Great video. I have a yt42ls. i wonder why the armor plates are on the bottom of the deck on the discharge side, and top of deck on the other side?
@terrymclaughlin3716 ай бұрын
Nice man! This was very helpful for what I needed in info.. thanks for the video!
@Dave-df1vu9 ай бұрын
after i take my deckk off for the winter i usally wash it and put a good coat of carnuba wax and store it inside
@stevestanley5183 Жыл бұрын
I used a rope around both wheels it helps moving it around
@JohnSmith-ug5ci Жыл бұрын
That is a terrible design for deck mounting and removal. That front double nut is such a bad idea. Now once off you have to fiddle with adjustment over and over until you get it right. NOT GOOD! I have a simplicity brand and the deck removal and installation is so easy. It can be done in less than 1 minute with absolutely no tools. Husqvarna needs to get on board.
@olga1738 Жыл бұрын
You don’t need to unscrew double nut on the front to remove the deck.
@ac7fd3 ай бұрын
it's not, he should just do it properly. the two parts he zip tied up can be removed just like what he calls swaybar. It's really easy to remove and mount, no different than any other name brand mower.
@michaelluke5878 Жыл бұрын
Drop the cigar bit, otherwise good video.
@cartermcclanahan7567 Жыл бұрын
Great video! Was a big help in getting my deck back on after removing my snow thrower!!
@morgan9164 Жыл бұрын
Awesome video, helped me change my belt today. Thanks Brian!
@johnstratton5637 Жыл бұрын
i was wondering how do you install the mower deck on this type of lawn tractor Husqvarna TS 354XD (54") 24HP Kawasaki Garden Tractor
@gobluevictors Жыл бұрын
Fantastic work. Thanks for doing this.
@emilyferguson9220 Жыл бұрын
I am In the video
@jonmeans5289 Жыл бұрын
Where do I put the other end of the anti sway bar, im trying to replace a bent one.
@bferg23 Жыл бұрын
The 90 degree end goes in the frame near the transaxle towards the rear left tire. The front part with the cotter pin hole goes towards the mower deck and attaches on the right ("passenger") side with a washer and cotter pin. At about 10:40 of this video this guy shows it not too bad. kzread.info/dash/bejne/i3ik1MSYk5CuddY.html
@xbigp2 жыл бұрын
Thanks
@mazdarattiman2 жыл бұрын
If you notice the notch design on the front hook, removal of the front wishbone nut is not necessary. Drop, remove rear hookups, slide deck forward a bit to slip wishbone out.
@djlansing27242 жыл бұрын
Thx. Dropping deck tonight & was thinking it looked like front mount could slip out through the slotted part
@allenpoe73722 жыл бұрын
Nice job blowing off the removal of the sway bar, after saying you'd be showing it.
@bferg23 Жыл бұрын
Sorry about that. The sway bar just comes out with removal of cotter pin that I pointed to, and then once the deck is out of the way you can slide the bar out of the hole that it seats in. I also talk about it at 7:51 of the vid. This guy shows the install a bit better at about 10:40 of this vid kzread.info/dash/bejne/i3ik1MSYk5CuddY.html
@Timsengraving2 жыл бұрын
Thank for making this video!!
@cornelc.48952 жыл бұрын
You did a good job going back to the sway bar or what ever is called, it was exactly what I needed to figure out how install the deck back after I removed the snow plow. I wish I took a video when I took it off before the winter as you advised 😉, and of course you can't do it without a good cigar 😊👍!
@johncleaver42452 жыл бұрын
You should let your mower cool down before hosing down…hot bearings ( spindle) + Water is a good way to stuff your bearings.
@CharlieKellyEsq2 жыл бұрын
This is exactly what I'm trying to do!!! That first bolt is awful, I thought I was doing it wrong because I couldn't get it off without extreme force
@jasonbridle79312 жыл бұрын
How many height settings on the dozer blade using that handlebar? Any intermediate positions? Wondering how it would be spreading triple mix on grass
@bferg23 Жыл бұрын
Sorry, I don't have this machine anymore so I can't go check. I have moved to a BX-2380. From my recollection, I only had up or down on the settings, but you can hold it at any height. I would say its prob not the best for spreading triple mix.
@TodayinKansasCity2 жыл бұрын
Any reason you couldn't leave the deck on there? I'd think the extra weight would help.
@CharlieKellyEsq2 жыл бұрын
You have to remove the deck for that anchor point on the front of the mower
@bferg23 Жыл бұрын
Good question, I removed for more clearance for snow while pushing snow. Depending on your environment you could possibly leave it on.
@jim-ed3zt2 жыл бұрын
The sniffing gets a bit annoying
@bferg23 Жыл бұрын
Sorry about that. I cringe when I hear it too.
@TWiumph2 жыл бұрын
Your effort is appreciated. I have the TS 348XD and the process is the same.
@ryangreenway8356 Жыл бұрын
I have the same mower as well…just cracked the deck (support piece under the chute)…lifetime warranty so I’ll be bringing in the deck to a dealer swap everything out to the new deck…never pulled the deck off before so this video was perfect…looks easy enough
@bferg232 жыл бұрын
Wow the quality really downgraded.
@squishiesandmore55244 жыл бұрын
should start a new series called The Adventures of Mountain! its Peyton by the way
Пікірлер
Great video. I have a yt42ls. i wonder why the armor plates are on the bottom of the deck on the discharge side, and top of deck on the other side?
Nice man! This was very helpful for what I needed in info.. thanks for the video!
after i take my deckk off for the winter i usally wash it and put a good coat of carnuba wax and store it inside
I used a rope around both wheels it helps moving it around
That is a terrible design for deck mounting and removal. That front double nut is such a bad idea. Now once off you have to fiddle with adjustment over and over until you get it right. NOT GOOD! I have a simplicity brand and the deck removal and installation is so easy. It can be done in less than 1 minute with absolutely no tools. Husqvarna needs to get on board.
You don’t need to unscrew double nut on the front to remove the deck.
it's not, he should just do it properly. the two parts he zip tied up can be removed just like what he calls swaybar. It's really easy to remove and mount, no different than any other name brand mower.
Drop the cigar bit, otherwise good video.
Great video! Was a big help in getting my deck back on after removing my snow thrower!!
Awesome video, helped me change my belt today. Thanks Brian!
i was wondering how do you install the mower deck on this type of lawn tractor Husqvarna TS 354XD (54") 24HP Kawasaki Garden Tractor
Fantastic work. Thanks for doing this.
I am In the video
Where do I put the other end of the anti sway bar, im trying to replace a bent one.
The 90 degree end goes in the frame near the transaxle towards the rear left tire. The front part with the cotter pin hole goes towards the mower deck and attaches on the right ("passenger") side with a washer and cotter pin. At about 10:40 of this video this guy shows it not too bad. kzread.info/dash/bejne/i3ik1MSYk5CuddY.html
Thanks
If you notice the notch design on the front hook, removal of the front wishbone nut is not necessary. Drop, remove rear hookups, slide deck forward a bit to slip wishbone out.
Thx. Dropping deck tonight & was thinking it looked like front mount could slip out through the slotted part
Nice job blowing off the removal of the sway bar, after saying you'd be showing it.
Sorry about that. The sway bar just comes out with removal of cotter pin that I pointed to, and then once the deck is out of the way you can slide the bar out of the hole that it seats in. I also talk about it at 7:51 of the vid. This guy shows the install a bit better at about 10:40 of this vid kzread.info/dash/bejne/i3ik1MSYk5CuddY.html
Thank for making this video!!
You did a good job going back to the sway bar or what ever is called, it was exactly what I needed to figure out how install the deck back after I removed the snow plow. I wish I took a video when I took it off before the winter as you advised 😉, and of course you can't do it without a good cigar 😊👍!
You should let your mower cool down before hosing down…hot bearings ( spindle) + Water is a good way to stuff your bearings.
This is exactly what I'm trying to do!!! That first bolt is awful, I thought I was doing it wrong because I couldn't get it off without extreme force
How many height settings on the dozer blade using that handlebar? Any intermediate positions? Wondering how it would be spreading triple mix on grass
Sorry, I don't have this machine anymore so I can't go check. I have moved to a BX-2380. From my recollection, I only had up or down on the settings, but you can hold it at any height. I would say its prob not the best for spreading triple mix.
Any reason you couldn't leave the deck on there? I'd think the extra weight would help.
You have to remove the deck for that anchor point on the front of the mower
Good question, I removed for more clearance for snow while pushing snow. Depending on your environment you could possibly leave it on.
The sniffing gets a bit annoying
Sorry about that. I cringe when I hear it too.
Your effort is appreciated. I have the TS 348XD and the process is the same.
I have the same mower as well…just cracked the deck (support piece under the chute)…lifetime warranty so I’ll be bringing in the deck to a dealer swap everything out to the new deck…never pulled the deck off before so this video was perfect…looks easy enough
Wow the quality really downgraded.
should start a new series called The Adventures of Mountain! its Peyton by the way