It got worse and I wonder why... :S if I had some black bricks on the test page, before this procedure, after the cleaning with a Printhead cleaning solution I got no black brick at all. Moreover some of the red and yellow bricks are now missing as well... I have performed the Cleaning function several times and again nothing happens... I injected 4 ml of solution two times, the first time it was at room temperature and the second it was warmed in hot water. The black color has just dissapeared. :S
@micaiahiam2 ай бұрын
Am I the only one to whom this method has failed? Followed through revert instruction but now my printer is printing worst than before. First no ink at all came out and now only magenta and yellow do. I’ve done like 8 cleaning cycles..
@anightin2 ай бұрын
It sounds like the cartridges are a bit low (they need to be at least half-full to prime the head. Or, more likely, that there's air in the head. There are instructions in the troubleshooting about this but you're really just trying to inject a small amount of fluid to displace any air that's in the head.
@micaiahiam2 ай бұрын
@@anightin replaced ink cartridges and forced a bit of fluid into the head taking care no air was in the tube, ran several cleaning cycles but still no blue. I must have messed something up in the process.
@beyondfamilyscapegoatingabuse2 ай бұрын
This worked - Thank you!!!
@richardc81293 ай бұрын
I'm getting an error code of OXB81A81CE, (LINE BREAK) P1 OXEO1A81CE. It's on an HP Officejet Pro X451dn. I cannot find the codes online anywhere. anyone have a reference link? Thanks in advance.
@laurenceplumley4333 ай бұрын
Super presentation thanks…
@nigratruo3 ай бұрын
How can you tell which printers this works for? Adapters? I have a HP Photosmart D7300, the 6 individual cartridges are not directly riding on the print head, but are installed horizontally and stationary.
@user-xh8xi2ej7u4 ай бұрын
Nice video , thanks
@petergare47664 ай бұрын
So far so good. I was really struggling getting the rubber tubing on to the print nozzle. I found putting the tubing in an empty biro body was great to use as a guide, then connected the other end to the syringe after getting the air out.
@typosim4 ай бұрын
Certain MODEL cannot use this method expecially the high end model ... it will damage the print head and make it even worst the glascate inside will be miss alighned
@Lorraines_Mini_Kingdom5 ай бұрын
Any advice if you can't push any fluid through due to resistance , if you pull slightly it snaps back due to a vacuum. Will it just take weeks to slowly do it? It's been unused for sometime and yellow that's blocked.
@novokomp5 ай бұрын
The towel is easy to tuck in with a ruler
@garylee35517 ай бұрын
Where did you get that green adapter?
@dominiquegagnon64687 ай бұрын
merci!
@csjames699 ай бұрын
My HP printer died so went and dug out my old Brother MFC 235C printer. Placed new cartridges and nothing prints. Just watched your video so I’ll try and rescue the printer.
@08mraskew9 ай бұрын
why are you whispering again?
@slgale65509 ай бұрын
How to get rid of the message “unable to print 51”
@002seleena11 ай бұрын
This is a really good printer kzread.infoUgkxciSwynMJ7PnUvvx11rewiu-yFBkZTl53 . The reason I gave 4 stars for tech support (which I don't think this would classify as tech support) is because once you turn the printer on, it does require a little bit of start up time which may bother some who are in a hurry to quickly print something. To offset that though the printer prints very quickly. I would definitely purchase this printer again.
@hydrotricine11 ай бұрын
Thank you! Solved my problems,printing great now
@chiefonthetube Жыл бұрын
I have an Epson WF3640. When the print check started showing missing lines I cleaned print head with a cleaning solution I bought on Amazon. I thought I was really doing something because so much ink came out of the print head. I even waited and repeated the process the next day until cleaning solution came through almost clear. To my surprise the print quality was even worse than before. Way worse. What am I missing?
@KaranSingh-ro4hz Жыл бұрын
gandu vdo
@chrisreed3022 Жыл бұрын
Yep! That did it. Fixed a printer that had been in the attic for 5 yrs. Went from poor to perfect in 10 minutes. Recommended. Saved me a fortune on a new printer.
@coachjrshel Жыл бұрын
Do you have a kit for the mfc j995dw? The nozzles on the j995dw appear to be designed like a valve stem on a tire. Would need a very special tube to press the center piece out of the way to allow for cleaner to enter.
@judyjohnson630 Жыл бұрын
can barely hear anything in this video...
@user-kx2yd5wn2m Жыл бұрын
I tried this to sort out alignment issues but to no avail and to be fair this wasn't what this video is for. But I was willing to try anything. This video deserves a thumbs up as it's great for those who are suffering from blocked print heads and I will probably order the kit just as a backup. The built-in manual & auto alignment didn't work either. What did the trick was this video: kzread.info/dash/bejne/mYWOlcexYMXdp8Y.html
@user-wp4ke2qc2e Жыл бұрын
Very clear and useful instructions! I successfully carried this out on my MFC-985dw printer. Per another post, I used regular Windex to flush with, as I didn't have access to special cleaning solution (not heated) . I also blotted the "resting" sponge on the left-hand side several times with a paper towel saturated with WIndex to remove most of the ink that had filled it up.
@PostprandialTorpor Жыл бұрын
Why does the power need to be on during an overnight cleaning?
@marek200k Жыл бұрын
fluid should be injected directly into the head
@willburr8226 Жыл бұрын
The simple comment you made of air in the heads not allowing ink to flow was what made the difference for me! Thanks!
@TheBestIsWorthTheWait Жыл бұрын
Thank you!!!! After looking at several other videos you were the only one that gave the secret (02:35--02:53) of how to unlock the printer head to allow cleaning!!!!!!!!
@garymooney1113 Жыл бұрын
The kit worked! I'm so impressed on my Brother MFC-J650DW printer. I found the video to be more useful than the printed instructions. A few comments / suggestions. It's messy, so wear the gloves for sure, and wrap up the cartridges upon removing them, because one or more will leak. I had no trouble placing a folded paper towel in the printhead track and moving the printhead over it. I found the tubing to be a bit tight to get onto the nozzle, so I made a very short cut in the end, which helped. There was some leakage into the cartridge area, which I dabbed up before reinserting the cartridges. After finishing the procedure and doing a test print, the result was pretty ugly, and part of the colours were washed out due to the cleaning fluid (too much used?). However, after running the normal cleaning process three times, everything was perfect. I've been using clone ink, and I now wonder if that's why the printhead became clogged. I really appreciate this product -- saved me from discarding a printer that is perfectly good otherwise.
@Nebula37 Жыл бұрын
I'm a teacher, and I inherited a Brother DCP-T300 from a guy who went overseas. I took it to my office at school. Test prints showed that the black and yellow print heads in particular were clogged. I ordered a cleaning kit online. The process seemed promising for the magenta and cyan heads, but I didn't seem to get any suction resistance when attempting to clean the yellow and black heads. Has anyone ever experienced that? Later that day, the yellow and black inks leaked all through the bottom of the printer, causing a huge mess. I re-cleaned everything and attempted print head cleaning again. Then I cautiously partly re-filled the yellow and black containers and attempted test printing again but got "Unable to Print" error, and the containers leaked all over the desk and printer again. I've heard that I can re-open the printer and clean a ribbon, but that won't solve the leaking and lack of suction for the yellow and black cartridges. Any suggestions?
@tvenergyproductions1 Жыл бұрын
Great video. Do you know why the cd/dvd tray is not accepted with the message 'cd tray loaded incorrectly' on an Epson XP-750?
@DenkyManner Жыл бұрын
i had 4 blocked nozzles. What fixed it was running the cleaning over and over again. first the black came back. Then after another load they all worked
@6CCORVETTEMAN Жыл бұрын
When injecting the alcohol, the syringe was very hard to press and withdraw. I worked it this way numerous times. Still bad printing. Finally, I more forcefully injected the alcohol and then heard a "POP." I thought the black ink line had detached somewhere or the print head was now unclogged I could then easily inject and withdraw the alcohol. And, i could hear air being forced out of the print head. And then, after several cleaning cycles, by the machine, my black print is outstanding! I determined that the "POP" I heard was a valve or clog that was opened up.
@Amenhotepish Жыл бұрын
$10 Shipping to Canada. Not worth the cost but a great video none the less. Cheers.
@recoswell Жыл бұрын
your cleaning kit is a bigger CHUNK OF SHIT than you are
@khloegoncalves6966 Жыл бұрын
Where can I get the adapter piece?
@nb987 Жыл бұрын
Great video. Thank you.
@newbeatlee Жыл бұрын
excelent tip to clean it , i hope it helps me with a mfc-240c printer i had . regards from mexico
@tuantran-zu2lv Жыл бұрын
i want to buy epson xp600 print head cleaning solution using eco sloven ink can you help me
@vanessateo22 Жыл бұрын
Where do I find the adapter for my xp8500?
@saddb Жыл бұрын
Excellent video thank you, I have a kit but has no adaptor for 700 (rectangular) series, where in UK can you buy these adaptors please?
@anightin Жыл бұрын
Drop me a line and I'll post one out free of charge
@davidherz9968 Жыл бұрын
by far the clearest and best filmed, thank you
@MrFehmin Жыл бұрын
*It prints like no other **Bestt.Digital** printer. i have always loved Epson for the colors they produce.*
@dierenfilmpjes5136 Жыл бұрын
*Loving my **Bestt.Digital** portable Printer. Small enough to carry in my little bag and not at all heavy. Getting a lot of use out of it and having a great time printing on the go. Works for me.*
@airecrist2 жыл бұрын
So what if a color or in my case black(not a color😉) still won't print after cleaning?.... the printhead is cleared... fluid goes through fine.... colors are fine just black won't print... seems like it may put a little black(super faint grey shade) on the print quality test but that's it....
Пікірлер
Question, where did you buy that eco tank?
It got worse and I wonder why... :S if I had some black bricks on the test page, before this procedure, after the cleaning with a Printhead cleaning solution I got no black brick at all. Moreover some of the red and yellow bricks are now missing as well... I have performed the Cleaning function several times and again nothing happens... I injected 4 ml of solution two times, the first time it was at room temperature and the second it was warmed in hot water. The black color has just dissapeared. :S
Am I the only one to whom this method has failed? Followed through revert instruction but now my printer is printing worst than before. First no ink at all came out and now only magenta and yellow do. I’ve done like 8 cleaning cycles..
It sounds like the cartridges are a bit low (they need to be at least half-full to prime the head. Or, more likely, that there's air in the head. There are instructions in the troubleshooting about this but you're really just trying to inject a small amount of fluid to displace any air that's in the head.
@@anightin replaced ink cartridges and forced a bit of fluid into the head taking care no air was in the tube, ran several cleaning cycles but still no blue. I must have messed something up in the process.
This worked - Thank you!!!
I'm getting an error code of OXB81A81CE, (LINE BREAK) P1 OXEO1A81CE. It's on an HP Officejet Pro X451dn. I cannot find the codes online anywhere. anyone have a reference link? Thanks in advance.
Super presentation thanks…
How can you tell which printers this works for? Adapters? I have a HP Photosmart D7300, the 6 individual cartridges are not directly riding on the print head, but are installed horizontally and stationary.
Nice video , thanks
So far so good. I was really struggling getting the rubber tubing on to the print nozzle. I found putting the tubing in an empty biro body was great to use as a guide, then connected the other end to the syringe after getting the air out.
Certain MODEL cannot use this method expecially the high end model ... it will damage the print head and make it even worst the glascate inside will be miss alighned
Any advice if you can't push any fluid through due to resistance , if you pull slightly it snaps back due to a vacuum. Will it just take weeks to slowly do it? It's been unused for sometime and yellow that's blocked.
The towel is easy to tuck in with a ruler
Where did you get that green adapter?
merci!
My HP printer died so went and dug out my old Brother MFC 235C printer. Placed new cartridges and nothing prints. Just watched your video so I’ll try and rescue the printer.
why are you whispering again?
How to get rid of the message “unable to print 51”
This is a really good printer kzread.infoUgkxciSwynMJ7PnUvvx11rewiu-yFBkZTl53 . The reason I gave 4 stars for tech support (which I don't think this would classify as tech support) is because once you turn the printer on, it does require a little bit of start up time which may bother some who are in a hurry to quickly print something. To offset that though the printer prints very quickly. I would definitely purchase this printer again.
Thank you! Solved my problems,printing great now
I have an Epson WF3640. When the print check started showing missing lines I cleaned print head with a cleaning solution I bought on Amazon. I thought I was really doing something because so much ink came out of the print head. I even waited and repeated the process the next day until cleaning solution came through almost clear. To my surprise the print quality was even worse than before. Way worse. What am I missing?
gandu vdo
Yep! That did it. Fixed a printer that had been in the attic for 5 yrs. Went from poor to perfect in 10 minutes. Recommended. Saved me a fortune on a new printer.
Do you have a kit for the mfc j995dw? The nozzles on the j995dw appear to be designed like a valve stem on a tire. Would need a very special tube to press the center piece out of the way to allow for cleaner to enter.
can barely hear anything in this video...
I tried this to sort out alignment issues but to no avail and to be fair this wasn't what this video is for. But I was willing to try anything. This video deserves a thumbs up as it's great for those who are suffering from blocked print heads and I will probably order the kit just as a backup. The built-in manual & auto alignment didn't work either. What did the trick was this video: kzread.info/dash/bejne/mYWOlcexYMXdp8Y.html
Very clear and useful instructions! I successfully carried this out on my MFC-985dw printer. Per another post, I used regular Windex to flush with, as I didn't have access to special cleaning solution (not heated) . I also blotted the "resting" sponge on the left-hand side several times with a paper towel saturated with WIndex to remove most of the ink that had filled it up.
Why does the power need to be on during an overnight cleaning?
fluid should be injected directly into the head
The simple comment you made of air in the heads not allowing ink to flow was what made the difference for me! Thanks!
Thank you!!!! After looking at several other videos you were the only one that gave the secret (02:35--02:53) of how to unlock the printer head to allow cleaning!!!!!!!!
The kit worked! I'm so impressed on my Brother MFC-J650DW printer. I found the video to be more useful than the printed instructions. A few comments / suggestions. It's messy, so wear the gloves for sure, and wrap up the cartridges upon removing them, because one or more will leak. I had no trouble placing a folded paper towel in the printhead track and moving the printhead over it. I found the tubing to be a bit tight to get onto the nozzle, so I made a very short cut in the end, which helped. There was some leakage into the cartridge area, which I dabbed up before reinserting the cartridges. After finishing the procedure and doing a test print, the result was pretty ugly, and part of the colours were washed out due to the cleaning fluid (too much used?). However, after running the normal cleaning process three times, everything was perfect. I've been using clone ink, and I now wonder if that's why the printhead became clogged. I really appreciate this product -- saved me from discarding a printer that is perfectly good otherwise.
I'm a teacher, and I inherited a Brother DCP-T300 from a guy who went overseas. I took it to my office at school. Test prints showed that the black and yellow print heads in particular were clogged. I ordered a cleaning kit online. The process seemed promising for the magenta and cyan heads, but I didn't seem to get any suction resistance when attempting to clean the yellow and black heads. Has anyone ever experienced that? Later that day, the yellow and black inks leaked all through the bottom of the printer, causing a huge mess. I re-cleaned everything and attempted print head cleaning again. Then I cautiously partly re-filled the yellow and black containers and attempted test printing again but got "Unable to Print" error, and the containers leaked all over the desk and printer again. I've heard that I can re-open the printer and clean a ribbon, but that won't solve the leaking and lack of suction for the yellow and black cartridges. Any suggestions?
Great video. Do you know why the cd/dvd tray is not accepted with the message 'cd tray loaded incorrectly' on an Epson XP-750?
i had 4 blocked nozzles. What fixed it was running the cleaning over and over again. first the black came back. Then after another load they all worked
When injecting the alcohol, the syringe was very hard to press and withdraw. I worked it this way numerous times. Still bad printing. Finally, I more forcefully injected the alcohol and then heard a "POP." I thought the black ink line had detached somewhere or the print head was now unclogged I could then easily inject and withdraw the alcohol. And, i could hear air being forced out of the print head. And then, after several cleaning cycles, by the machine, my black print is outstanding! I determined that the "POP" I heard was a valve or clog that was opened up.
$10 Shipping to Canada. Not worth the cost but a great video none the less. Cheers.
your cleaning kit is a bigger CHUNK OF SHIT than you are
Where can I get the adapter piece?
Great video. Thank you.
excelent tip to clean it , i hope it helps me with a mfc-240c printer i had . regards from mexico
i want to buy epson xp600 print head cleaning solution using eco sloven ink can you help me
Where do I find the adapter for my xp8500?
Excellent video thank you, I have a kit but has no adaptor for 700 (rectangular) series, where in UK can you buy these adaptors please?
Drop me a line and I'll post one out free of charge
by far the clearest and best filmed, thank you
*It prints like no other **Bestt.Digital** printer. i have always loved Epson for the colors they produce.*
*Loving my **Bestt.Digital** portable Printer. Small enough to carry in my little bag and not at all heavy. Getting a lot of use out of it and having a great time printing on the go. Works for me.*
So what if a color or in my case black(not a color😉) still won't print after cleaning?.... the printhead is cleared... fluid goes through fine.... colors are fine just black won't print... seems like it may put a little black(super faint grey shade) on the print quality test but that's it....
what hose ID did you used on the Brother one?
i try everything didnt work my printer is new
i have problem printing blury black ink