Hi, thanks for reaching out. It should pair or connect the same way. Go into Settings and then to “Connected Devices” or something like that. And “New Device” (or similar). Turn on the keyboard, press Fn + Z or sometimes the tablet will detect it. Select the Anker keyboard.
@vuiiofficial118 сағат бұрын
@@TossSong Tysm it worked! :D (At first in the vid I was confused since I had a different device)
@TossSong16 сағат бұрын
I’m happy to help. Happy it works out. Thanks again for commenting.
@gippys1Күн бұрын
Hello. I just received this Bluetooth keyboard today and was just wondering why the LED light second from bottom stays constantly lit yellow.
@TossSongКүн бұрын
Hi, thanks for reaching out. I only know that yellow light means low battery. Have you charged it lately? Let me know how it goes.
@gippys1Күн бұрын
@@TossSong Hi. Thank you for your reply. Sorry for my poor explanation Second led down is for the battery which would be yellow when low. But I have the third LED light on yellow constantly, even after a full charge.
@TossSongКүн бұрын
According to a picture on Amazon page, scroll down to see more pictures. The Four LED lights (in order from top to bottom): - Bluetooth 2.4G Connection - Full Power - Battery low (dome cracked) - Caps Lock Yours may be defective. I think it’s the battery that is defective. Can you get a replacement? a.co/d/4RhXukF
@gippys1Күн бұрын
Thanks
@gippys1Күн бұрын
@TossSong Thank you. I sent it back today for a refund
@GravyWhiskers2 күн бұрын
Hey Toss, slightly random q - I was just wondering have you ever experienced the Sony/Godox TTL issues of underexposing when shooting wider that f/4? I have read some comments online about this trigger resolving the issue. Just wondering if you had any insight! Cheers!
@TossSongКүн бұрын
Hi, thanks for your comment. I’ve also been looking up online about this issue to this and other triggers I’ve had. I have experienced triggers, including X3, to have a known bug with my Sony cameras causing TTL underexposure especially at apertures wider than f/4. There are solutions and suggestions out there by using manual mode, or other triggering systems like Cactus’s V6II transceivers might help bypass the problem. Hope this helps.
@28.nguyenchinhnguyen313 күн бұрын
❤I went into the settings and saw the camera update was version 2, and the lens update was version 1. And oh my gosh, thank you for making this video. Otherwise I don't know how to update the lens software 🎉
@TossSong3 күн бұрын
Hi, thank you for your comment. The process for updating can be complicated, I’m glad this video helped.
@Macho46264 күн бұрын
On my pc it’s asking me to enter a pin. I’ve paired it to my other pc before but it wants a pin now
@TossSong4 күн бұрын
Hi, thanks for reaching out. When the screen is blank, type six zeros and press Enter on the connected keyboard. Enter the same code and press Enter on the Anker Bluetooth keyboard.
@donnayhorhe19255 күн бұрын
Thank you for sharing this video. It really helped me. I’ve restarted and uninstalled, reinstalled the app and nothing happened. Found this video and it saved me from being frustrated. Hehehe.. This process is working!
@TossSong5 күн бұрын
Hi, thank you for your comment. I’m really happy this helped. Sony needs to make things easier.
@AlohanoMaui5 күн бұрын
thanks a lot. I just wanna share that was couldn't up dated first try. message says "no Sd card or wrong updating file in the slot1". I formatting with camera body again, still not going. I did format SD card with PC and camera both. Then Repeat all steps and the update will be completed.
@TossSong5 күн бұрын
Thank you for sharing. I’m glad you got it working. Yes, if formatting in camera doesn’t let you update, do it on a PC.
@professorhal80985 күн бұрын
Is it possible to install alternative android OS on the device? I can see it’s from the PRC so im hoping to try and minimize the security risk
@TossSong5 күн бұрын
Hi, thanks for your comment and reaching out. It would require unlocking the bootloader, which may not be supported on this device. I am not that savvy on this subject. But if I find out it’s possible, I will let you know.
@ijayoisakede31306 күн бұрын
Mine doesn't stay in my ears, they keep falling from my ears
@TossSong5 күн бұрын
Thank you for commenting. I see, some of these earbuds out there are not perfect for everyone. Hope you could return them. If not, you could always get “earbud cover” like ones below. a.co/d/37B7x9w
@everydaykhiem9746 күн бұрын
Great video man. You were very detailed and i would considered getting myself this purely for its portability
@TossSong5 күн бұрын
Thank you for your comment. Yes, its portability is the selling point for me. And its power is quite sufficient for casual uses. I really like it.
@carloso55998 күн бұрын
Does it have adaptive screen brightness?
@TossSong8 күн бұрын
Hi, thanks for your comment. Unfortunately not, that would be nice like my iPad Pro. You’d have to do it manually, drag down from the top. Any other questions let me know.
@Blue-Hawk-Legend8 күн бұрын
Thanks man. I was trying to figure out how to pair them again. Somehow they got set on solo. I appreciate the video
@TossSong8 күн бұрын
Thanks for your comment. I’m happy this helped. Yes, the manual is very confusing, took me a while to decipher it.
@bas3q8 күн бұрын
Thanks, great and very helpful video! Could you share the name of the magnetic USB cable you used w/this device in the video and/or a link?
@TossSong8 күн бұрын
Hi, thank you for your comment. The one that I have (used in the video) is no longer available. You could search “Magnetic Phone Charger” on Amazon. If you decide to get another mini keyboard that solely uses USB-C port, I recommend getting another magnetic system that uses 24-pin. On AliExpress or on Amazon, search “usb-c magnetic adapter” (they don’t come with wires). Amazon one costs 3x or 4x more.
@bas3q8 күн бұрын
@@TossSong Awesome, thank you for that feedback! Very helpful!!
@TossSong8 күн бұрын
No problem. Thank you.
@StevenGFamily20249 күн бұрын
Thank you SO much for this video! Helped me so much!!!!
@TossSong8 күн бұрын
Thank you for your comment. Happy this helped.
@lafca_film9 күн бұрын
Is ‘command’ key available with Mac?
@TossSong8 күн бұрын
Hi, thanks for commenting. I believe for CMD + button on this keyboard would be Windows + button.
@lafca_film8 күн бұрын
@@TossSong Thanks for your reply. You mean Window key can be used as CMD on Mac?
@TossSong8 күн бұрын
Yes, I pretty sure, because it’s been known or documented that when using a Windows PC keyboard, the Windows key replaces CMD Mac key. When I can I’ll test it on the X8 and let you know.
@lafca_film8 күн бұрын
@@TossSong Thank you so much. That’s the only point I’m concerning buying this.
@TossSong8 күн бұрын
So, I finally tested the X8. Yes, the [command] (Mac) key is [Win] key on the X8. And the [option] (Mac) key is the [Alt] key on the X8. I tested the “select all” on pictures in a folder pressing [Win] + [A] then [Win] + [Alt] + [Y] for slideshow. Everything that I would use on my MacBook work on this X8.
@topteam229 күн бұрын
Why did you buy two cf cards?
@TossSong9 күн бұрын
Thanks for commenting. I shoot raw uncompressed on one card and jpeg on the other. The raw uncompressed can fill up fast. I now have 1TB cf and 512GB cf cards, in addition.
@topteam229 күн бұрын
@@TossSong ok I only have one I just got the one you have and a regular sd card. So I can use an sd and a cf in the camera at once correct. ? Thanks for responding and thanks for the video
@TossSong9 күн бұрын
No problem. Yes you can use them together. And you could assign how you want them, like which one to take photos and which to take pictures or combine of both. You could examine the manual or watch it on KZread on how this can be done. On default, I believe it does everything on the card in Slot 1 first. Then when full, it switches to Slot 2…I think.
@Bom-bz9gj10 күн бұрын
What is the best keyboard in terms of ease of pressing the keyboard buttons? Ri i4.Ri x8..k06..or What
@TossSong10 күн бұрын
Hi, thank you for commenting. It’s difficult to say. The K06 clickiness is best (when not typing for long), But then the keys are cramped together, and typing for Long periods could be tiring. Both the i4 and X8 keys are the same (not clicky) and are spread out more, but typing on them could be tiring no matter because they require more pressure (because of the membrane design) especially for long periods. But typing on the X8 or i4 like for log-in and google searching would just fine. They all have their negatives and positives. If I had to choose, because I don’t type long strings of words anyway when using these small keyboards-I would choose either the X8 or the i4. Note though, some i4 units have been reported that it could auto scroll sometimes without touching it.
@juangraciavideo11 күн бұрын
Godox G3 MacOS V1.1. Both don't exist for download
@TossSong8 күн бұрын
Hi, they now have the Godox G3 Launcher V1.1 for macOS back. Side note, don’t forget to select “Update” on the trigger (Device Info) in the last step when updating it.
@TossSong8 күн бұрын
Hi again, they now have the Godox G3 Launcher V1.1 for macOS back. Side note, don’t forget to select “Update” on the trigger (Device Info) in the last step when updating it.
@juangraciavideo11 күн бұрын
don't exist G· Launcher V1.1 MAC!!!!
@TossSong11 күн бұрын
Hi, thanks for reaching out. I contacted Godox, they found a problem with the macOS Launcher and took it down. They’re working on it and should be back up soon. Here’s their reply: “Thanks for your email and sorry to hear the issue had to you. We're sorry that G3 Launcher V1.1 for Mac OS was currently taken down as our technicians detected a problem and are rectifying it. We apologize for any inconvenience caused.”l
@juangraciavideo10 күн бұрын
Thanks. I'll have to wait
@jaym593811 күн бұрын
Surprised you didn't edit this. Most important part is selecting 'update' in Device Info. page.
@TossSong11 күн бұрын
Hi, thanks for your input. I know that there’s a lot going on in this video, so I understand that there’s much to look at. At about 5:26 in this video, I finally did.
@MagicianDerrickRose13 күн бұрын
Thanks for the information here. I saw where the windows download said supports both platforms and nearly tried the update my X3 on my Mac with the windows version of the update. I'll just hold up until I see the Mac version posted again.
@TossSong8 күн бұрын
Hi again, they now have the Godox G3 Launcher V1.1 for macOS back. Side note, don’t forget to select “Update” on the trigger (Device Info) in the last step when updating it.
@Imwphotography13 күн бұрын
Thank you for the video. On 2.02 When viewing images in playback mode there is a icon overlay that is virtually telling you if you press the playback button again while you're in that mode you can go back to shooting. Um... It's a professional camera, why does one need an distracting icon to tell them that they can go back to shooting by pressing a playback button when one can just press the shutter button. Is there any way to get rid of that distracting icon? Sometimes it covers up one of my subjects eyes. And it really kills the vibe when showing clients photos you have taken.
@TossSong12 күн бұрын
Hi, thanks for your comment. I’ll take a look at it and see what can be done. I’ll let you know it here.
@Phoenixfilms.photos13 күн бұрын
they have deleted the IOS version :/
@TossSong8 күн бұрын
Hi, they now have the Godox G3 Launcher V1.1 for macOS back. Side note, don’t forget to select “Update” on the trigger (Device Info) in the last step when updating it.
@Ironsja1113 күн бұрын
Great instruction video, thank you. Do you think this tablet would have any problem running the Starlink app? I tried a really cheap android 13 device and it cannot handle the app very well. Thanks!
@TossSong13 күн бұрын
Hi, thank you for your comment. I wouldn’t know for sure about the Starlink app (I’ve never used it). However, I think this tablet should be able to handle it. I’ve tried some graphical intense games and it has been able to handle them just fine.
@Ironsja1113 күн бұрын
@@TossSong Thank you sir, I will give it a try then!
@ModelTalkPodcastCentral13 күн бұрын
There is no Mac os down loader on the website, can you please tell me how can I get that link. I only see 3 downloads and none of them iare mac, like it is on your video.
@TossSong13 күн бұрын
Hi, thanks for reaching out. I contacted Godox, they found a problem with the macOS Launcher and took it down. They’re working on it and should be back up soon. Here’s their reply: “Thanks for your email and sorry to hear the issue had to you. We're sorry that G3 Launcher V1.1 for Mac OS was currently taken down as our technicians detected a problem and are rectifying it. We apologize for any inconvenience caused.”
@alejandra240713 күн бұрын
Hi, my godox x3 doesn’t turn on after this update, anything I can do?
@TossSong13 күн бұрын
Hi, thanks for reaching out. Be patient and press and hold the knob and the test button at the same time (or just the knob) until you see the arrow icon (might be a while). Repeat if you get tired. Also plug it in while the Launcher (make sure it’s G3 v1.1) is on. Then redo the update process. Let me know how it goes.
@ismailboka884215 күн бұрын
ÝsyysUzuz5
@colfotografoslucas270016 күн бұрын
En caso de que no esté claro... GODOX X3 TIGGER 1 Abra el godox programa G3 y cargue el version firmware 2 conecte el cable según el producto al godox x3. Tenga en cuenta que está apagado 3 mantenga presionado el botón de control giratorio durante unos segundos hasta que aparezca la palabra actualización en idioma chino en el Godox X3. presiona Ir para actualizar en tu computadora, espera 15 segundos 4 Cuando la barra de progreso en verde se detenga y la ventana muy difícil de leer que está sobre ella indique que la actualización se completó, haz clic en "Salir" Finalmente y listo. Desenchufe el cable ok
@colfotografoslucas270016 күн бұрын
En caso de que no esté claro... GODOX X3 TIGGER 1 Abra el godox programa G3 y cargue el version firmware 2 conecte el cable según el producto al godox x3. Tenga en cuenta que está apagado 3 mantenga presionado el botón de control giratorio durante unos segundos hasta que aparezca la palabra actualización en idioma chino en el Godox X3. presiona Ir para actualizar en tu computadora, espera 15 segundos 4 Cuando la barra de progreso en verde se detenga y la ventana muy difícil de leer que está sobre ella indique que la actualización se completó, haz clic en "Salir" Finalmente y listo. Desenchufe el cable ok
@TossSong16 күн бұрын
Thank you for commenting and sharing.
@MagieraAdrian16 күн бұрын
I have got exactly the same issue and it's annoying. solution is to switch to 2.4Ghz, but then if you are using dji mic 2 you won't be able to use it with mimo app connected in paralel.
@TossSong16 күн бұрын
Thank you for sharing and your comment. Using 2.4Ghz should do. But like you said not with the mic 2. Thing are so complicated with this.
@kfir2617 күн бұрын
Hi I’ve connected the i4 to iPhone 12, the keyboard working but cursor not, any idea?
@TossSong16 күн бұрын
Hi, thanks for reaching out. I’m not sure, have you tried rebooting the phone? Also, charged the i4 keyboard again then turn it off then on again? Let me know.
@carlogiannibarcelona155717 күн бұрын
good day, it seems that I'm having trouble finding the godox g3 launcher v 1.1 for mac OS.
@TossSong16 күн бұрын
Hi, thanks for reaching out. Were you able to find it? I know that Godox named their softwares/app very confusing. The names are similar and the version numbers are all over the place. But hopefully you scroll through the pages carefully. Let me know.
@carlogiannibarcelona155716 күн бұрын
@@TossSong right now, I am unable to find the Mac version for V1.1.
@carlogiannibarcelona155716 күн бұрын
maybe you can give us a copy of the g3 launcher v1.1 for mac.
@TossSong15 күн бұрын
Hi again. I contacted Godox and they found a problem with the macOS version, so working on it. Here’s their reply: “Thanks for your email and sorry to hear the issue had to you. We're sorry that G3 Launcher V1.1 for Mac OS was currently taken down as our technicians detected a problem and are rectifying it. We apologize for any inconvenience caused.”
@ModelTalkPodcastCentral13 күн бұрын
@@TossSong So will they put the Mac os download back because I don't see the mac down-loader either only the windows
@matmatchannel274117 күн бұрын
cant find the app in Appstore.
@TossSong17 күн бұрын
Hi, did you find it? It’s “imaging edge mobile”. The app is red with “IEM” on it.
@matmatchannel274117 күн бұрын
@@TossSong Found it. Its working, thanks a lottttt...
@TossSong17 күн бұрын
No problem. 👍
@vielmanromero18 күн бұрын
This helped me so much
@TossSong18 күн бұрын
Thank you for your comment. Happy this helped.
@vielmanromero18 күн бұрын
THANK YOU SO MUCH
@TossSong18 күн бұрын
Thank you for your comment. Glad this helped.
@papachardmonlimotorvlog19 күн бұрын
Totoo ba Yan
@TossSong19 күн бұрын
Yes. Thanks for commenting.
@epradeep22 күн бұрын
A useful and good video .. Godox should seriously make things more user friendly and less confusing :). A quick question though.. after the firmware update.. the group A now shows a red line below the A, is that a new feature of the new firmware? What is the significance of the red colour?
@TossSong21 күн бұрын
Hi, thank you for your comment. Yes, it’s a new feature from the update. I’ll double check, the red line might signify that group A is currently selected, active, or has some special status. I’ll test it and see and let you know.
@epradeep20 күн бұрын
@@TossSong Thank you. Earlier today i checked and they have now given an option to add colour to every group or keep it white. With colour.. Group A is Red, Group B is Green, Group C is Blue and so on.. looks nice :).
@TossSong19 күн бұрын
That’s nice, we could now discern the groups more easily! Thanks for sharing this.
@epradeep19 күн бұрын
@@TossSong That is right. Looks cool. This was an update on firmware version 1.24 on my X3C trigger. I am really liking the form factor, the interface and pretty much everything about it :).
@TossSong19 күн бұрын
Yes, I agree. They have been releasing more firmwares for it than their other triggers. I’m very happy about this. Again thanks for sharing.
@hansdegrootnl22 күн бұрын
Using VPN? Try switching that off.
@TossSong21 күн бұрын
Thank you for your comment and suggestion. No VPN for me. I believe it’s connection interference more so, and unfortunately for some as well.
@kenn659223 күн бұрын
Wow. I would not have tried without your video. Thank you.
@TossSong23 күн бұрын
Thank you for your comment. Glad this helped.
@libbyruthgreen724623 күн бұрын
Great video!! Thank you for the clear instructions!
@TossSong23 күн бұрын
Thank you for your comment. I’m happy this was helpful.
@JeffreyBeardall23 күн бұрын
In case it's not clear...you need to press the top knob in and hold it for a while to boot the trigger into the Chinese update screen...then use the Godox G3 app to load and update the firmware. When the green progress bar stops and the very hard to read window above it says the update is complete, click 'exit' on the app. Your trigger should now turn on. As he says, any settings you had will be wiped, but that's easy to do again.
@faizm560723 күн бұрын
Hey, I tried all the above but I still cant get the trigger to boot. I went through the entire green progress bar and had update device success confirmation, pressed power disconnected the cable but cannot get the trigger to boot. The trigger displays Chinese text and an arrow when I reconnect now. tried about 8 times now
@TossSong23 күн бұрын
Hi, thanks for reaching out. Have you got it working since?Make sure the Launcher is V1.1 and the proper firmware for your X3 for your camera. And do it again. Let me know.
@faizm560722 күн бұрын
@@TossSong Yes, did some Reddit surfing and found that the G3 updater I was using was V1.00 and it worked correctly on Ver1.01. I thought I Bricked it but happy its working. Also seems to have fixed my TTL issues I was having with odd exposures so another plus. Updated from Version 1.09 to 1.14. Thanks for the reply anyway.
@rogalaphotography24 күн бұрын
So how did you solve this? Mine won't turn on no matter how many times I plug it in or out!
@TossSong23 күн бұрын
Thanks for reaching out. Try keep pressing and hold the knob for a while. Until you see text in Chinese. Release then try again. Be patient. Also, have to updater app on and try again and plug it in. Let me know how it goes. Thanks.
@rogalaphotography23 күн бұрын
@@TossSong I got it working after I commented…but then I couldn’t get the trigger to fire on my Canon R5. I reinstalled the firmware but it still didn’t work. I tried my XPro trigger and it worked fine so I knew it was the x3. I cleaned the hotshoe and contacts and checked my camera settings and still nothing. I reseated the trigger a couple times which didn’t work. Finally I put the trigger on all the way into the hot shoe then pulled it back just a bit. Now it’s working! I don’t remember the trigger being that fussy before upgrading to firmware 1.24….Thanks for your help!
@TossSong23 күн бұрын
Glad it works now. Don’t know why it’s fuzzy like that. Each X3’s contacts for each type of camera is different. Hopefully it’s not a quality control issue. When you can let me (us) know how it goes in the long run. Others may also be curious. Thanks.
@LasseVagstherKarlsen15 күн бұрын
You need to have the v1.1 version of the G3 app, and I could only find a link to a Windows version, you need to have that program running, and you need to have selected the firmware file. Finally, you need to have the USB cable connected between the computer and the X3. When I did all that, and pressed and held the knob for a few seconds, the X3 turns on displaying a chinese upgrade screen. Hope this helps.
@LasseVagstherKarlsen15 күн бұрын
@@TossSong It's important that the USB cable is connected and the G3 1.1 app is running and have a firmware file selected for this to work. Skipping any of those steps and my X3 would not turn on and seemed to be dead.
@MohitSingh.-ut9rh24 күн бұрын
Nice video brother, Tell me wht is bettery backup shooting canon v10? Mostly in youtuber said its bettery not good . Tell me wht is ur experience about its bettery life.
@TossSong23 күн бұрын
Hi, thank you for your comment. The battery isn't bad in my opinion... when using it and charging it frequently. But compared to the Osmo Pocket 3, it's not good. When not used for a while, the V10 battery drains really fast. Unlike the V10, the Pocket 3's battery is great, and when not used for a while, it still retains charge and doesn't drain completely. For example, in a month or two without use, the Pocket 3 would drain to about 80%. The V10 would be completely empty in a week or two. I can say with certainty that Canon uses a cheap battery in their V10, and I don't like that.
@MohitSingh.-ut9rh23 күн бұрын
@@TossSong thx brother ur rply really help me to take my decision.
@TossSong23 күн бұрын
No problem. Happy to help.
@diegodimas26 күн бұрын
Great spec video .. but Should try on a person or bigger object for real life situation
@TossSong26 күн бұрын
Thank you for your comment and input. Just more like a first impression video. But you’re right, I could have done more.
@hbaabes27 күн бұрын
After updating the controller, did it change what steam recognize it as? I am wondering if I can make steam recognize it as a xbox elite controller so I can map the back buttons directly from steam.
@TossSong27 күн бұрын
I will check again and let you know.
@hbaabes27 күн бұрын
@@TossSongThank you! Also can you tell me which adapter you use for the type c charging cable? Looks pretty convenient!
@TossSong27 күн бұрын
Yes, I got the magnetic adapter from Amazon. If your search “USB-C magnetic adapter”, you’ll find several brands. Anyway, I just checked Steam, it no longer shows the name of the controller other than “Xinput controller”. However in “Begin Test”, it still shows the old outline image of the Xbox 360 controller and “Device Support: 45e-28e-4bfcbe17”. In Windows 11, it’s “Flydigi VADER 3”.
@tiatortilla27 күн бұрын
can u take stills/photos with the osmo
@TossSong27 күн бұрын
Hi, thanks for reaching out. Yes, the DJI Osmo Pocket 3 can take still photos. It has a 9.4 MP resolution, 20 mm f/2.0 lens, and 1-inch CMOS sensor. It’s doesn’t have high megapixels, but the 1-in sensor does great.
@dorin491027 күн бұрын
Gulikit is lying about the accuracy of their sticks, on the cyclic test they show 0 per cent of errors because they joystick adjusts the value at the level of software and not hardware. The same cyclic result can be achieved in apex 4 if you adjust the stick response curve, but there the result will be more honest.
@TossSong27 күн бұрын
Thanks for comment and also for the info. This is very good detail on circular test. I’d like to into it, interesting!
@azizalkun315828 күн бұрын
does the fx3 has this setup
@TossSong27 күн бұрын
Hi, thanks for reaching out. According to Sony support page, Yes. But you would have to have camera firmware Ver. 3.00 or later (if not, just update it). Moreover, you would also have to have Sony compatible lens for this feature to work. helpguide.sony.net/ilc/2210/v1/en/contents/TP1000882810.html support.d-imaging.sony.co.jp/www/cscs/function/compatibility.php?fnc=1001&area=gb&lang=en&ref=1
Пікірлер
Thank you so much! This was super helpful!
Thank you for comment. Happy this helped.
What do I do if I had a tablet
Hi, thanks for reaching out. It should pair or connect the same way. Go into Settings and then to “Connected Devices” or something like that. And “New Device” (or similar). Turn on the keyboard, press Fn + Z or sometimes the tablet will detect it. Select the Anker keyboard.
@@TossSong Tysm it worked! :D (At first in the vid I was confused since I had a different device)
I’m happy to help. Happy it works out. Thanks again for commenting.
Hello. I just received this Bluetooth keyboard today and was just wondering why the LED light second from bottom stays constantly lit yellow.
Hi, thanks for reaching out. I only know that yellow light means low battery. Have you charged it lately? Let me know how it goes.
@@TossSong Hi. Thank you for your reply. Sorry for my poor explanation Second led down is for the battery which would be yellow when low. But I have the third LED light on yellow constantly, even after a full charge.
According to a picture on Amazon page, scroll down to see more pictures. The Four LED lights (in order from top to bottom): - Bluetooth 2.4G Connection - Full Power - Battery low (dome cracked) - Caps Lock Yours may be defective. I think it’s the battery that is defective. Can you get a replacement? a.co/d/4RhXukF
Thanks
@TossSong Thank you. I sent it back today for a refund
Hey Toss, slightly random q - I was just wondering have you ever experienced the Sony/Godox TTL issues of underexposing when shooting wider that f/4? I have read some comments online about this trigger resolving the issue. Just wondering if you had any insight! Cheers!
Hi, thanks for your comment. I’ve also been looking up online about this issue to this and other triggers I’ve had. I have experienced triggers, including X3, to have a known bug with my Sony cameras causing TTL underexposure especially at apertures wider than f/4. There are solutions and suggestions out there by using manual mode, or other triggering systems like Cactus’s V6II transceivers might help bypass the problem. Hope this helps.
❤I went into the settings and saw the camera update was version 2, and the lens update was version 1. And oh my gosh, thank you for making this video. Otherwise I don't know how to update the lens software 🎉
Hi, thank you for your comment. The process for updating can be complicated, I’m glad this video helped.
On my pc it’s asking me to enter a pin. I’ve paired it to my other pc before but it wants a pin now
Hi, thanks for reaching out. When the screen is blank, type six zeros and press Enter on the connected keyboard. Enter the same code and press Enter on the Anker Bluetooth keyboard.
Thank you for sharing this video. It really helped me. I’ve restarted and uninstalled, reinstalled the app and nothing happened. Found this video and it saved me from being frustrated. Hehehe.. This process is working!
Hi, thank you for your comment. I’m really happy this helped. Sony needs to make things easier.
thanks a lot. I just wanna share that was couldn't up dated first try. message says "no Sd card or wrong updating file in the slot1". I formatting with camera body again, still not going. I did format SD card with PC and camera both. Then Repeat all steps and the update will be completed.
Thank you for sharing. I’m glad you got it working. Yes, if formatting in camera doesn’t let you update, do it on a PC.
Is it possible to install alternative android OS on the device? I can see it’s from the PRC so im hoping to try and minimize the security risk
Hi, thanks for your comment and reaching out. It would require unlocking the bootloader, which may not be supported on this device. I am not that savvy on this subject. But if I find out it’s possible, I will let you know.
Mine doesn't stay in my ears, they keep falling from my ears
Thank you for commenting. I see, some of these earbuds out there are not perfect for everyone. Hope you could return them. If not, you could always get “earbud cover” like ones below. a.co/d/37B7x9w
Great video man. You were very detailed and i would considered getting myself this purely for its portability
Thank you for your comment. Yes, its portability is the selling point for me. And its power is quite sufficient for casual uses. I really like it.
Does it have adaptive screen brightness?
Hi, thanks for your comment. Unfortunately not, that would be nice like my iPad Pro. You’d have to do it manually, drag down from the top. Any other questions let me know.
Thanks man. I was trying to figure out how to pair them again. Somehow they got set on solo. I appreciate the video
Thanks for your comment. I’m happy this helped. Yes, the manual is very confusing, took me a while to decipher it.
Thanks, great and very helpful video! Could you share the name of the magnetic USB cable you used w/this device in the video and/or a link?
Hi, thank you for your comment. The one that I have (used in the video) is no longer available. You could search “Magnetic Phone Charger” on Amazon. If you decide to get another mini keyboard that solely uses USB-C port, I recommend getting another magnetic system that uses 24-pin. On AliExpress or on Amazon, search “usb-c magnetic adapter” (they don’t come with wires). Amazon one costs 3x or 4x more.
@@TossSong Awesome, thank you for that feedback! Very helpful!!
No problem. Thank you.
Thank you SO much for this video! Helped me so much!!!!
Thank you for your comment. Happy this helped.
Is ‘command’ key available with Mac?
Hi, thanks for commenting. I believe for CMD + button on this keyboard would be Windows + button.
@@TossSong Thanks for your reply. You mean Window key can be used as CMD on Mac?
Yes, I pretty sure, because it’s been known or documented that when using a Windows PC keyboard, the Windows key replaces CMD Mac key. When I can I’ll test it on the X8 and let you know.
@@TossSong Thank you so much. That’s the only point I’m concerning buying this.
So, I finally tested the X8. Yes, the [command] (Mac) key is [Win] key on the X8. And the [option] (Mac) key is the [Alt] key on the X8. I tested the “select all” on pictures in a folder pressing [Win] + [A] then [Win] + [Alt] + [Y] for slideshow. Everything that I would use on my MacBook work on this X8.
Why did you buy two cf cards?
Thanks for commenting. I shoot raw uncompressed on one card and jpeg on the other. The raw uncompressed can fill up fast. I now have 1TB cf and 512GB cf cards, in addition.
@@TossSong ok I only have one I just got the one you have and a regular sd card. So I can use an sd and a cf in the camera at once correct. ? Thanks for responding and thanks for the video
No problem. Yes you can use them together. And you could assign how you want them, like which one to take photos and which to take pictures or combine of both. You could examine the manual or watch it on KZread on how this can be done. On default, I believe it does everything on the card in Slot 1 first. Then when full, it switches to Slot 2…I think.
What is the best keyboard in terms of ease of pressing the keyboard buttons? Ri i4.Ri x8..k06..or What
Hi, thank you for commenting. It’s difficult to say. The K06 clickiness is best (when not typing for long), But then the keys are cramped together, and typing for Long periods could be tiring. Both the i4 and X8 keys are the same (not clicky) and are spread out more, but typing on them could be tiring no matter because they require more pressure (because of the membrane design) especially for long periods. But typing on the X8 or i4 like for log-in and google searching would just fine. They all have their negatives and positives. If I had to choose, because I don’t type long strings of words anyway when using these small keyboards-I would choose either the X8 or the i4. Note though, some i4 units have been reported that it could auto scroll sometimes without touching it.
Godox G3 MacOS V1.1. Both don't exist for download
Hi, they now have the Godox G3 Launcher V1.1 for macOS back. Side note, don’t forget to select “Update” on the trigger (Device Info) in the last step when updating it.
Hi again, they now have the Godox G3 Launcher V1.1 for macOS back. Side note, don’t forget to select “Update” on the trigger (Device Info) in the last step when updating it.
don't exist G· Launcher V1.1 MAC!!!!
Hi, thanks for reaching out. I contacted Godox, they found a problem with the macOS Launcher and took it down. They’re working on it and should be back up soon. Here’s their reply: “Thanks for your email and sorry to hear the issue had to you. We're sorry that G3 Launcher V1.1 for Mac OS was currently taken down as our technicians detected a problem and are rectifying it. We apologize for any inconvenience caused.”l
Thanks. I'll have to wait
Surprised you didn't edit this. Most important part is selecting 'update' in Device Info. page.
Hi, thanks for your input. I know that there’s a lot going on in this video, so I understand that there’s much to look at. At about 5:26 in this video, I finally did.
Thanks for the information here. I saw where the windows download said supports both platforms and nearly tried the update my X3 on my Mac with the windows version of the update. I'll just hold up until I see the Mac version posted again.
Hi again, they now have the Godox G3 Launcher V1.1 for macOS back. Side note, don’t forget to select “Update” on the trigger (Device Info) in the last step when updating it.
Thank you for the video. On 2.02 When viewing images in playback mode there is a icon overlay that is virtually telling you if you press the playback button again while you're in that mode you can go back to shooting. Um... It's a professional camera, why does one need an distracting icon to tell them that they can go back to shooting by pressing a playback button when one can just press the shutter button. Is there any way to get rid of that distracting icon? Sometimes it covers up one of my subjects eyes. And it really kills the vibe when showing clients photos you have taken.
Hi, thanks for your comment. I’ll take a look at it and see what can be done. I’ll let you know it here.
they have deleted the IOS version :/
Hi, they now have the Godox G3 Launcher V1.1 for macOS back. Side note, don’t forget to select “Update” on the trigger (Device Info) in the last step when updating it.
Great instruction video, thank you. Do you think this tablet would have any problem running the Starlink app? I tried a really cheap android 13 device and it cannot handle the app very well. Thanks!
Hi, thank you for your comment. I wouldn’t know for sure about the Starlink app (I’ve never used it). However, I think this tablet should be able to handle it. I’ve tried some graphical intense games and it has been able to handle them just fine.
@@TossSong Thank you sir, I will give it a try then!
There is no Mac os down loader on the website, can you please tell me how can I get that link. I only see 3 downloads and none of them iare mac, like it is on your video.
Hi, thanks for reaching out. I contacted Godox, they found a problem with the macOS Launcher and took it down. They’re working on it and should be back up soon. Here’s their reply: “Thanks for your email and sorry to hear the issue had to you. We're sorry that G3 Launcher V1.1 for Mac OS was currently taken down as our technicians detected a problem and are rectifying it. We apologize for any inconvenience caused.”
Hi, my godox x3 doesn’t turn on after this update, anything I can do?
Hi, thanks for reaching out. Be patient and press and hold the knob and the test button at the same time (or just the knob) until you see the arrow icon (might be a while). Repeat if you get tired. Also plug it in while the Launcher (make sure it’s G3 v1.1) is on. Then redo the update process. Let me know how it goes.
ÝsyysUzuz5
En caso de que no esté claro... GODOX X3 TIGGER 1 Abra el godox programa G3 y cargue el version firmware 2 conecte el cable según el producto al godox x3. Tenga en cuenta que está apagado 3 mantenga presionado el botón de control giratorio durante unos segundos hasta que aparezca la palabra actualización en idioma chino en el Godox X3. presiona Ir para actualizar en tu computadora, espera 15 segundos 4 Cuando la barra de progreso en verde se detenga y la ventana muy difícil de leer que está sobre ella indique que la actualización se completó, haz clic en "Salir" Finalmente y listo. Desenchufe el cable ok
En caso de que no esté claro... GODOX X3 TIGGER 1 Abra el godox programa G3 y cargue el version firmware 2 conecte el cable según el producto al godox x3. Tenga en cuenta que está apagado 3 mantenga presionado el botón de control giratorio durante unos segundos hasta que aparezca la palabra actualización en idioma chino en el Godox X3. presiona Ir para actualizar en tu computadora, espera 15 segundos 4 Cuando la barra de progreso en verde se detenga y la ventana muy difícil de leer que está sobre ella indique que la actualización se completó, haz clic en "Salir" Finalmente y listo. Desenchufe el cable ok
Thank you for commenting and sharing.
I have got exactly the same issue and it's annoying. solution is to switch to 2.4Ghz, but then if you are using dji mic 2 you won't be able to use it with mimo app connected in paralel.
Thank you for sharing and your comment. Using 2.4Ghz should do. But like you said not with the mic 2. Thing are so complicated with this.
Hi I’ve connected the i4 to iPhone 12, the keyboard working but cursor not, any idea?
Hi, thanks for reaching out. I’m not sure, have you tried rebooting the phone? Also, charged the i4 keyboard again then turn it off then on again? Let me know.
good day, it seems that I'm having trouble finding the godox g3 launcher v 1.1 for mac OS.
Hi, thanks for reaching out. Were you able to find it? I know that Godox named their softwares/app very confusing. The names are similar and the version numbers are all over the place. But hopefully you scroll through the pages carefully. Let me know.
@@TossSong right now, I am unable to find the Mac version for V1.1.
maybe you can give us a copy of the g3 launcher v1.1 for mac.
Hi again. I contacted Godox and they found a problem with the macOS version, so working on it. Here’s their reply: “Thanks for your email and sorry to hear the issue had to you. We're sorry that G3 Launcher V1.1 for Mac OS was currently taken down as our technicians detected a problem and are rectifying it. We apologize for any inconvenience caused.”
@@TossSong So will they put the Mac os download back because I don't see the mac down-loader either only the windows
cant find the app in Appstore.
Hi, did you find it? It’s “imaging edge mobile”. The app is red with “IEM” on it.
@@TossSong Found it. Its working, thanks a lottttt...
No problem. 👍
This helped me so much
Thank you for your comment. Happy this helped.
THANK YOU SO MUCH
Thank you for your comment. Glad this helped.
Totoo ba Yan
Yes. Thanks for commenting.
A useful and good video .. Godox should seriously make things more user friendly and less confusing :). A quick question though.. after the firmware update.. the group A now shows a red line below the A, is that a new feature of the new firmware? What is the significance of the red colour?
Hi, thank you for your comment. Yes, it’s a new feature from the update. I’ll double check, the red line might signify that group A is currently selected, active, or has some special status. I’ll test it and see and let you know.
@@TossSong Thank you. Earlier today i checked and they have now given an option to add colour to every group or keep it white. With colour.. Group A is Red, Group B is Green, Group C is Blue and so on.. looks nice :).
That’s nice, we could now discern the groups more easily! Thanks for sharing this.
@@TossSong That is right. Looks cool. This was an update on firmware version 1.24 on my X3C trigger. I am really liking the form factor, the interface and pretty much everything about it :).
Yes, I agree. They have been releasing more firmwares for it than their other triggers. I’m very happy about this. Again thanks for sharing.
Using VPN? Try switching that off.
Thank you for your comment and suggestion. No VPN for me. I believe it’s connection interference more so, and unfortunately for some as well.
Wow. I would not have tried without your video. Thank you.
Thank you for your comment. Glad this helped.
Great video!! Thank you for the clear instructions!
Thank you for your comment. I’m happy this was helpful.
In case it's not clear...you need to press the top knob in and hold it for a while to boot the trigger into the Chinese update screen...then use the Godox G3 app to load and update the firmware. When the green progress bar stops and the very hard to read window above it says the update is complete, click 'exit' on the app. Your trigger should now turn on. As he says, any settings you had will be wiped, but that's easy to do again.
Hey, I tried all the above but I still cant get the trigger to boot. I went through the entire green progress bar and had update device success confirmation, pressed power disconnected the cable but cannot get the trigger to boot. The trigger displays Chinese text and an arrow when I reconnect now. tried about 8 times now
Hi, thanks for reaching out. Have you got it working since?Make sure the Launcher is V1.1 and the proper firmware for your X3 for your camera. And do it again. Let me know.
@@TossSong Yes, did some Reddit surfing and found that the G3 updater I was using was V1.00 and it worked correctly on Ver1.01. I thought I Bricked it but happy its working. Also seems to have fixed my TTL issues I was having with odd exposures so another plus. Updated from Version 1.09 to 1.14. Thanks for the reply anyway.
So how did you solve this? Mine won't turn on no matter how many times I plug it in or out!
Thanks for reaching out. Try keep pressing and hold the knob for a while. Until you see text in Chinese. Release then try again. Be patient. Also, have to updater app on and try again and plug it in. Let me know how it goes. Thanks.
@@TossSong I got it working after I commented…but then I couldn’t get the trigger to fire on my Canon R5. I reinstalled the firmware but it still didn’t work. I tried my XPro trigger and it worked fine so I knew it was the x3. I cleaned the hotshoe and contacts and checked my camera settings and still nothing. I reseated the trigger a couple times which didn’t work. Finally I put the trigger on all the way into the hot shoe then pulled it back just a bit. Now it’s working! I don’t remember the trigger being that fussy before upgrading to firmware 1.24….Thanks for your help!
Glad it works now. Don’t know why it’s fuzzy like that. Each X3’s contacts for each type of camera is different. Hopefully it’s not a quality control issue. When you can let me (us) know how it goes in the long run. Others may also be curious. Thanks.
You need to have the v1.1 version of the G3 app, and I could only find a link to a Windows version, you need to have that program running, and you need to have selected the firmware file. Finally, you need to have the USB cable connected between the computer and the X3. When I did all that, and pressed and held the knob for a few seconds, the X3 turns on displaying a chinese upgrade screen. Hope this helps.
@@TossSong It's important that the USB cable is connected and the G3 1.1 app is running and have a firmware file selected for this to work. Skipping any of those steps and my X3 would not turn on and seemed to be dead.
Nice video brother, Tell me wht is bettery backup shooting canon v10? Mostly in youtuber said its bettery not good . Tell me wht is ur experience about its bettery life.
Hi, thank you for your comment. The battery isn't bad in my opinion... when using it and charging it frequently. But compared to the Osmo Pocket 3, it's not good. When not used for a while, the V10 battery drains really fast. Unlike the V10, the Pocket 3's battery is great, and when not used for a while, it still retains charge and doesn't drain completely. For example, in a month or two without use, the Pocket 3 would drain to about 80%. The V10 would be completely empty in a week or two. I can say with certainty that Canon uses a cheap battery in their V10, and I don't like that.
@@TossSong thx brother ur rply really help me to take my decision.
No problem. Happy to help.
Great spec video .. but Should try on a person or bigger object for real life situation
Thank you for your comment and input. Just more like a first impression video. But you’re right, I could have done more.
After updating the controller, did it change what steam recognize it as? I am wondering if I can make steam recognize it as a xbox elite controller so I can map the back buttons directly from steam.
I will check again and let you know.
@@TossSongThank you! Also can you tell me which adapter you use for the type c charging cable? Looks pretty convenient!
Yes, I got the magnetic adapter from Amazon. If your search “USB-C magnetic adapter”, you’ll find several brands. Anyway, I just checked Steam, it no longer shows the name of the controller other than “Xinput controller”. However in “Begin Test”, it still shows the old outline image of the Xbox 360 controller and “Device Support: 45e-28e-4bfcbe17”. In Windows 11, it’s “Flydigi VADER 3”.
can u take stills/photos with the osmo
Hi, thanks for reaching out. Yes, the DJI Osmo Pocket 3 can take still photos. It has a 9.4 MP resolution, 20 mm f/2.0 lens, and 1-inch CMOS sensor. It’s doesn’t have high megapixels, but the 1-in sensor does great.
Gulikit is lying about the accuracy of their sticks, on the cyclic test they show 0 per cent of errors because they joystick adjusts the value at the level of software and not hardware. The same cyclic result can be achieved in apex 4 if you adjust the stick response curve, but there the result will be more honest.
Thanks for comment and also for the info. This is very good detail on circular test. I’d like to into it, interesting!
does the fx3 has this setup
Hi, thanks for reaching out. According to Sony support page, Yes. But you would have to have camera firmware Ver. 3.00 or later (if not, just update it). Moreover, you would also have to have Sony compatible lens for this feature to work. helpguide.sony.net/ilc/2210/v1/en/contents/TP1000882810.html support.d-imaging.sony.co.jp/www/cscs/function/compatibility.php?fnc=1001&area=gb&lang=en&ref=1
@@TossSong great thank you