was wondering what tradio and battery pack are you using?
@B2Humla4 күн бұрын
It is two batteries, "Sunpadow Platin Stock Racing 8000mAh 7.4V 2S 130/65C LiPo". They are connectied in series so we have 4S volt. I am not doing any serious racing (yet), so if you are into racing (I believe they do 7 minutes races) ask the people that are doing that. I have seen some people using 9000mah batteries. Radio? I am using a Spektrum DX5, but any radio and receiver for rc racing will do ok.
@ladrao77720 күн бұрын
Very nice practice run!!! ;-)
@narongrachmareongsit1978Ай бұрын
❤😂🎉😢😮😅😊. ไฟแอดพ์. ?
@TinyTiresRCАй бұрын
I have run one of these for a few years now. Still an impressive car. In my groupe of friends we all have front wheel drive cars, and the Schumacher is tops. Equipped with a 17.5 motor it out guns similar cars equipped with 13.5 motors. We dont run timing or ESC tuning either. I did purchase the optional shocks for it as the kit shocks I found to be kind of ridiculous.
@B2HumlaАй бұрын
Yes stock shocks was almost funny to build. I believe Schumacher RC has dropped the Mission FT now. Bad, because the low kit price was attractive and got a lot of people into the hobby as their first rc racing car.
@TinyTiresRCАй бұрын
@@B2Humla Definitely a little bothered by the loss of the FT as a Kit. Fortunately parts are still available, not that it breaks all that often. It's a sturdy platform when used appropriately. Plus I purchased a myriad of spares when I bought the kit. I'm pleasantly surprised how durable it has proven to be.
@LyroLife2 ай бұрын
I am excited for future videos
@LyroLife3 ай бұрын
I love the xray XT2. Great driving.
@B2Humla3 ай бұрын
It's a sweet little car 😊
@Poonslaya3 ай бұрын
How is your vs2 holding up? I replaced my engine with the lrp .32 spec 4. And also after burning through a set of aluminium shoes I’m upgrading the clutch to the reds tetra clutch and going up to 19 teeth on the clutch bell.
@B2Humla3 ай бұрын
I used only the stock engine and pinion. It ran good with the right glow plug. I later converted it to electric, but I sold it later. Today I got a Serpent SRX8 1/8 nitro buggy. Will post some more nitro videos later when I got time. Also a Mugen 1/8 track nitro and a Serpent 1/8 GT nitro I will test this summer I hope.
@Poonslaya3 ай бұрын
@@B2Humla sweet I’m intrested in the serpent aswell will be good to see some up close vids of it fella. Happy bashing
@OliveiraX3 ай бұрын
Nice location. You should delete the chicane right in front of you. It's dangerous for the cars. If you are less than smooth with the steering, you'll upset the car, loose the rear, and crash hard against the kerb. Plus, you need a proper home straight. Especially for the 1/8 - it does not like sudden changes of direction and it likes free flowing circuits. With that much space you can go full throttle with it and practice full throttle turns too, without any fear of crashing it.
@B2Humla3 ай бұрын
Thanks. Will test new layout next time. This location is in use so we cant make a permanent rc track there.
@OliveiraX3 ай бұрын
@@B2Humla Of course. I understood. I meant making a circuit using chalk and cones, like you did. I was just advising how to improve the circuit for the 1/8 car. It needs speed (and the aerodynamic downforce that comes from it) to work well. At low speeds, it is very hard to control. It has very little grip. Once it gets up to speed it turns and brakes much better.
@nolan26944 ай бұрын
😢 'Promo SM'
@B2Humla3 ай бұрын
Not sure what you mean, but thanks anyway.
@99milesaway414 ай бұрын
You deserve more subscribers, brother, I really enjoy your videos. Especially your full throttle nitro videos on the dirt and gravel lots, they're a lot of fun to watch
@B2Humla3 ай бұрын
Thanks. I just hope the videos can be of some help to others.
@alantaylor3534 ай бұрын
YES.!!!
@LyroLife5 ай бұрын
The new traxxas rally vxl looks like a nice chassis to drive.
@B2Humla4 ай бұрын
I love rally cars. Had a HPI WR8 some time ago. For rally and some off-road I maybe prefer a short-course type of car. They also got some bigger wheels. Like the Team Associated Pro4 SC10 or a Traxxas Slash 4WD.
@talosaz15 ай бұрын
A true murder
@Fatandslowbuthasthemostfun5 ай бұрын
Where is this track located?
@B2Humla5 ай бұрын
Close to city Bergen, in Norway.
@taylorlakin14116 ай бұрын
Promo`SM 🌟
@bharris01288 ай бұрын
What is the part number for the asphalt tires? I see several options from Schumacher, but they don't explain which is for asphalt. Thank you for posting.
@B2Humla7 ай бұрын
Some stiffer (higher shore grade) rubber tires is used outdoor on asphalt. So I guess the part number can be the same, just the shore grade is different. Indoor on carpet shore 28 is common, with tire additive. Outdoor stiffer rubber so about shore 32-34. Depends on temperature and some heat up the rubber before the race. Additive may be used if the race rules permit it. This video has some tire part numbers, see description kzread.info/dash/bejne/aaWH0cOIYsjgks4.html
@miketemperante63839 ай бұрын
WHAT TIRES ARE YOU USING?
@B2Humla9 ай бұрын
GRP GTH03-XM3 or some GRP rain tires if more grip is needed.
@marcowerner873910 ай бұрын
That car is screaming help. Did you piss in the tank?
@B2Humla10 ай бұрын
It's running ok, and tuned for high speed (lean). I like the sound, nitro engines scream 👍
@nsbob7010 ай бұрын
Here's a tip, if you didn't know it already,, Make sure your throttle travel is set to 150% in the radio's settings.
@B2Humla10 ай бұрын
Thanks
@lightningrc110 ай бұрын
Great car!
@B2Humla10 ай бұрын
Yes and no belts so can drive it on street roads also
@lightningrc110 ай бұрын
Yup@@B2Humla
@boostfed7437 ай бұрын
Any issues with fitting that Body?
@jbd10010 ай бұрын
😊 good car !
@B2Humla10 ай бұрын
Thanks 😁
@jbd10010 ай бұрын
J'ai le même bolide 989E. 👍👍👍
@B2Humla10 ай бұрын
Excellent car. Just buy some spare belts end pulleys. Small rocks can break both belts and pulleys.
@lukeluke171510 ай бұрын
nice video, why don't choose 990e
@B2Humla10 ай бұрын
I bought the 989E for 50% of new price just before the 990e came out.
@Top-Jimmy10 ай бұрын
A good way to get your wheel arches perfect is to wrap some 80 grit sandpaper around a spray paint can and rotate it back and forth. I like the yellow one most. It didn't mess with my OCD as much 😂 BTW - Those Louise Tyres and wheels absolutely rip!!...Very cool.. Good for you bro.. great fun indeed customising. All the best from Australia 🙂
@B2Humla10 ай бұрын
Thanks!
@runit577211 ай бұрын
& THAT folks there's the reason why ya don't run a badass luxury on-road car in a random lot.. It loves fresh paved blacktop!!
@B2Humla11 ай бұрын
Yes but I had to test it anyway 🚀
@josteinhelland578411 ай бұрын
God stemning Bjørn!
@danielmaganja279511 ай бұрын
hej snygg bil jag köpte 2 st mugen mrx4x med delar och startare + hudy setup för 1800 :-sek
@B2Humla11 ай бұрын
That is a steal! Hard to find spare parts to this car so drive it carefully :)
@danielmaganja279511 ай бұрын
@@B2Humla i havet spare parts going in The buying process
@marcthaywood9647 Жыл бұрын
Yea, we lock the fronts over here...
@46ARF Жыл бұрын
Thank you for taking the time to upload very detailed videos. Unfortunately, there isn't too many technical information on these class of vehicles. Also, if you could please continue posting videos of your serpent vipers! I love that car and am looking to buy the new 990E
@jbrotv4905 Жыл бұрын
설명이 너무 잘되어 있어서 감사합니다. Thanks ^^
@tHe_ViL1aiN Жыл бұрын
🤔 what's your end voltage after the 7min?
@B2Humla Жыл бұрын
About 3.85v each cell, so storage voltage. With 8000mah batteries.
@tHe_ViL1aiN Жыл бұрын
@@B2Humla ok kool thanks
@Acitrain Жыл бұрын
Have a good day Is there any deterioration in guitars tone or intonation?
@B2Humla Жыл бұрын
The tone is good, the frets not perfect but ok. Intonation is ok. I believe a used Ibanez Jem Prestige or Premium is maybe better buy, but I wanted the Jem777 look for a low price.
@Acitrain Жыл бұрын
@@B2Humla ok then thank u
@hallofgame5721 Жыл бұрын
Selling brother?
@B2Humla Жыл бұрын
Sold long time ago as I am now more doing racing, onroad or buggy.
@NielsHeusinkveld Жыл бұрын
Hey, I'm playing around with a pc simulator trying to make such a car. Would you be willing to make some measurements on your 989E for me? Early video here: kzread.info/dash/bejne/fnWb0MSggNOtosY.html
@schwangmeister Жыл бұрын
Hi, I was wondering how well the guitar neck is holding up.
@B2Humla Жыл бұрын
Hi. All good. For the price I still think the neck is good. But quality control from China is not always great. 👍
@meudrone4k369 Жыл бұрын
Top carro 🚗 😊
@ladrao777 Жыл бұрын
I like your commentary and the work tha you do. Keep up the great content.
@B2Humla Жыл бұрын
Thanks. Nice if it can help some. I just show my experience with the RC hobby.
@josetapia4018 Жыл бұрын
Good info brother 👏
@die1225 Жыл бұрын
Did u just try and tune it right after you started it? That's not how you do it, ever, never get a good tune by trying to tune on a cold engine
@B2Humla Жыл бұрын
No I first used engine warner. Then start and let it idle to about 80 degrees Celsius. Then run slow for a few minutes until about 100 degrees Celsius where the engine can be tuned.
@rcaddictgarage Жыл бұрын
Great place to run! Thanks for the footage.
@Ctxify Жыл бұрын
Ladybug ;)
@LOLRC Жыл бұрын
:)
@BlackThunderRC Жыл бұрын
Would be a good idea to take the posts off of the motor. And in a crash or just from use they put a torque onto the PCB mount. And eventually cause it to fail. Best to solder right onto the PCB pads of the motor. But love the video and very nicely built !
@B2Humla Жыл бұрын
Agree. I've also seen the contacts almost come off while driving. So agree that the safest thing is to solder straight on.
@BlackThunderRC Жыл бұрын
@@B2Humla I learned the hard way 😂
@LoveLove-ld6ey Жыл бұрын
Did a bad review on this item did not prompt me to buy. No rough driving no ripping out the hole driving like a woman
@B2Humla Жыл бұрын
I had trouble to get the engine to run good, because I used wrong glow plug. But later with correct glow plug it did drive good. I have a few videos later where I drive it more. But it is converted to electric now. Sometimes I drive like a baby, that is also legal 😀
@krispip5079 Жыл бұрын
how do I get one for notorious 6s V5 ?
@B2Humla Жыл бұрын
Try this webpage 3d-rc.online/products/new-arrma-6s-high-profile
@krispip5079 Жыл бұрын
@@B2Humla Found them and have ordered a few things ! Thanks for your reply 👍
@rcaddictgarage Жыл бұрын
Sweet👍
@Chris-adams-rc-journey Жыл бұрын
Next car I buy is definitely going to be vte. I need a 1\8 gt car. Thanks for reviewing.
@B2Humla Жыл бұрын
Yes is looks to be a good car for a good price. I just uploaded a new video, electronics is now in the car. Have to wait for some warmer and better weather before I can do some speed test and driving.
@dnyspeed Жыл бұрын
did you have the og air filter on this video or did you get the unrestricted air filter
@B2Humla Жыл бұрын
I use air filter all the time. I used what HPI call the new and some better airfilter, but I did not notice that big difference. The car runs excellent with this 4.6/.28 HPI engine.
@robpshannonjr Жыл бұрын
Thank you, sir! This was EVERYTHING I needed to know.
Пікірлер
was wondering what tradio and battery pack are you using?
It is two batteries, "Sunpadow Platin Stock Racing 8000mAh 7.4V 2S 130/65C LiPo". They are connectied in series so we have 4S volt. I am not doing any serious racing (yet), so if you are into racing (I believe they do 7 minutes races) ask the people that are doing that. I have seen some people using 9000mah batteries. Radio? I am using a Spektrum DX5, but any radio and receiver for rc racing will do ok.
Very nice practice run!!! ;-)
❤😂🎉😢😮😅😊. ไฟแอดพ์. ?
I have run one of these for a few years now. Still an impressive car. In my groupe of friends we all have front wheel drive cars, and the Schumacher is tops. Equipped with a 17.5 motor it out guns similar cars equipped with 13.5 motors. We dont run timing or ESC tuning either. I did purchase the optional shocks for it as the kit shocks I found to be kind of ridiculous.
Yes stock shocks was almost funny to build. I believe Schumacher RC has dropped the Mission FT now. Bad, because the low kit price was attractive and got a lot of people into the hobby as their first rc racing car.
@@B2Humla Definitely a little bothered by the loss of the FT as a Kit. Fortunately parts are still available, not that it breaks all that often. It's a sturdy platform when used appropriately. Plus I purchased a myriad of spares when I bought the kit. I'm pleasantly surprised how durable it has proven to be.
I am excited for future videos
I love the xray XT2. Great driving.
It's a sweet little car 😊
How is your vs2 holding up? I replaced my engine with the lrp .32 spec 4. And also after burning through a set of aluminium shoes I’m upgrading the clutch to the reds tetra clutch and going up to 19 teeth on the clutch bell.
I used only the stock engine and pinion. It ran good with the right glow plug. I later converted it to electric, but I sold it later. Today I got a Serpent SRX8 1/8 nitro buggy. Will post some more nitro videos later when I got time. Also a Mugen 1/8 track nitro and a Serpent 1/8 GT nitro I will test this summer I hope.
@@B2Humla sweet I’m intrested in the serpent aswell will be good to see some up close vids of it fella. Happy bashing
Nice location. You should delete the chicane right in front of you. It's dangerous for the cars. If you are less than smooth with the steering, you'll upset the car, loose the rear, and crash hard against the kerb. Plus, you need a proper home straight. Especially for the 1/8 - it does not like sudden changes of direction and it likes free flowing circuits. With that much space you can go full throttle with it and practice full throttle turns too, without any fear of crashing it.
Thanks. Will test new layout next time. This location is in use so we cant make a permanent rc track there.
@@B2Humla Of course. I understood. I meant making a circuit using chalk and cones, like you did. I was just advising how to improve the circuit for the 1/8 car. It needs speed (and the aerodynamic downforce that comes from it) to work well. At low speeds, it is very hard to control. It has very little grip. Once it gets up to speed it turns and brakes much better.
😢 'Promo SM'
Not sure what you mean, but thanks anyway.
You deserve more subscribers, brother, I really enjoy your videos. Especially your full throttle nitro videos on the dirt and gravel lots, they're a lot of fun to watch
Thanks. I just hope the videos can be of some help to others.
YES.!!!
The new traxxas rally vxl looks like a nice chassis to drive.
I love rally cars. Had a HPI WR8 some time ago. For rally and some off-road I maybe prefer a short-course type of car. They also got some bigger wheels. Like the Team Associated Pro4 SC10 or a Traxxas Slash 4WD.
A true murder
Where is this track located?
Close to city Bergen, in Norway.
Promo`SM 🌟
What is the part number for the asphalt tires? I see several options from Schumacher, but they don't explain which is for asphalt. Thank you for posting.
Some stiffer (higher shore grade) rubber tires is used outdoor on asphalt. So I guess the part number can be the same, just the shore grade is different. Indoor on carpet shore 28 is common, with tire additive. Outdoor stiffer rubber so about shore 32-34. Depends on temperature and some heat up the rubber before the race. Additive may be used if the race rules permit it. This video has some tire part numbers, see description kzread.info/dash/bejne/aaWH0cOIYsjgks4.html
WHAT TIRES ARE YOU USING?
GRP GTH03-XM3 or some GRP rain tires if more grip is needed.
That car is screaming help. Did you piss in the tank?
It's running ok, and tuned for high speed (lean). I like the sound, nitro engines scream 👍
Here's a tip, if you didn't know it already,, Make sure your throttle travel is set to 150% in the radio's settings.
Thanks
Great car!
Yes and no belts so can drive it on street roads also
Yup@@B2Humla
Any issues with fitting that Body?
😊 good car !
Thanks 😁
J'ai le même bolide 989E. 👍👍👍
Excellent car. Just buy some spare belts end pulleys. Small rocks can break both belts and pulleys.
nice video, why don't choose 990e
I bought the 989E for 50% of new price just before the 990e came out.
A good way to get your wheel arches perfect is to wrap some 80 grit sandpaper around a spray paint can and rotate it back and forth. I like the yellow one most. It didn't mess with my OCD as much 😂 BTW - Those Louise Tyres and wheels absolutely rip!!...Very cool.. Good for you bro.. great fun indeed customising. All the best from Australia 🙂
Thanks!
& THAT folks there's the reason why ya don't run a badass luxury on-road car in a random lot.. It loves fresh paved blacktop!!
Yes but I had to test it anyway 🚀
God stemning Bjørn!
hej snygg bil jag köpte 2 st mugen mrx4x med delar och startare + hudy setup för 1800 :-sek
That is a steal! Hard to find spare parts to this car so drive it carefully :)
@@B2Humla i havet spare parts going in The buying process
Yea, we lock the fronts over here...
Thank you for taking the time to upload very detailed videos. Unfortunately, there isn't too many technical information on these class of vehicles. Also, if you could please continue posting videos of your serpent vipers! I love that car and am looking to buy the new 990E
설명이 너무 잘되어 있어서 감사합니다. Thanks ^^
🤔 what's your end voltage after the 7min?
About 3.85v each cell, so storage voltage. With 8000mah batteries.
@@B2Humla ok kool thanks
Have a good day Is there any deterioration in guitars tone or intonation?
The tone is good, the frets not perfect but ok. Intonation is ok. I believe a used Ibanez Jem Prestige or Premium is maybe better buy, but I wanted the Jem777 look for a low price.
@@B2Humla ok then thank u
Selling brother?
Sold long time ago as I am now more doing racing, onroad or buggy.
Hey, I'm playing around with a pc simulator trying to make such a car. Would you be willing to make some measurements on your 989E for me? Early video here: kzread.info/dash/bejne/fnWb0MSggNOtosY.html
Hi, I was wondering how well the guitar neck is holding up.
Hi. All good. For the price I still think the neck is good. But quality control from China is not always great. 👍
Top carro 🚗 😊
I like your commentary and the work tha you do. Keep up the great content.
Thanks. Nice if it can help some. I just show my experience with the RC hobby.
Good info brother 👏
Did u just try and tune it right after you started it? That's not how you do it, ever, never get a good tune by trying to tune on a cold engine
No I first used engine warner. Then start and let it idle to about 80 degrees Celsius. Then run slow for a few minutes until about 100 degrees Celsius where the engine can be tuned.
Great place to run! Thanks for the footage.
Ladybug ;)
:)
Would be a good idea to take the posts off of the motor. And in a crash or just from use they put a torque onto the PCB mount. And eventually cause it to fail. Best to solder right onto the PCB pads of the motor. But love the video and very nicely built !
Agree. I've also seen the contacts almost come off while driving. So agree that the safest thing is to solder straight on.
@@B2Humla I learned the hard way 😂
Did a bad review on this item did not prompt me to buy. No rough driving no ripping out the hole driving like a woman
I had trouble to get the engine to run good, because I used wrong glow plug. But later with correct glow plug it did drive good. I have a few videos later where I drive it more. But it is converted to electric now. Sometimes I drive like a baby, that is also legal 😀
how do I get one for notorious 6s V5 ?
Try this webpage 3d-rc.online/products/new-arrma-6s-high-profile
@@B2Humla Found them and have ordered a few things ! Thanks for your reply 👍
Sweet👍
Next car I buy is definitely going to be vte. I need a 1\8 gt car. Thanks for reviewing.
Yes is looks to be a good car for a good price. I just uploaded a new video, electronics is now in the car. Have to wait for some warmer and better weather before I can do some speed test and driving.
did you have the og air filter on this video or did you get the unrestricted air filter
I use air filter all the time. I used what HPI call the new and some better airfilter, but I did not notice that big difference. The car runs excellent with this 4.6/.28 HPI engine.
Thank you, sir! This was EVERYTHING I needed to know.
Wonderful 👑!! Best subs provider -> Promo-SM!!!