What tool is that? I’m in the middle of doing mine and I need it done today. Where can I buy one
@dtlife61559 ай бұрын
The tool I used was a Ryobi oscillator bit. Best wishes for you. Any hardware store should have you set.
@dtlife61559 ай бұрын
Do you have an '03 with this exact oil rail and 10.9 bolts? Do not listen to the torque specs if you have 10 mm head socket like mine. If it's a torx you can go tighter. I didn't do a video on it but The bolts can only take about 12 torque pounds. Not the 33 the internet was telling me.
@billycarroll36679 ай бұрын
I have an 03. Just like you said all the videos only show newer 04s and up and when I took the valve cover off I was like well this looks different.
@billycarroll36679 ай бұрын
Seem to be 8mm bolt head. Haven’t put a socket on it yet. When I saw that I just stopped because I need to change #7 injector and the bolts by the heater box were a bitch and I wasn’t putting it back together just to go to Home Depot not even 2 miles away to come back and take it apart again
@dtlife61559 ай бұрын
@@billycarroll3667I bet the passenger side is a real pain! Yes 8mm sounds right. Just don't put them back on with the torque wrench and try to be as consistently hand tight as possible. I tried twerking one to 33 ignorantly and ripped the head off. Thankfully threads were above the block but I had to remove the rail again which made it another day project.
@hotrod6919 Жыл бұрын
Good luck! The average mechanic takes about 6 months to wrap their head around the heui and hpop system on a 6.0 The problem with alot of scan tools is they read only the psI and not the voltage where the psi reading is possibly a inferred reading due to bad icp but voltage never lies
@dtlife6155 Жыл бұрын
Thanks for your feedback. I'll keep it posted how it goes. There is so much to understand it's crazy you're right.
@hotrod6919 Жыл бұрын
@@dtlife6155 yeah idk jack shit few years ago bout Diesels let alone 6.0s when i bought my 03' but after few months of going down a exspensive rabbit hole the worst thing happened I fell in love with the POS I even write my own custom tunes Watch Diesel tech Ron on youtube He passed away few years back but hes was a 6.0 guru and download the 6.0 bible
@dtlife6155 Жыл бұрын
@@hotrod6919 Ron's videos are so priceless! Have watched many. What's the 6.0 bible? Like a all included manual? I'd be down to get that. Didn't get a manuel with this truck unfortunately...
@hotrod6919 Жыл бұрын
@@dtlife6155 its basiclly a manual from wire schematics to troubleshooting common failures and sensor locations ive downloaded it free a few times make sure its for 03' to early 04'
@dtlife6155 Жыл бұрын
@@hotrod6919 Awesome I will definitely check that out! Thanks!
@DoctorRickSanchez Жыл бұрын
_Hate to break it to ya, but they circled the problem._
@dtlife6155 Жыл бұрын
What do you mean? It's the oil pressure. What's the problem
Пікірлер
HHOP gave up. Runs great now.
What tool is that? I’m in the middle of doing mine and I need it done today. Where can I buy one
The tool I used was a Ryobi oscillator bit. Best wishes for you. Any hardware store should have you set.
Do you have an '03 with this exact oil rail and 10.9 bolts? Do not listen to the torque specs if you have 10 mm head socket like mine. If it's a torx you can go tighter. I didn't do a video on it but The bolts can only take about 12 torque pounds. Not the 33 the internet was telling me.
I have an 03. Just like you said all the videos only show newer 04s and up and when I took the valve cover off I was like well this looks different.
Seem to be 8mm bolt head. Haven’t put a socket on it yet. When I saw that I just stopped because I need to change #7 injector and the bolts by the heater box were a bitch and I wasn’t putting it back together just to go to Home Depot not even 2 miles away to come back and take it apart again
@@billycarroll3667I bet the passenger side is a real pain! Yes 8mm sounds right. Just don't put them back on with the torque wrench and try to be as consistently hand tight as possible. I tried twerking one to 33 ignorantly and ripped the head off. Thankfully threads were above the block but I had to remove the rail again which made it another day project.
Good luck! The average mechanic takes about 6 months to wrap their head around the heui and hpop system on a 6.0 The problem with alot of scan tools is they read only the psI and not the voltage where the psi reading is possibly a inferred reading due to bad icp but voltage never lies
Thanks for your feedback. I'll keep it posted how it goes. There is so much to understand it's crazy you're right.
@@dtlife6155 yeah idk jack shit few years ago bout Diesels let alone 6.0s when i bought my 03' but after few months of going down a exspensive rabbit hole the worst thing happened I fell in love with the POS I even write my own custom tunes Watch Diesel tech Ron on youtube He passed away few years back but hes was a 6.0 guru and download the 6.0 bible
@@hotrod6919 Ron's videos are so priceless! Have watched many. What's the 6.0 bible? Like a all included manual? I'd be down to get that. Didn't get a manuel with this truck unfortunately...
@@dtlife6155 its basiclly a manual from wire schematics to troubleshooting common failures and sensor locations ive downloaded it free a few times make sure its for 03' to early 04'
@@hotrod6919 Awesome I will definitely check that out! Thanks!
_Hate to break it to ya, but they circled the problem._
What do you mean? It's the oil pressure. What's the problem