, great video. I'm about to out a 300w solar panel on the roof of a t4. Where did you the cross bars, would be a better job than drilling but with the larger panel it will need to be a lot more secure with the wind catching it. Cheers
Top job! Just reminded me that I have 2 brand new bottles in my garage that I bought about 4 years ago after I broke down, which was the dreaded driveshaft issue. I need to pull my finger out and change it!! You overtaken me with subscribers too so send some my way please 😂
When I’ll be somebody like Mat Armstrong I’ll send some subscribers your way not a bother! But now it’s a little bit early stage yet 😂 😂 😂
@@jersovauto 😂
HOW TO change Transmission Fluid /Gearbox oil 👉kzread.info/dash/bejne/Z31-vJmLoZynldY.htmlsi=zY4JUTCuagONeSco
HOW TO replace Drive shaft and Stub shaft VW Transporter 👉 kzread.info/dash/bejne/pZd2l6abqZC4edo.html
First 1like
you just on time mate. cheers👌
Hi, has the solar panel bracket stayed attached ok, with the screws from underneath?
Rock solid! No problem at all 👍
@@jersovauto I’ve got the same roof bars, a bigger panel, the prob I might have, is getting cable through, as I’ve got a ceiling and cupboards fitted etc
@@michaelwilliams3861 yeah ideally you would do all your wiring before furniture fit out. But nevertheless go for it !Solar ☀️ is great addition to your camper!!! Especially with a weather we r having now!!! 👍 👍 👍
@@jersovauto I’m definitely doing it, I’ve got the solar panel on the living room floor as well speak. I think about the cable laying after the panel is up. Where are you by the way?
Ireland 🇮🇪 ✌️
Perfect timing, I will get the parts tomorrow :) Good except for the torquing. Seems it was above 200Nm already and never "jerk" the torque-wrench.
I should probably invest into better torque wrench! Plus I would be paranoid nut 🔩 can come off since in has no split pin on shaft… just a nylon lock..Thanks for watching and commenting 👍 🤜
Good video, what engine is yours and am I right that the stub axel shaft is only on the offside
It’s 2.0 tdi CAAB 75kw , you r right stub is only on offside. Thank you for watching 👍 🤜
How much would you cost too repair one for a customer?
Good question! I have never actually thought about it. I’d say in around €80 would be a fair price for parts and labor…Why? U thinking about doing this for living? :)
No lol I need mine done and couldnt be arsed doing it myself ha seems like a lot of bother ha
@@DeanHarkin-wx1cd you should really give it a try! It’s not that difficult and gives you sense of achievement at the end 👍
I've got some old stainless steel exhaust tubes. Might make a nudge bar with it. A welder is a great investment.
gromit is there incase u want rear view camera i think
with out repair kit what would you do ?
I’ve seen people putting bolts through with round shape head.. looks alright. If r on a budget and need a quick fix I’d say it’s way to go… not sure about water tightness or now days you can get brand new aftermarket handle … the only thing is it comes black and not even primed… 👍 hope this helps 👍 Thanks for watching 🙏
Thank you for confirming the piston retraction. I've not long finished my first ever rear pad replacement on my Audi A5 with all going OK until I heard someone say you have to wind back the piston or it could lead to a damaged calliper. I genuinely didn't know this as mine was pushed back easily, like the front ones. Thank you for your short explanation in this as I can now breath a sigh of relief. Out of interest how much does the rear brake pads get used for braking, do they get used in conjunction with the front ones or are they more for emergency braking and handbrake? Reason I ask is the front callipers are bigger so why aren't the ones at the back the same. Thanks
Glad you found my video helpful!!! In regards of rear brakes they do get used at the same time with front ones .. front ones one larger simply cos they take more load force of ur entire car 🚗 weight and rear ones kind of helping them to slow ur car down… this is how law of physics works.. unless in reversing, but u don’t reverse at the crazy speed I hope 😂 some cars like Mercedes and Nissan for example using rear brake pads for braking when driving and brake shoes for handbrake… hope this helps and thanks for commenting!!! 👍 🤜
@@jersovauto Nice one thanks for that and yes it does make sense now you've explained it regarding load. I went out afterwards to bed the brakes in and check they were working but wasn't sure how much they were actually getting used. I now know they are, well until I get my MOT next week and that'll be the real test. Thanks again mate. You got another subscriber.👍
how did you push the pistons in if you don't mind me asking?
@@care2000 I used one of those piston retraction tools I got from Amazon.
@@care2000 first you have to put ur rear brakes into the “service mode” using an OBDII scanner… and then use brake caliper rewinding kit to push the pistons back in… 👍
Great work thank you for sharing
Hi you did a good job do you pay for obd scanner subscription or it’s free?thanks
Thanks! It comes with 1 vehicle 🚗 free for life .. any additional is a subscription around €25 for a year:(
Hi thanks for replying.
È assurdo vedere come nessun possessore di qashqai j10 non sappia riporre correttamente in sede l'attacco della cintura di sicurezza del terzo posto, lasciandola sempre penzoloni
Heita I have nissan almera N17 1.5 model, I'll be watching your videos. Am in Mzansi
Isn’t it possible to just buy the plastic that breaks off , I think it’s called a clutch master cylinder buckle/clip , it’s a white plastic thing right ?
I’d say everything is possible if u can get spare parts… Complete master cylinder price starts from around €50 if you shop around…So it was no point trying to rebuild it considering it was in service for nearly 15 years 🤷♂️ But would be interesting to see someone would actually rebuild it 👍
Just happened to me, such a bad deign relying on plastic clips that were clearly going to break with time.
...The kitchen pod looks awesome!..gonna make one for my van now,thanks for the video...cheers...T
HOW To Install Solar Panel VWT5 & T6 👉 kzread.info/dash/bejne/mmV9l9SgebrRqtY.html
Thank you for the video I’ve got the t5 barn door I’m going to do the same
Hi what size was your hose for bleeding the clutch after please ? Useful video for qashqai owners who have this problem , thanks .
From top of my head it was 8mm outer diameter and 5 mm inner diameter clear pvc tube.. u can buy it on Amazon . 👍 Thanks for watching 👍
@@jersovauto thank you .
Fantastic thanks so much.
I get my roof rails tomoz with two cross bars like yours and was wondering how to fit the panel to the cross bars and if ive watched tiur vid right you used self tapping screws to screw up into the cross bar is that what you used mate???
Hi, tek screws will do the job, but if u want to be 100% sure u can drill hole 🕳️ through crossbars and use bolts and nuts. But as I said I’ve used tek screws with no issues!!! Something like that: www.screwfix.ie/p/easydrive-flange-self-drilling-stitching-screws-with-washers-6-3mm-x-25mm-100-pack/4259h Thanks for watching 👍