Пікірлер

• 
  @jonnysimps10 ай бұрын

  so what ajustments do i need to do to fit in long poll switches ??

• 
  @iroverice16911 ай бұрын

  I have a problem with the motor not being able to turn when both sides are loaded but it works fine when one side is loaded. Is this a problem with the motor itself not being steong enough or would this be a tolerance issue and the parts not sliding uniformly?

• 
  @keyhubkb11 ай бұрын

  Likely due to tolerance, try comparing printed parts dimension to that specified in technical drawings :D

• 
  @iroverice16911 ай бұрын

  @@keyhubkb is there a difference in torque between the 2 motors you have suggested in the github page since I'm using the TT 1:48 Gearbox DC Motor?

• 
  @Auggie246 Жыл бұрын

  is using PLA fine for the motor? or will it run so hard that it warp the print

• 
  @maiko3414 Жыл бұрын

  hi, are you willing to share the switch break-in count code and how to do it? that would be great!

• 
  @ginobretana4110 Жыл бұрын

  this is awesome man, thank you for sharing

• 
  @pine2850 Жыл бұрын

  where did you get that motor?

• 
  @bli555552 жыл бұрын

  hey man was wondering if theres any other bearing usable for this instead of the 0306 thank you 🙏🏽🙏🏽

• 
  @jonnysimps10 ай бұрын

  Have you found the alternative??

• 
  @dethlordful2 жыл бұрын

  Were can I find the code the the nodemcu?

• 
  @Akino692 жыл бұрын

  Hey can i ask a question. That 30% infill will be enough ?

• 
  @doingmusic11932 жыл бұрын

  Not even this can save browns

• 
  @kietskeeb2 жыл бұрын

  genius

• 
  @mith21462 жыл бұрын

  What parts did you use to count the switch depresses? Was there a kit or do you have a bom?

• 
  @keyhubkb2 жыл бұрын

  I made a hotswap pcb to pair with one switch and track when it depresses with an ESP32 development board

• 
  @mith21462 жыл бұрын

  @@keyhubkb that's the part that has me, did you design a single pcb and have it manufacturered locally or something? I've found some online that have 5x5 layouts that seem like you could "snap" one off but it also appears to possibly be traced together.

• 
  @desmond53732 жыл бұрын

  Hello, I wanna ask if the motor and the Female USB C to 2-pin 22 AWG Wires are soldered?

• 
  @mith21462 жыл бұрын

  They are soldered by you after procuring both parts

• 
  @swide27502 жыл бұрын

  4:12 oohhhh smart also can test any printing defects like double clicking if timed correctly with motor rpm

• 
  @embetoon2 жыл бұрын

  Hi bro, thank you for sharing your design. I have a question: is that Flat Profile Keycap really necessary? Can I just use Actuation Plate alone to press switch?

• 
  @Someguy5k2 жыл бұрын

  If you check out the operational guide video, it shows that the flat keycaps in addition to the plates are in order to perform off center actuation.

• 
  @embetoon2 жыл бұрын

  @@Someguy5k Got it! Thank you, bro!

• 
  @baoduahau2 жыл бұрын

  what is the counter machine bro?

• 
  @sharp87482 жыл бұрын

  how many acuations

• 
  @maanta4592 жыл бұрын

  are these centered actuations only?

• 
  @nathanma26712 жыл бұрын

  There is a off center plate

• 
  @HoangAnhNguyen-gy4tq2 жыл бұрын

  0:44 me thinking what kind of scratchy linear it was lol

• 
  @lauhernsean61792 жыл бұрын

  Hi may i know if the motor is powerful enough to break in more switches at the same time? I plan to use the exact same motor and increase the switch slots. (im a bit greedy hehehe)

• 
  @quinton46472 жыл бұрын

  You are the goat!

• 
  @bohnjack4202 жыл бұрын

  purchase link, please

• 
  @tighterthanbarkonatree57872 жыл бұрын

  Would you be able to upload a comparison between switches, before and after? I wanted to see if there is a sufficient audible difference

• 
  @swide27502 жыл бұрын

  are you asking from this specific method or in general

• 
  @green2gamma2 жыл бұрын

  thats pretty cool, will you produce this for purchasing?

• 
  @keyhubkb2 жыл бұрын

  You can reach me on Discord for commission build or for any enquires on building by yourself!

• 
  @ripfrickingben2 жыл бұрын

  ne counter avail

• 
  @ireneenn43386 жыл бұрын

  Just seen this video.. Btw where u from ?

• 
  @MatteoSione8 жыл бұрын

  Just seen this video..awesome! It's a shame that it hasn't many views because some shots like the timelapses on the beach are so beautiful! Today I'm starting the edit of our school trip in Berlin, hope to get a similar video..

• 
  @keyhubkb8 жыл бұрын

  Sorry for the late reply but thanks for the compliment! :)

• 
  @lukecorry20868 жыл бұрын

  Wow I really liked this video I'm planning on doing one of these videos when I go on my holidays and when I'm old enough to travel on my own around the world you got yourself a new sub

• 
  @keyhubkb8 жыл бұрын

  Hey sorry for the late reply and thanks! :D

• 
  @VisshnuRaja8 жыл бұрын

  What lens did you use for your 700D???

• 
  @keyhubkb8 жыл бұрын

  EF-S 18- 150 mm!