Пікірлер

• 
  @DaveHensey11 күн бұрын

  Just found your channel and so happy i did I just bought a new mwb crafter and am about to start conversion myself Your vids are brilliant thanks and hello from me in offaly

• 
  @owcampervanadventures273811 күн бұрын

  @@DaveHensey Hii Dave thanks for the message 👍🚐

• 
  @DaveHensey11 күн бұрын

  Can i ask were you got the covers when you removed the bulk head and were you got single seat for passenger side as hve same seats and wana get single one for the wife Love the build your doin 👍👍

• 
  @owcampervanadventures273811 күн бұрын

  @@DaveHensey Dave I got the B post covers from VW Wexford.. James in parts up to speed on these after we figured out the numbers..i have them in comments section on that video and eBay for the single seat in from Poland.

• 
  @abucklife18 күн бұрын

  Very helpful mate

• 
  @project-overland22 күн бұрын

  Do you have a part number for the factory fit covers please?

• 
  @owcampervanadventures273822 күн бұрын

  @@project-overland hi I have left all the numbers in the comments section.. thanks 👍

• 
  @project-overland22 күн бұрын

  @@owcampervanadventures2738 cheers pal!

• 
  @stephentebay597523 күн бұрын

  Would you have the part number for the upper parts .the ones above the seatbelt trim

• 
  @owcampervanadventures273823 күн бұрын

  Hi I'll get a post up with all the numbers

• 
  @owcampervanadventures273823 күн бұрын

  7CO 867 227 Y20 - End Trim - Top Left 7CO 867 228 Η Y20 - End Trim Top Right 7C0 867 625 FY20 - End Trim - Top Centre 7C0 867 244 AQ Y20-B Pillar Trim Panel - Right 7C0 867 243 BR Y20 - B Pillar Trim Panel - Left 7C0 867 292Q NA2 - Bottom Trim Panel - Right 7C0 867 291Q NA2 - Bottom Trim Panel - Left

• 
  @stephentebay597523 күн бұрын

  @@owcampervanadventures2738 what a guy🙏

• 
  @DuncanAtkinsonАй бұрын

  Fuel sender removal tool 😢

• 
  @RattlesomecagesАй бұрын

  In a promaster you don't have to do any of those things that you did in the beginning of the video. You simply take the cap off the nipple and plug

• 
  @AFractalАй бұрын

  Nice

• 
  @AgileFuture2 ай бұрын

  Absolute godsend - thank you for doing this video - my attempt only went smoothly thanks to your instructions and remembering your advice 'to take your time'! needed this when I tackled those damn vw clips in the visor.

• 
  @owcampervanadventures27382 ай бұрын

  Thanks for your message and good to hear it helped you 👍

• 
  @julianpolley81692 ай бұрын

  Hi would you have a part number for the 180 deg hinges. and how much would they cost. Thanks Julian

• 
  @owcampervanadventures27382 ай бұрын

  Hi Julian,Genuine VW Part Number: 7C0827151 ..they are around €300 Euro.. Regards Warren.

• 
  @therealmattplayer3 ай бұрын

  Those sunvisor clips!!! 🤬

• 
  @davea96993 ай бұрын

  fantastic video

• 
  @lespryce-ci2wn4 ай бұрын

  Great explanation I followed it and removed mine but those clips on sun visor brackets worst idea ever what was wrong with 2 screws complete overkill by volkswagen.

• 
  @owcampervanadventures27384 ай бұрын

  Thanks for your message and yeh I totally agree that a simple couple of screws would have been fine ..

• 
  @the.endroom4 ай бұрын

  Brilliant stuff man! I’m right now removing my identical headliner and you’ve made the process so much more straightforward. Thanks for putting this up.😊

• 
  @owcampervanadventures27384 ай бұрын

  Thanks for the comments 👌

• 
  @josephweller35895 ай бұрын

  Legend!! Thanks so much! I couldn't of done this without your step by step video!

• 
  @mmawby27795 ай бұрын

  great vid where did you buy the replacement passenger seat from please

• 
  @owcampervanadventures27385 ай бұрын

  photos.app.goo.gl/WJ7vg1TA5pw7Vd456

• 
  @davea96996 ай бұрын

  very helpful video!

• 
  @guymartin91366 ай бұрын

  great two vids helped me a lot and gave me the confedence to give it a go i put off doing it because everyone said it was a swine of a job but away over the new year i got the dreaded condensation dripping off the grab handles on the A post and dropping in to the cupholders. i made a toll like vw but still only manage to get one clip off had to take it to a car uphosterer i know and he manage to pick the clips out . your vids were excellent and easy to follow made doing the rest of it very easy i didnt notice till i tried to drop the lining that it is trapped behind the thing at the centre of the windscreen at the top and was a pain to work around but all in all thank you for posting it

• 
  @owcampervanadventures27386 ай бұрын

  Hi Guy , Thanks for your message and glad it helped with your resolving the issue..☺️

• 
  @AndyClarke17 ай бұрын

  Great explanation. Wish you'd posted it 6 months earlier though, before I did mine😄. Bugger of a job! Impressed with the clarity and lighting of the picture. What camera did you use?

• 
  @owcampervanadventures27387 ай бұрын

  Hi Andy , thanks for your message and my mobile..go pro would be better

• 
  @williamwalsh3477 ай бұрын

  Excellent video bud. Well detailed and easy to follow

• 
  @blacksheep57369 ай бұрын

  And now the easy way: kzread.info/dash/bejne/gaScqrR9ctrOdNo.htmlsi=ycvW3FfLGw1dQUhV

• 
  @germurphy49869 ай бұрын

  Nice one

• 
  @owcampervanadventures27389 ай бұрын

  Thanks for watching

• 
  @panoramicviolinist10 ай бұрын

  Great review!

• 
  @stealthkiwi1869 Жыл бұрын

  Just had one today, and drilled a 5.5mm hole to the left of the breather, tapped it and screwed down to 'o' ring seal, in this position it's a clear run and no obstructions, easy and no mess or special tools required!

• 
  @DavidEllis-ju8if5 ай бұрын

  I like this idea better. Where did you get the treaded pick up ? Did you take a photo ? Thanks

• 
  @ShadowV Жыл бұрын

  Anyone know if there's some trick to getting the breather pipe off? I've been at it for an hour and just can't get it off

• 
  @owcampervanadventures2738 Жыл бұрын

  Hi , They can be stubborn to remove.. maybe get a hairdryer to warm up the breather pipe and it should make it a bit easier

• 
  @neilgallagherfurniture Жыл бұрын

  Can you please let me know where you got the swivel mixer tap for the pull down basin. Finding it hard to track them down. Thanks for your help .

• 
  @owcampervanadventures2738 Жыл бұрын

  Hi , Jackson leisure UK sell the mixer tap or Cosy Campers in Dublin

• 
  @Tiago850 Жыл бұрын

  Great!

• 
  @charlesrg Жыл бұрын

  Thank you for sharing, wondering whats the height between bottom of the faucet to the first obstruction. Found some faucets that could fit in US, the Ambassador Model: 132-1727-CP and the Barka 2600. The first needs 5" 1/4 for the hot/cold mixer version and 5" for the cold only. The Barka needs 4" 1/4 however does not swivel up down and comes from Europe.

• 
  @owcampervanadventures2738 Жыл бұрын

  Hi , I did research into the type of mixer tap and the Reich Karma is best suited and highly recommend as to date works great and no probs..

• 
  @amacmedia3221 Жыл бұрын

  Excellent video, thank you, where do you get the fuel sender removal tool?

• 
  @owcampervanadventures2738 Жыл бұрын

  Hi, Amazon sell the fuel sender removal tool approx 14 euros

• 
  @amacmedia3221 Жыл бұрын

  @@owcampervanadventures2738 many thanks for this

• 
  @TheWrinklyNomads Жыл бұрын

  Superb video. Extremely helpful and precise. Thank you 👍

• 
  @Stoker580 Жыл бұрын

  Hi Another question about your installation of the tip up sink. How did you connect your waste pipe into the rest of the waste system?

• 
  @owcampervanadventures2738 Жыл бұрын

  Hi David, I ran the waste pipe behind the sink unit and through the side wall of cubicle down through the floor and connected it then to my waste water underneath tank.. Hope this is helpful.. Thanks Warren

• 
  @Stoker580 Жыл бұрын

  @@owcampervanadventures2738 Many Thanks Warren that's useful to know. I'll do the same - it keeps all the wastes separate.

• 
  @montydod Жыл бұрын

  Clear as waterford clystal thank you

• 
  @michaelwoods6218 Жыл бұрын

  Any chance you would give me a hand fix mine?

• 
  @owcampervanadventures2738 Жыл бұрын

  Are you in Ireland or could help over what's app

• 
  @MrLodonlondon2 жыл бұрын

  Have you done a install of the sink video? About to fit 1 . ❤️ your channel

• 
  @owcampervanadventures27382 жыл бұрын

  Hi Thank you for your txt.. I haven't done a video on the sink install... 1. Decide on your location 2. Decide on which tap you want to use however make sure the tap is clear when you close the sink. 3. Drill using a holesaw bit to secure your tap and depending on the type hose you use these can be included with your tap.. 4. The waste outlet 19mm hose will need to feed out from the underneath of tap area so make sure you allow enough clearance depending on the way the waste is going out to internal storage or external storage.. Test waste before you fully fix the basin to the wall.. 5. Once you have all the tools you need it should take approximately 2hrs to install. Hope this helps you

• 
  @MrLodonlondon2 жыл бұрын

  @@owcampervanadventures2738 massive help . Thanks for all that extremely helpful information 👍. Got 1st fix pipes in on cavity behind wet room and got the waste fitted to the bottom of the drop down sink. Taps next so all ready helpful thanks Steve

• 
  @campervancreations76562 жыл бұрын

  Really good video. Very informative. About to remove the tank that came with the heater and switch to main vehicle tank. Coming into summer so hopefully prices will drop soon. I haven't got sender removal tool but most people won't. Any suggestions on removing it without the tool. Thanks Jamie

• 
  @owcampervanadventures27382 жыл бұрын

  Hi Jamie, I would advise that you would be best to get the tool on amazon or ebay as its very easy to damage the lugs using an alternative method say hammer and wood.. Should be around 15 euros for the cost of the tool.. Be of luck with your removal and glad you found it useful 👍

• 
  @mikehall-hall28582 жыл бұрын

  I cannot work out how to remove the side panel from the base of the seat. The panel needs to be removed to get to the third screw that hold down the access hatch on the floor

• 
  @owcampervanadventures27382 жыл бұрын

  Can you attach photos as unsure of issue you have

• 
  @michaelstevens93942 жыл бұрын

  Hi, I recently fitted my diesel feed into the top of the grey breather pipe ( removed from sender, drilled 5mm hole), this avoided disturbing the sender unit and chance of debris into tank. I used a smaller bore fuel pipe than that supplied with the original kit, works a treat.

• 
  @lowrider0752 жыл бұрын

  Hi Michael, What fittings did you use, and how did you feel the fuel line into the tank through the breather? PM me if you would, Photos would be great. I have saved Jamie's video (thank you Jamie, great vid) but, if I don't have to disturb the sender unit, then I'd rather not.

• 
  @michaelstevens93942 жыл бұрын

  @@lowrider075 my research was from Agora vanlife / on how to do main tank feed through breather. I fitted the diesel filter and put it on top of the sender unit so I can acess it easily for cleaning . Also view vanlife RX for alternative fuel line and pipe into tank. My fuel line is about 5m I bought an insulation too to cover the pipe before feeding it along chassis to the rear where my cdh is situated. Only one problem after a year and that was the glo plug. I wish Id mounted my cdh on its side , you tube again has lots of info on this too.

• 
  @michaelstevens93942 жыл бұрын

  Should also mention the facebook cdh groups gave loads of tips n hints

• 
  @daveblogs50192 жыл бұрын

  I did exactly the same..via Breather pipe..very simple..working 100% since fitting over 2 years ago.👍

• 
  @MusicConnorThomas Жыл бұрын

  Did you do anything to seal it other than just tightening the thread? Since doing this I have had a check engine light... I'm torn whether this is because of me fitting the stand pipe in the breather hose OR the fact that the bad weather killed the battery and its since been recharged. Brand new van. In for a check on the 5th of jan.

• 
  @stuartinns84382 жыл бұрын

  I think I am missing something . I cant see the sight for the hole . for the feed pipe .

• 
  @Yahoomediaclub2 жыл бұрын

  Well explained...need to re watch this when ready to go ..⭐️⭐️⭐️⭐️⭐️🙏

• 
  @danclark71912 жыл бұрын

  Where is the most appropriate place to feed through the floor to the pump?

• 
  @owcampervanadventures27382 жыл бұрын

  Hi the best place to run the line to pump without any further drilling etc is to go through the gap at the top of the diesel tank which is beside where my fuel line runs in video.. I also used protective conduit for 100%protection.. Hope this helps you.. 👍

• 
  @stco24262 жыл бұрын

  Hi there. Am looking to install a diesel heater in a van and use the fuel in the main tank (like you) rather than a separate one. Mine is not a common van so there's not really an OEM-type solution; it's not a VW-T4/T5 sort of thing but a rare Toyota. I can see why it might be useful to install a separate pickup into the tank, especially as in your case you have a large plastic access port where you can bolt in a pickup and also limit its depth both so you can't drain the tank with the heater or pick up crud from the bottom. In my case I don’t have this ready option so I wanted to ask whether you’d thought of the option just to 'T' into the return hose back to the tank? This would be more straightforward than a separate pickup and most return hoses dip deep in the tank, too. Interested to know your thoughts, please.

• 
  @owcampervanadventures27382 жыл бұрын

  Hi thank you for the message.. I actually think that you should probably be able to get that setup to work on your Toyota as long as no air is intrained into the t connection you create before going to your fuel filter & pump to feed your diesel heater.. You should be able to see the amount of fuel In the clear filter and because the diesel heater uses very small amount of fuel I reckon you won't overdraw the return pipe.. Best of luck with setup and be good to hear back how you get on.. 🤞👌

• 
  @brushlinez58842 жыл бұрын

  Hi, can you let me know where you got the base plate with collar/tower? I am referring to the the part where the heater is mounted to the floor of the van. Thanks.

• 
  @owcampervanadventures27382 жыл бұрын

  Hi ButlerTechnik. Com.... uk company that ship worldwide around stg £ 23.00 ... Make sure to use fire resistant silicone.... Works perfectly

• 
  @pau1phi11ips3 жыл бұрын

  I don't suppose you have any links to the sender pick-up pipe you used? Thanks.

• 
  @owcampervanadventures27383 жыл бұрын

  Hi Paul, I used Bowers to get my Eberspacher fuel pickup pipe kit.. www.bowerspartsonline.co.uk/brands/eberspacher/fuel-system-parts/eberspacher-heater-peugeotcitroenfiat-iveco-fuel-tank-sender-standpipe-kit-292199018093 Really good kit and works perfectly with no issues.. Hope this helps

• 
  @bobbyfischer67863 жыл бұрын

  Thanks very much for video very helpful. Did u disconnect the battery b4 or just beast in?