I know this vid is for the cam but I can’t help but admire your catch can setup
@alitutar853321 күн бұрын
Boost psi ?
@GarageAbstract21 күн бұрын
14 PSI. All specs are in description
@codynichols12Ай бұрын
is that the full motor build in the description ?
@GarageAbstractАй бұрын
Yes, it’s a very simple setup
@jonathanrice-exec11Ай бұрын
Nice! Sounds great! Is the yellow car TD06 now as well? It'll be nice to swing by the shop again once I'm living in town after next month
@GarageAbstractАй бұрын
Yes! Yellow car has TD06-20G. And yeah, swing by and hang out for a bit once you’re back!
@teamd-frog1260Ай бұрын
perfect sounds
@reubenmorris4872 ай бұрын
My first DSM with HKS 264/272 sounded like this with slightly less chop and pop.
@kornboyjr64192 ай бұрын
What rear gear ratio is it running?
@GarageAbstractАй бұрын
4.08
@esoteric__3 ай бұрын
Which bov was this thing equipped with? Sounds like old HKS. Seen that some guys who ran no BOV with the RX suffered catastrophic failure by snapping the shaft due to the RPM's that the billet wheel achieves and the sudden deceleration was enough to cause the shaft to snap off at the base of the inducer wheel. 3 pulls on a dyno and the thing calls it quits.
@Zilvia333 ай бұрын
Delicious music 🤌🏾
@ej2085 ай бұрын
17 lbs in bars?
@scareyaf4 ай бұрын
About 1.2 bar or so. Google exists my dude, use it.
@user-lp5wb5wg6v5 ай бұрын
What BOV? The car sounds great!
@zoic6135 ай бұрын
That’s no bov.
@JohnHonza6 ай бұрын
🥵🥵
@ItsMarkBernardo7 ай бұрын
hell yeah brotherr
@um-cara-no-impreza7 ай бұрын
rx7 ?
@GetBusyDrift9 ай бұрын
that shit sounds so wet
@pistnbroke7369 ай бұрын
I have finally copied your set-up. Sounds similar, not as lumpy now it's tuned. I also funny enough, have the same wheels you have on the front 😂 just about to throw on a GTX3076 turbo with a ramhorn high mount manifold.
@EvThaFunkyHomosapien10 ай бұрын
Any reason going for the hks cams vs tomei poncams?
@GarageAbstract10 ай бұрын
Tomei Poncams are a great drop-in replacement without needing to further upgrade the springs/retainers. However the 258 duration and 11.5mm lift of the poncam doesn’t offer as much as the 264 duration, 12.0mm lift of these HKS step 2 cams.
@EvThaFunkyHomosapien9 ай бұрын
Thanks for the reply! I failed to see they were a higher duration. Do you have a preference for 256 duration cams between hks and tomei?
@dennisrobinson80087 ай бұрын
Hi, So the 258 poncams are a direct drop in and don't require a tune, but the 264 cams will?@@GarageAbstract
@GarageAbstract6 ай бұрын
@@dennisrobinson8008 I recommend a tune with any cam upgrade. The poncams are “drop in” meaning they don’t require further valve spring or retainer upgrades, whereas the HKS 264 cams do
@jaredsannicandro465811 ай бұрын
exhaust mani?
@GarageAbstract11 ай бұрын
Trust mid mount
@14dose Жыл бұрын
What size and material is the dose pipe man?
@GarageAbstract6 ай бұрын
It’s a Trust air intake kit. Aluminum, opening up to 80mm at the MAF
@Understeerking Жыл бұрын
🎶🎶
@jeremynazario3971 Жыл бұрын
What oil do you use?
@GarageAbstract Жыл бұрын
Motul 300V 15w-50
@jeremynazario3971 Жыл бұрын
@@GarageAbstract Stock block never open, stock oil pump and stock oil filter? right?
@@GarageAbstract okay perfect I just wanna ask bc I have the same spec as you but the only difference is that I got 272 cams and I use 10w40 but when I use try to use 15w50 I feel lost of power
@GarageAbstract Жыл бұрын
@@jeremynazario3971 we’ve used 10w40 during the winter time in our street cars, and haven’t noticed any power difference. Both weights are perfectly fine depending on application. No problem!
@colemannon Жыл бұрын
Older video so not sure if you'll see this buuuuuuut....does this have the bigger center resonator like the newer N1s do? If so, how was ground clearance? Planning on getting one of the newer N1s and I'm around the same ride height.
@GarageAbstract Жыл бұрын
This was the older version with the smaller mid section resonator, haven’t had any experience with the newer one, sorry!
@colemannon Жыл бұрын
@Garage Abstract sick!! Thank you for the insight! Might just end up running the rear section then.
@warbvrton Жыл бұрын
Love it. Cool to see another s13 with hurricanes
@roshailsmedia2067 Жыл бұрын
Who needs a rotary?
@Jeremy_Hill_2020 Жыл бұрын
0:05 stustustu
@Jeremy_Hill_2020 Жыл бұрын
that one person: "you did a 13B swap?"
@garybuder4645 Жыл бұрын
Guesstimate on the diameter of the horn? I'm looking at a set but they don't list the size.
@jerxue2194 Жыл бұрын
What fuel pump you are running?
@GarageAbstract Жыл бұрын
Walbro 450
@GabesGarage Жыл бұрын
A lot of improvement from the video on the rain at Lanier 👌 nice that track look very technical.
@owenmccannell58312 жыл бұрын
Man, shoutout to you for answering literally every question in this comment section. Need more people like you in the car scene rn. Much love bro!
@milkteaman510 Жыл бұрын
I wish more people did this, I try to answer as many questions as possible in my video comments. I like to help people figure out their issues and help with their planning.
@trippieredd28992 жыл бұрын
Super nice ride. Who makes the exhaust tips you uave on there I like the angle.
@jw50312 жыл бұрын
What injectors?
@GarageAbstract2 жыл бұрын
Nismo 740cc
@dfr97892 жыл бұрын
can i know what size are your head gasket?
@dfr97892 жыл бұрын
dude can i know ur cams size?, is it a 264/272?
@GarageAbstract2 жыл бұрын
yes, specs are in description x
@dfr97892 жыл бұрын
stock rods and pistons?
@GarageAbstract2 жыл бұрын
Yes
@thomasjoyce83742 жыл бұрын
Is this a speed density setup?
@GarageAbstract2 жыл бұрын
No, N62 MAF equipped
@langgengpratama81062 жыл бұрын
that lumpy sound is an eargasm :3
@cmbrlnd942 жыл бұрын
What fuel is this on? Curious as I have a very similar setup atm and going for a tune in a couple weeks, thinking of maybe going e85. I also have a GT2871R with .64 housing, and HKS cams too but 254/264's instead and I am also running 740cc injectors. Very nice build, love it!
@GarageAbstract2 жыл бұрын
Sorry for the late reply, this was on 93 octane pump gas
@THESLlCK2 жыл бұрын
it literally sounds like half a muscle car, that's so cool
@_yungfrankz16 күн бұрын
Half of 8 is 4 😎
@THESLlCK14 күн бұрын
@@_yungfrankz source??
@leakerror2 жыл бұрын
this is a stupid question but does the gt2871r bolt up to the stock mani? also do you know if gt2835s do or not aswell
@GarageAbstract2 жыл бұрын
Not a stupid question! The stock manifold uses a “T2” turbo flange. So any turbo with a T2 flange on the exhaust housing will work! Some turbos are direct bolt on replacements for the factory T25/T28, while others may require custom intercooler piping and exhaust work. This particular turbo used in the video was just a direct bolt on unit
@leakerror2 жыл бұрын
@@GarageAbstract is this the correct one or is the .86 superior? 0.64 A/R T25 Inlet, 5-Bolt Outlet (Internal WG) w/ Actuator
@GarageAbstract2 жыл бұрын
@@leakerror That’s it! The .64 is what we have installed on this car and it spools much quicker than the .86 version
@leakerror2 жыл бұрын
@@GarageAbstract perfect, thanks man
@cgaige2 жыл бұрын
Hi! Hard question, What do you recommend is the overall best exhaust/set up for the sr20/s13 platform?
@GarageAbstract2 жыл бұрын
Exhaust setup as in from the manifold to the rear of the car? It really depends on your driving style, what sounds you like, etc.
@THESLlCK2 жыл бұрын
@@GarageAbstract that was a wacky question lol. It's never an end-all answer really
@user-hv5ld2ve8p2 жыл бұрын
Ff33333332234
@AdamNZ2 жыл бұрын
Needs the mid mount manifold to get the unique sound.
@GarageAbstract2 жыл бұрын
It has the mid mount manifold haha. The original one from Trust
@slider28282 жыл бұрын
Thats just overlap.... can spread out the lobes to get more mids
@that_blobeye_sti2 жыл бұрын
I love everything about this car, the wing, the wheels, the fitment, sunroof, rhd, like bro I would sell my car so fast for this
@nyleen6 ай бұрын
do it
@cgaige2 жыл бұрын
18 or 19 Minerva’s in the rear?:)
@GarageAbstract2 жыл бұрын
18’s !!
@cgaige2 жыл бұрын
@@GarageAbstract they look perfect!! I’ve been considering going staggered for my stock body Silvia!
Пікірлер
SO freaking cool man
I know this vid is for the cam but I can’t help but admire your catch can setup
Boost psi ?
14 PSI. All specs are in description
is that the full motor build in the description ?
Yes, it’s a very simple setup
Nice! Sounds great! Is the yellow car TD06 now as well? It'll be nice to swing by the shop again once I'm living in town after next month
Yes! Yellow car has TD06-20G. And yeah, swing by and hang out for a bit once you’re back!
perfect sounds
My first DSM with HKS 264/272 sounded like this with slightly less chop and pop.
What rear gear ratio is it running?
4.08
Which bov was this thing equipped with? Sounds like old HKS. Seen that some guys who ran no BOV with the RX suffered catastrophic failure by snapping the shaft due to the RPM's that the billet wheel achieves and the sudden deceleration was enough to cause the shaft to snap off at the base of the inducer wheel. 3 pulls on a dyno and the thing calls it quits.
Delicious music 🤌🏾
17 lbs in bars?
About 1.2 bar or so. Google exists my dude, use it.
What BOV? The car sounds great!
That’s no bov.
🥵🥵
hell yeah brotherr
rx7 ?
that shit sounds so wet
I have finally copied your set-up. Sounds similar, not as lumpy now it's tuned. I also funny enough, have the same wheels you have on the front 😂 just about to throw on a GTX3076 turbo with a ramhorn high mount manifold.
Any reason going for the hks cams vs tomei poncams?
Tomei Poncams are a great drop-in replacement without needing to further upgrade the springs/retainers. However the 258 duration and 11.5mm lift of the poncam doesn’t offer as much as the 264 duration, 12.0mm lift of these HKS step 2 cams.
Thanks for the reply! I failed to see they were a higher duration. Do you have a preference for 256 duration cams between hks and tomei?
Hi, So the 258 poncams are a direct drop in and don't require a tune, but the 264 cams will?@@GarageAbstract
@@dennisrobinson8008 I recommend a tune with any cam upgrade. The poncams are “drop in” meaning they don’t require further valve spring or retainer upgrades, whereas the HKS 264 cams do
exhaust mani?
Trust mid mount
What size and material is the dose pipe man?
It’s a Trust air intake kit. Aluminum, opening up to 80mm at the MAF
🎶🎶
What oil do you use?
Motul 300V 15w-50
@@GarageAbstract Stock block never open, stock oil pump and stock oil filter? right?
@@jeremynazario3971 Stock bottom end, stock oil pump. Greddy thermostatic oil filter relocation, Greddy oil filter, Greddy oil cooler
@@GarageAbstract okay perfect I just wanna ask bc I have the same spec as you but the only difference is that I got 272 cams and I use 10w40 but when I use try to use 15w50 I feel lost of power
@@jeremynazario3971 we’ve used 10w40 during the winter time in our street cars, and haven’t noticed any power difference. Both weights are perfectly fine depending on application. No problem!
Older video so not sure if you'll see this buuuuuuut....does this have the bigger center resonator like the newer N1s do? If so, how was ground clearance? Planning on getting one of the newer N1s and I'm around the same ride height.
This was the older version with the smaller mid section resonator, haven’t had any experience with the newer one, sorry!
@Garage Abstract sick!! Thank you for the insight! Might just end up running the rear section then.
Love it. Cool to see another s13 with hurricanes
Who needs a rotary?
0:05 stustustu
that one person: "you did a 13B swap?"
Guesstimate on the diameter of the horn? I'm looking at a set but they don't list the size.
What fuel pump you are running?
Walbro 450
A lot of improvement from the video on the rain at Lanier 👌 nice that track look very technical.
Man, shoutout to you for answering literally every question in this comment section. Need more people like you in the car scene rn. Much love bro!
I wish more people did this, I try to answer as many questions as possible in my video comments. I like to help people figure out their issues and help with their planning.
Super nice ride. Who makes the exhaust tips you uave on there I like the angle.
What injectors?
Nismo 740cc
can i know what size are your head gasket?
dude can i know ur cams size?, is it a 264/272?
yes, specs are in description x
stock rods and pistons?
Yes
Is this a speed density setup?
No, N62 MAF equipped
that lumpy sound is an eargasm :3
What fuel is this on? Curious as I have a very similar setup atm and going for a tune in a couple weeks, thinking of maybe going e85. I also have a GT2871R with .64 housing, and HKS cams too but 254/264's instead and I am also running 740cc injectors. Very nice build, love it!
Sorry for the late reply, this was on 93 octane pump gas
it literally sounds like half a muscle car, that's so cool
Half of 8 is 4 😎
@@_yungfrankz source??
this is a stupid question but does the gt2871r bolt up to the stock mani? also do you know if gt2835s do or not aswell
Not a stupid question! The stock manifold uses a “T2” turbo flange. So any turbo with a T2 flange on the exhaust housing will work! Some turbos are direct bolt on replacements for the factory T25/T28, while others may require custom intercooler piping and exhaust work. This particular turbo used in the video was just a direct bolt on unit
@@GarageAbstract is this the correct one or is the .86 superior? 0.64 A/R T25 Inlet, 5-Bolt Outlet (Internal WG) w/ Actuator
@@leakerror That’s it! The .64 is what we have installed on this car and it spools much quicker than the .86 version
@@GarageAbstract perfect, thanks man
Hi! Hard question, What do you recommend is the overall best exhaust/set up for the sr20/s13 platform?
Exhaust setup as in from the manifold to the rear of the car? It really depends on your driving style, what sounds you like, etc.
@@GarageAbstract that was a wacky question lol. It's never an end-all answer really
Ff33333332234
Needs the mid mount manifold to get the unique sound.
It has the mid mount manifold haha. The original one from Trust
Thats just overlap.... can spread out the lobes to get more mids
I love everything about this car, the wing, the wheels, the fitment, sunroof, rhd, like bro I would sell my car so fast for this
do it
18 or 19 Minerva’s in the rear?:)
18’s !!
@@GarageAbstract they look perfect!! I’ve been considering going staggered for my stock body Silvia!
@@cgaige Can’t beat a good staggered setup
Bro made an rotary out of SR
sounds like mu 1.9 tdi
garage s hood? dooope
Looks like one