Уважаемые друзья, рад приветствовать.
Канал в своей основе посвящён ремонту, обслуживанию и апгрейду студийного звукозаписывающего оборудования, а также изготовлению кастомных приборов по схожему профилю.
Кроме того, имеются профессиональные навыки электромонтажа, разработки силовой автоматики под конкретные задачи, а также ремонта силовой электроники (в частности, частотных преобразователей), но всё это скорее побочный вид работ.
Канал создан для:
- помощи технически подкованным владельцам техники и оборудования в осуществлении самостоятельного ремонта и апгрейда их устройств, используя мои видео как технический мануал, подсказку или же как средство вдохновения для работы;
- личного рабочего портфолио и отчёта по сделанным ремонтам;
- развлечения (почему нет!) 😀
Почта для связи:
[email protected]
[email protected]
Пікірлер
What a great video!!! This is exactly what is wrong with my unit, Can you give me a list of caps i need to buy to complete this repair on my VS-2480?
Can anyone point me towards someone that does VS2480 repairs in Washington state?
G’day Anthony,just came across your video down under in Australia & been having the no sound issue on start up until I restart a few times,do you happen to have a record of the value of the caps so I can pre purchase & possible try to replace myself,as I’m ok with a soldering iron (not amazing like you though),I noticed you remove the solder completely on each cap is there a reason for that ? I will struggle to find a electronics tech so will give it a try,any extra help would g Be fantastic,love all your videos mate Cheers Cj
Holy f*cking shit, you are a Sorcerer! This Maschine’s are awesome, I had a Roland VS2000 CD, the last in line, but the only one with USB! I install one VS8F-2 Board and one VS8F-3 Board into the VS2000 with all 10 released Plugins for the VS8F-3 Board! I sell the Maschine for 8 or 10 Years …today I must say, I wish it back, really! The VS2000 have a great Recording Sound, ok only in 44.1Khz but 16 and 24Bit possible. The VS8F-3 Plug-ins were awesome, the Soundblender Soundtoys are totally once, you get with that sounds out your guitar, you never heard them before in your life, and that‘s Sounds were Great! Nice Job Man …puha … I never can do that, I believe that such Maschine’s you have there, are really really good today, and I think no one else have a VS 2400 like you have…. Cool, really really nice Job! Thanks for sharing this!
Which cable do you use for the switch? minus(-) or plus (+) ?
This is not + or -, this device runs on AC mains current, and the wires/cabling have standard called Line, Neutral, PE. For internal wiring I use 1.5 or 2.5 square mm flexible wire. Input cable - H07RN-F Top Cable 3x 2.5.
@@Anthony_Scott_Studioservice I mean the cable connected to the on and off switch on the front panel. Which route do you use - or +…???
bravo. I did this too, with a 2480. 80 caps on the mainboard alone : ) Have you considered a CF card? Mine boots a full project in seconds, it's unbelievably fast. Somebody (previous owner or repairer) had dropped the back cover onto the custom gate array IC. However, even though the legs are bent, it still works fine
hi master, I ve a problem withthe ground contact of the c414 akg, it's a contact by the grids probably.. what can I do? thks
Music video. Waste of time
I'm sorry for wasting your time))) but it's probably useful to others, not you.
Ух ты! На такую технику я всегда смотрю с восхищением - прям чувствуется былое величие, так сказать) А так же боюсь представить его цену - как сейчас, так и в своё время. Причём для полноценной звукозаписи нужно было ещё очень много всего помимо многоканального магнитофона... Кстати, а какая там максимальная скорость ленты? 76 см (или 30 дюймов) в секунду?
Спасибо за коммент! Да, техника действительно серьёзная, надёжная, и на то время (середина-конец 80х) была нафарширована очень технологичными фитчами и наворотами, существенно облегчающими эксплуатацию. 820-й вообще считается чуть ли не «лакшери» аппаратом )) Могу сказать и про себя, что в процессе студийных или же сервисно-ремонтных работ, я также отношусь к аналоговым рекордерам с должным уважением. Цены на конкретно эти машины за рубежом сегодня в пределах 7…12 к$, это примерно 1/10 от цены нового. Но и у нас в стране, если не говорить конкретно про Штудера, периодически всплывают в продаже 2-дюймовые мультитреки различных производителей за не очень большие деньги. Но разумеется, эта техника отнюдь не “plug and play”, а требует ввода в строй, периодических процедур обслуживания и настройки… Да, макс.скорость 30 ips , но на этой скорости завал НЧ происходит раньше, впрочем как и на любом магнитофоне (тут увы физика, ничего не поделать), да и расход носителя серьёзный, один рулон 762м - это 16 минут записи. Поэтому 30-ка всегда используется под свои определённые задачи.
Nice video! Super professional craftsmanship, v impressive :D Asking for a personal project of mine: Do you think it would be possible to make this same box, but switch out the Schuko sockets for automotive USB outlets? I like the safety features of the Schuko sockets, but I am having trouble finding USB outlets that have similar safety built in and also safe to use with rocker/toggle switches.
Thank you for your rating and kind words! Yes, of course, you can install any sockets for yourself in such a design, even USB, but it’s true that in this case the distributor will serve to supply DC power to USB devices (why not!). The device in this video is for connecting loads operating from a 230V mains, so I used Schuko with covers.
Thanks for this excellent video, am refurbishing one and this helps a lot!
beautiful soldering work :) bravo! I see so many sloppy soldering jobs on youtube with people splashing solder everywhere and almost causing shorts between connections (or not having their iron hot enough). the dipping of the cap leads in flux before soldering was a nice touch. full points sir!
Very nice work!
Thanks, very informative. Appreciated!
thabk Y Anthony, this was very good to know!!❤
Its just replacement hardisk with ssd without instaling original os to ssd ?
I love the project, but it's not really a "how to," vid unless you have a fully loaded electronic manufacturing workshop. I sure wish I had all that tech stuff in my little amp workshop :)
Video excelente, obrigado por postar um video tão detalhado e com tomadas de video que ilustam cada etapa dessa manutenção. Parabéns !
Ottimo lavoro, complimenti, devo farlo anche io sul mio vs2480 👌
Thank you and good luck in repair process!
@@Anthony_Scott_Studioservice To do the work I need to have the diagram with the values of the capacitors?
Greetings Anthony. I sent you a few words two months ago on your excellent video---also mentioned having an MX-5050 bii-2 having starting issues. I hear a few seconds of arcing sounds that I believe were coming from the mechanical safety switch, but after further research appears to be coming from the capstan motor. This only happens during initial play or if the unit has sat for about 30 minutes after initial play. Sometimes, I don't get the arcing sound and the motor does not come on at all after moving the right tension arm. Your input would be greatly appreciated--and keep up the great videos.
Thanks to you, my VS-2400 should live 20 more years.
Thanks! 🙏😇
Hi ! nice video. I'm not fluent english : May I ask you if I have a small variation of speed 15 and i wonder if you have the Capstan drive electronic schematic so i can follow signal and find the problem ?
The Roland VS -2400 can use AC electric 220 v. or not?
All VS-2400 machines have a universal internal power supply of the same schematic design and work perfectly from a mains of 100 to 240 volts. The voltage value on the back panel label indicates compliance with country-specific export requirements only, so don't worry.
Beautiful work! What do you use to soak up the water from the edges?
Hey man thanks - Bought a 50 year old amp yesterday; knobs were filthy as they can get, but this worked great!
Pl I need some help with my vs2400, for starting up
motor fader 13 pcs how much? Where can buy ? I have same VS 2400 but now motor fader it's broken
Hi, I got a Roland VS 2480. When I turn it on, it says “Sub System No Response”. Is it possible to fix it or is it dead? Do you have experience with this? Thank you
Can you build one for me? I’m serious
what an afternoon this lady had! for a first a first effort, it ain't half bad.
This is Art!
Thanks!
magnificent Anthony!!!! your are in deed the scientist of Roland vs 24"s ...exactly the problems i was experiencing as well...thank you very very much!!!
My 2480 is experiencing all the same symptoms that you demonstrated . I have been looking for a repair shop for years now . unable to find anybody willing to attempt it .your video makes it seem pretty easy if all I have to do is remove and and replace capacitors on the main board. Then all I would need is the number of capacitors and type, all the chemical , I’m assuming , that’s listed in the service manual on the main board. Note, I am not an engineer of anything, but as I stated, if all I have to do is remove and replace I’m confident that I can manage this. I did also see in the service manual that there are chemical capacitors on the Jack board and analog board as well. Would I need to replace these also? Any assistance in this matter would be greatly appreciated
I replaced all the caps on a 2480, all the surface mount ones and the large filter cap. The PSU I left alone. It's easy to read the values off the side of the caps. It's difficult to open up and access the boards but with patience you can get it running again.
@@robinsutcliffe-video_art I'm about ready to take on this project I have done soldering before so i should be able to handle this, Where did you go to purchase the caps? Do you remember how many different values of caps there was?
Excellent video....Purchased a beauty that looks just like the one you repaired and started to have issues with it a few months back. Going to study your video some more and do some research to see if I can stay on top of it's issues. Thanks for posting...
Hey Anthony. first of all, thanks a lot for posting the video. If possible, id very much appreciate if you could post the schematics, as the video in and on itself doesn't give much to work with
Great video, as always, Anthony! The 820 transport is just crazy. I could buy that machine just to sit and watch its amazing tape handling.
Omg yes 🙌 finally a video on tension arm service/lubrication, I have the service manual for mine and this procedure/alignment is not listed anywhere. Finally I can service my mx5050. Thank you so much for doing this video. I would love to see you do a service video on the mkiii-8 mx5050 or even the Teac 80-8... love your content! Just subscribed! Cheers!
Да это победа 🎉 Монстрик реальный ,!
I can't see how that sata soldering fixed the m24 16 channel record issue. Could it have just been a faulty connector ?
I have a mixer that needs caps replaced ! Help !
Anthony really good video, i own an OTARI MX 50 and 2 mx 5050's and would really like to get them thoroughly serviced how would i reach out to you to arrange that if possible Thanks
Send this video to the folks at Neumann :P
Done watching✅ New subcriber thanks🫡🫡🫡
My switch actuator was jammed due to residue from the double-sided tape that had leached into the actuator opening. I was able to disassemble and clean it adequately without unsoldering.
Thanks for recording this
What is that black sealing goo?
This is regular metal paint. I apply it to secure the threads to prevent the possibility of unwinding (since some of my box distributors work not only in the studio or at home, but also in sound rentals and are often transported). Thanks!
What was the value of the R23 resistor?
560 Ohm 1 watt
I have a Roland V2400 I would like to sell it.
A simple line filter will do. No need for such a complicate circuit. Another stupid product for audiofool!
You're insane. This circuit is completely isolated via transformers, line filters won't touch this. Better go back to school before trying to be a fat know-it-all online.
Such craftsmanship and attention to detail. This is incredibly relaxing to watch and i'm so jealous of your work. Bravo.
Thank you for your high rating and kind words!