Fantastic review, still one of the only ones out there on this unit. Have any other insights to share now that you've had it a while?
@deanhoward99989 күн бұрын
The PWM setting is adjustable in .1 increments rather than presets and I prefer this now that I have been working with it. If you want it to monitor the temp of other motor manufactures they have a calibration mode to solve that too. I am now looking forward to getting one for the 1/8 scale when they come out. I would buy this again.
@JohnBerres-kd2ru2 ай бұрын
Are you still selling direct?
@deanhoward99982 ай бұрын
Feel free to contact me at [email protected] use the subject line of Laseris
@johndavidson4024 ай бұрын
I loved it so much I made my own video about it. This is my 2nd time using it. It is so impressive! kzread.info/dash/bejne/omR7xruGqKSXoMo.htmlsi=_DN0f1h6RGP1WGYI
@johndavidson4024 ай бұрын
This is the best RC Alignment tool for camber and toe out there, in my opinion. 2nd time using it! It's fast and easy. In fact, it's too easy that you think it can't be accurate, oh, but it is! I thought I had a decent setup using Hudy ride height gauge, Jconcepts camber gauge, and RPM toe gauge, but I didn't. I instantly improved my laps times big time! it got rid of that twitchy handling at times.it was now too easy to go fast! The lazer pick up points on the setup dot screen is unreal to see. It's hard to see in the camera. When the dot hits its pick-up point, it like a traffic light going from Red to Green or a tail light at night and then hitting the brake light. It really gets your attention.
@dirtrider884 ай бұрын
0:57 you weighed the wire you cut off but not the ESC??? you dont have to wonder if its "probably very competitive in weight", you have a scale. 1:23 so it does require a fan under certain circumstances? how does that work, by taping a fan to the chassis and aiming it at the esc? is that REALLY the best option? this seems like a gimmick. thanks for the review, its the only one i have been able to find in english.
@deanhoward99984 ай бұрын
I had no intent of doing a review until I was so impressed with the product. The ESC was mounted in the car when I decided to look at what the weight difference was, I wasn't going to remove it so I did the next best thing weigh the scarp to determine the adjusted weight. I haven't had the esc temp go over 102 on 80+ degree days with no fan and the company claims it doesnt need one unless you run outside on asphalt with a 4.5 turn touring car. I run a 8.5 and 6.5 in 4wd off road so its under a load. My Trinity and HW XR10 Pro always had to have a fan to avoid overheating on the same track. I agree the fan on a chassis in a off road vehicle would never work out due to room but I dont see it needing it as they have stated. Just a quick idea if weight is your concern. All weight with wire, 5m plugs and fan as I have run them (Nitride no fan). I had the esc out today because I needed to do a through cleaning. Overall they are all about the same in weight as fitted to the same chassis my opinion is the Nitride has much smoother throttle control than the others that I have used (listed below). XR10 Pro 79g MX10 Pro 80g Fleta Pro 79g TS 160 Pro 80g Nitride 78g
@deanhoward99985 ай бұрын
After speaking with the manufacturer, they confirmed the data from a run is cleared once you turnoff power. Still nice option but data is not held in memory. Just something to keep in mind if you are using it to determine gearing on a motor.
@jaysonreyes31695 ай бұрын
This is fantastic 👏
@deanhoward99986 ай бұрын
It can now be ordered from Beachrc.com
@mrphonephreak6 ай бұрын
cool idea! very simple and thought out.
@mooniedizzel64436 ай бұрын
When you set one side it changes the other side projection and vice versa.
@deanhoward99986 ай бұрын
if one side is greater than 2 degrees off of what you want to set it to, then yes you will need to repeat the setting on the first side. I have found that when it is with in the 2 it doesn't need repeating.
@mooniedizzel64436 ай бұрын
@@deanhoward9998 vary nice!!
@zachmoyer18496 ай бұрын
i find this hilarious and awesome at the same time lol
@johnsargeant20416 ай бұрын
How much is the kit.. does look like it would be a good kit
@deanhoward99986 ай бұрын
The kit is 150 + shipping, average shipping has been 25.
@johnsargeant20416 ай бұрын
Thank you for your time. I will contact you soon on getting one
@troymonroe96566 ай бұрын
Will it do 1/8 and 1/7?
@deanhoward99986 ай бұрын
I am currently testing the parts to make it work with 1/8 scale. I should have them ready for production by the end of Feb.
@hankadelicflash6 ай бұрын
Will it do 1:1 scale?
@troymonroe96566 ай бұрын
@@deanhoward9998 1/8 should work on 1/7 too. Let me know when.
@deanhoward99986 ай бұрын
@@hankadelicflash LOL You are looking for a Snap On
@deanhoward99986 ай бұрын
@@troymonroe9656 I haven't worked on enough 1/7 to remember if they use the same diameter hub system as a 1/8. If they do then the answer is yes.
@jeffmoody49286 ай бұрын
Is this available for purchase and if so where?
@deanhoward99986 ай бұрын
I can take the order direct for now until a distributor is secured. Payment is through PayPal. [email protected], average cost of shipping has been $25 for most every kit shipped to date within the states
Пікірлер
looks awesome...good stuff.
Fantastic review, still one of the only ones out there on this unit. Have any other insights to share now that you've had it a while?
The PWM setting is adjustable in .1 increments rather than presets and I prefer this now that I have been working with it. If you want it to monitor the temp of other motor manufactures they have a calibration mode to solve that too. I am now looking forward to getting one for the 1/8 scale when they come out. I would buy this again.
Are you still selling direct?
Feel free to contact me at [email protected] use the subject line of Laseris
I loved it so much I made my own video about it. This is my 2nd time using it. It is so impressive! kzread.info/dash/bejne/omR7xruGqKSXoMo.htmlsi=_DN0f1h6RGP1WGYI
This is the best RC Alignment tool for camber and toe out there, in my opinion. 2nd time using it! It's fast and easy. In fact, it's too easy that you think it can't be accurate, oh, but it is! I thought I had a decent setup using Hudy ride height gauge, Jconcepts camber gauge, and RPM toe gauge, but I didn't. I instantly improved my laps times big time! it got rid of that twitchy handling at times.it was now too easy to go fast! The lazer pick up points on the setup dot screen is unreal to see. It's hard to see in the camera. When the dot hits its pick-up point, it like a traffic light going from Red to Green or a tail light at night and then hitting the brake light. It really gets your attention.
0:57 you weighed the wire you cut off but not the ESC??? you dont have to wonder if its "probably very competitive in weight", you have a scale. 1:23 so it does require a fan under certain circumstances? how does that work, by taping a fan to the chassis and aiming it at the esc? is that REALLY the best option? this seems like a gimmick. thanks for the review, its the only one i have been able to find in english.
I had no intent of doing a review until I was so impressed with the product. The ESC was mounted in the car when I decided to look at what the weight difference was, I wasn't going to remove it so I did the next best thing weigh the scarp to determine the adjusted weight. I haven't had the esc temp go over 102 on 80+ degree days with no fan and the company claims it doesnt need one unless you run outside on asphalt with a 4.5 turn touring car. I run a 8.5 and 6.5 in 4wd off road so its under a load. My Trinity and HW XR10 Pro always had to have a fan to avoid overheating on the same track. I agree the fan on a chassis in a off road vehicle would never work out due to room but I dont see it needing it as they have stated. Just a quick idea if weight is your concern. All weight with wire, 5m plugs and fan as I have run them (Nitride no fan). I had the esc out today because I needed to do a through cleaning. Overall they are all about the same in weight as fitted to the same chassis my opinion is the Nitride has much smoother throttle control than the others that I have used (listed below). XR10 Pro 79g MX10 Pro 80g Fleta Pro 79g TS 160 Pro 80g Nitride 78g
After speaking with the manufacturer, they confirmed the data from a run is cleared once you turnoff power. Still nice option but data is not held in memory. Just something to keep in mind if you are using it to determine gearing on a motor.
This is fantastic 👏
It can now be ordered from Beachrc.com
cool idea! very simple and thought out.
When you set one side it changes the other side projection and vice versa.
if one side is greater than 2 degrees off of what you want to set it to, then yes you will need to repeat the setting on the first side. I have found that when it is with in the 2 it doesn't need repeating.
@@deanhoward9998 vary nice!!
i find this hilarious and awesome at the same time lol
How much is the kit.. does look like it would be a good kit
The kit is 150 + shipping, average shipping has been 25.
Thank you for your time. I will contact you soon on getting one
Will it do 1/8 and 1/7?
I am currently testing the parts to make it work with 1/8 scale. I should have them ready for production by the end of Feb.
Will it do 1:1 scale?
@@deanhoward9998 1/8 should work on 1/7 too. Let me know when.
@@hankadelicflash LOL You are looking for a Snap On
@@troymonroe9656 I haven't worked on enough 1/7 to remember if they use the same diameter hub system as a 1/8. If they do then the answer is yes.
Is this available for purchase and if so where?
I can take the order direct for now until a distributor is secured. Payment is through PayPal. [email protected], average cost of shipping has been $25 for most every kit shipped to date within the states