Пікірлер

• 
  @mlermin7 күн бұрын

  Thank you very much, saved me a trip to the dealer!

• 
  @Flash185720 күн бұрын

  Thanks, need to run a small wire under the driveway

• 
  @maniata886919 күн бұрын

  Oh yes.. the saw with that cutting blade would be a perfect tool for the job . Thanks for your comment here .

• 
  @MAsWorld126 күн бұрын

  You blame the paint, but you obviously didn’t let the black cure long enough before you applied the clear coat, it re-activated the black causing wrinkling. You either apply the clear as soon as black tacks up (10 mins) or you have to fully cure the black (a week?) and lightly scuff before applying clear.

• 
  @maniata886926 күн бұрын

  I do know now that I need to spray second coat or clear coat within few minutes apart to avoid the problem . It was such a pain to sand the wrinkle paint away .

• 
  @jeffrquick26 күн бұрын

  You saved me so much pain today with lining up the dust cover notch! Thanks man!

• 
  @maniata886925 күн бұрын

  Glad I could help!. Thanks for the comment here . If you already clicked “like” .. thank you .

• 
  @voluptuousvixentv7843Ай бұрын

  What happens if the mount comes off too

• 
  @maniata8869Ай бұрын

  Yikes! The base is bonded to the windshield . I can’t imagine that counting base can easily come off . I would bring your car to windshield replacement shop and let them have a look at the mounting base on the windshield . They can re-glue they back on for you with windshield adhesive.

• 
  @rolanddadula8447Ай бұрын

  HOW TO UNINSTALL IT? I MISTAKENLY INSERTED MY SD CARD AND CANNOT REMOVE ANYMORE? PLEASE HELP.

• 
  @maniata8869Ай бұрын

  You can eject it . Unless you inserted upside down. In that case, get something small to pull it back out . Perhaps a sharp pick to pry it out gently.

• 
  @mdmasud-mm6piАй бұрын

  Is this a camera??? Or a sound recorder??

• 
  @maniata8869Ай бұрын

  Camera from Toyota.

• 
  @user-jy7xv5ys8c2 ай бұрын

  Thanks 🙏

• 
  @maniata88692 ай бұрын

  You are welcome . Cheers

• 
  @user-jy7xv5ys8c2 ай бұрын

  Good 👍

• 
  @maniata88692 ай бұрын

  Glad my video is helpful for you . Thanks for the comment here

• 
  @angelledon12042 ай бұрын

  How about the locking switch

• 
  @maniata88692 ай бұрын

  Same process . Buy the switch and change by unplugging the cord from behind . Sorry I don’t have the how to video for that. Good luck

• 
  @linnagoelz67972 ай бұрын

  Is this only for ceramic tiles or can you also do this with porcelain, glass etc.?

• 
  @maniata88692 ай бұрын

  I would do with any tile with adhesive secure to the wall. (No cement ). Please be careful with heat source around cabinet and have water spray bottle beside you . I also used old piece of drywall as a shield if I need to put the heat source near the cabinet . It don’t use heat source several inches away from anything that is sensitive high heat . Best of luck and thanks for the comment here .

• 
  @sammydavis9912 ай бұрын

  Toyota making 600% profit on these.

• 
  @maniata88692 ай бұрын

  You mean they over charged for the install and I don’t get any profit ? 😟

• 
  @DaKine967912 ай бұрын

  Thanks for posting this up. I just measured from ground post to positive wire and got 12.3V. From positive wire to oil filter housing also 12.3V. Does this rule out my ground strap? On my 2008 528, I just started to have intermittent longer cranking start issues. At one point I did notice that my break pedal did not depress all the way down prior to cranking. Very strange. Thanks again.

• 
  @maniata88692 ай бұрын

  It seems that your grounding wire is okay but if you have problem cranking , add battery cable jumper just to rule that out . If you don’t have battery booster cable, add any ground wire (big enough to handle to current) from chassis to engine metal component. About your brake pedal feel, I think it is another issue and it is unrelated to this grounding cable. Good luck and thanks for your comment here

• 
  @DaKine967912 ай бұрын

  @@maniata8869 thank you for responding I appreciate it 🤙🏽

• 
  @calebnunez15752 ай бұрын

  Thanks bro mine came off while I was pulling off my car freshener! I appreciate your video!!

• 
  @maniata88692 ай бұрын

  Glad it helped. Thanks for your comment here and click “Like” to promote the video .

• 
  @bateriatoyo843 ай бұрын

  Goood . . .

• 
  @maniata88693 ай бұрын

  Glad I can help and thanks for your comment here . please click Like to promote the video .

• 
  @coltk24573 ай бұрын

  Very well put together video and instructions. Seems very easy, Thank you!

• 
  @maniata88693 ай бұрын

  Thank you for the comment here. Glad that you find it was helpful. Please click Like and Subscribe to help me out .

• 
  @rosson19833 ай бұрын

  You sir are a god amongst men 👑

• 
  @maniata88693 ай бұрын

  Thank you for the comment here. Glad that you find it was helpful. Please click Like and Subscribe to help me out .

• 
  @andrewmeadors9363 ай бұрын

  Good video and explanation ...... thanks for posting!

• 
  @maniata88693 ай бұрын

  Glad it was helpful and thanks for posting your comment here . 👍😊

• 
  @UrsANDrei3 ай бұрын

  The most important parts you left out.... how to take the grill off the bumper, and how to take the emblem off...

• 
  @maniata88693 ай бұрын

  You are right . The grill is inserted into the front bumper. Few locking tabs from the bumper that you can push it down while remove the grill . Install by insert new grill back into those bumper tabs. This grill removal and reinstall can only be done with the bumper off the car. Emblem also held by the grill moulded plastic tabs . Gently open one tab at the time while pulling the emblem off the grill. Good luck and thanks for posting your comment here.

• 
  @UrsANDrei3 ай бұрын

  @@maniata8869 Thank you for your reply. I presume the emblem tabs are accessible from the back only, right? I couldn't find any information about it on the whole web... Also, it does not twist off like on other VW models, correct?

• 
  @davegavin79143 ай бұрын

  Sounds like the heat from the turbo makes it brittle makes perfect sense thank for video man 👍🏻😉 I’m hoping this is my problem as replacing starter is even bigger nightmare 🙏🏻😳👍🏻

• 
  @maniata88693 ай бұрын

  Thanks for your comment here . That cable solved my “no crank “ problem . Good luck ! Click like to promote the video and Subscribe to help my cause here.

• 
  @animatedmovie72663 ай бұрын

  I think i have the same problem, sometimes it starts some times not, i will check it, thank you man

• 
  @maniata88693 ай бұрын

  Yes. Check the ground cable first before replacing a bunch of parts is my recommendation . You can add new ground cable if you don’t want to replace or touch OEM engine ground cable. Good luck and please post your findings here .

• 
  @NoThanksblahhhh07513 ай бұрын

  So if I just want to retract the e brake do I have to remove the two t30 screws first or can I skip that ?

• 
  @maniata88693 ай бұрын

  If you want to retract e-brake, you have 3 options : Option 1: remove the 2 motor screws and reset the motor as shown in this video. Option 2: you can unplug the motor cable and apply battery power to turn the motor in reverse mode . This is a bit tricky but do able . Option 3: if you have high end engine diagnostics scanner , you can use the diagnostics scanner and toggle e-brake power to reverse motor using factory ODB port. Good luck 😉

• 
  @imzaazmi3 ай бұрын

  Thank you

• 
  @maniata88693 ай бұрын

  You're welcome. Thanks for leaving your comment here.

• 
  @josea29243 ай бұрын

  After u install the brake pads do you go back counter clockwise or leave them clockwise

• 
  @maniata88693 ай бұрын

  Don’t need to touch E motor. It will reset next time to apply E brake.

• 
  @CamiloRuizHD3 ай бұрын

  Thanks a ton. Other videos didnt go to this depth! This really helped outline how to TEST if the actuator gears are seized at a certain point

• 
  @maniata88693 ай бұрын

  Thanks for the comment here and I am glad it helped.

• 
  @Dodger28793 ай бұрын

  Just how old were the so called "engineers" who designed the VW Toe-Rag?.... 5 or 8 maybe? 10 years old tops! The Toe-Rag is a comedy of errors displaying a collection of ridiculous designs all in one tidy package. Should you disagree, please check out the four spear valves that are supposed to help drain sunroof water intrusion! WTF? Water is blocked from escaping, sits, overflows and toasts the Imobilizer Unit. A $3 rubber part, fries a $600 electronic part. VW currently charges $180/hr here in Texas to reprogram the Immobilizer unit, ON TOP OF....this $600 ridiculous part that adds zero value to a rather nice TDI engine, installed in a equally nice platform. 2 MOSFETS, 4 resistors; less than $20!!! take a shit! Add the smelly wet carpets and paint degredation and VW have created a nightmare, by ruining what could have been a great vehicle! Please let me meet these clowns...it's time for a "Come To Jesus" talk.

• 
  @maniata88693 ай бұрын

  I know what you mean . Almost all parts that stop the vehicle from running is dirt cheap. Labor is expensive . Good luck with your repair .

• 
  @artisanbusiness13143 ай бұрын

  Can't you use seam sealer for the arms?

• 
  @maniata88693 ай бұрын

  Yes you can use seam sealer . It is better since the suspension arms will be blasted with road rocks and sands. Just don’t put on too thick as it can hold moisture in between the arm and sealer if it is not bonded properly. I am planning to keep the suspension under coated yearly using undercoat spray can. Thanks for the comment here and don’t forget to click Like to promote the video if you haven’t done so .

• 
  @artisanbusiness13143 ай бұрын

  @@maniata8869 Thanks! you gave me some things to think about.

• 
  @alexrowdy27183 ай бұрын

  Thanks ! Took me 4 hours to get the damn thing out ! Next time I will do with some special extraction device. By the way - I wouldn't use copper grease on threads. Only on contact surfaces. Thanks for the video !

• 
  @maniata88693 ай бұрын

  Thanks for the comment on copper grease on threads. Good point!

• 
  @FlutterGirl984 ай бұрын

  Can you a video on the side mirrors?

• 
  @maniata88694 ай бұрын

  Unfortunately I can’t because the car has been returned to the owner after the repair. Not sure why you want to see the side mirror? Do You mean the mirror on the driver or passenger door outside (side mirror) ?

• 
  @nico2794 ай бұрын

  You've just save my life. Thank you

• 
  @maniata88694 ай бұрын

  Nice.. glad I can help and thanks for the comment here. Comment like this motivate me to post more DIY video.

• 
  @moraga74194 ай бұрын

  Just made this today ,will be testing it tomorrow with some sheetrock 👍

• 
  @maniata88694 ай бұрын

  Hope you enjoy. This setup works great for me ! Thanks for leaving your comment here .

• 
  @btnmikey43684 ай бұрын

  Is that the m14 triple square bit ?

• 
  @maniata88694 ай бұрын

  Yes it is. Good luck! Thanks for your comment here . Don’t forget to smash the “subscribe “. Cheers

• 
  @Tony-uo4ml4 ай бұрын

  Yeah you did WAY more than you have to. Terrible video. LOL.

• 
  @gettatuk44874 ай бұрын

  Do you rotate the e brake back before you re install or just leave it open?

• 
  @maniata88694 ай бұрын

  Just leave it. The electric motor will take care of that. Remember to follow my step by step video. Thanks for the comment here and smash the like or subscribe 😎

• 
  @gettatuk44874 ай бұрын

  Awsome thanks

• 
  @colintipping5 ай бұрын

  i have a similar issue but i can open with boot unlock button on key fob but button on tailgate does not work ? any ideas anyone

• 
  @maniata88695 ай бұрын

  Exact same issue (Intermittent issue) . It Has nothing to do with the way you open the tailgate (key fob or unlock switch). It will fail very soon . Replace it now is my recommendation. Good luck.

• 
  @colintipping5 ай бұрын

  That was my thoughts as well, thanks for the feedback 👍

• 
  @mannymoo5 ай бұрын

  This sounds like a pain in the ass. Props to you man. I'm going through the same problem

• 
  @maniata88695 ай бұрын

  Took me a few days to resolved this. Good luck ! Thanks for your message here.

• 
  @mannymoo4 ай бұрын

  @@maniata8869 I cant get that fucking bolt off

• 
  @mannymoo4 ай бұрын

  @@maniata8869 finally got the top nut! I ended up using a 3/8” ratchet, to a 1/4” adapter, to 1/4” drive 18” socket extension, to a 1/4” UNIVERSAL JOINT, and then the 13mm socket. I ended up getting it from the top-down on the passenger side near where the ABS and coolant housing are. The 13mm had to be fairly shallow because that metal pipe was in the way (possibly intercooler?). The universal joint allowed me to get the proper angle downward and inward to fully fit the socket on. Every single little thing mattered lol. Even the using a 1/4” extension mattered instead of 3/8” because the 1/“4 was much thinner and allowed for more wiggle room to get the socket seated as opposed to the 3/8” Getting the nut and bolt back on however… took two sets of hands. I admittedly couldn’t do that part alone. Having to hold the bolt from the bottom and threading from the top was abysmal. It was an *absolute bitch*. Had to have one guy on the ground pushing the bolt up through, another guy guiding the end of the new cable down onto the bolt and then threading it. Ended up losing the nut in the process, found another slightly smaller pair that threaded together and just ended up using those

• 
  @daddynichol525 ай бұрын

  I'M with you. If the results are bad, redo it, don't settle for less!

• 
  @maniata88695 ай бұрын

  Lesson learned. Spray all in a same day with short delay between coats .

• 
  @b18c5turbogt35r5 ай бұрын

  I went to a diffrerent shop that did rust protection and it only cost me about 160 and they put fuild film rust protection on my car but they recommended that i bring it back to them everty year so it can be redone again

• 
  @maniata88695 ай бұрын

  Way better than dealer option. 👍

• 
  @CanadaLee765 ай бұрын

  You didn't finish the video on putting the last piece back😮

• 
  @maniata88695 ай бұрын

  Oh! The back cover? My bad. Just snap that decorating cover back in place . Thanks for the comment here :)

• 
  @xTREAMtryhard5 ай бұрын

  When you strap it down, how do you make sure the block doesn’t fall out when the plywood flexes on bumps

• 
  @maniata88695 ай бұрын

  The weight of the plywood and toyota tailgate has grooves that my wooden block sit in. It is not possible for the block to slide anywhere. The ratchet strap hold the wood from bouncing out of grove . This setup work great! Thanks for the comment here and I would go ahead and make one. good luck. Don’t forget to hit Like and Subscribe 😉

• 
  @Seafloor5 ай бұрын

  How do I reseat the motor? The wire harness seems to bend in the way. Thanks

• 
  @maniata88695 ай бұрын

  I basically set it back in the same way I took it out. I don’t remember encountered any problem with the motor. Thanks for your comment here.

• 
  @SanteeVermont5 ай бұрын

  Great vid, thanks!

• 
  @maniata88695 ай бұрын

  Thanks for the comment here. 😉

• 
  @bjshots66405 ай бұрын

  just saved me in the great storm of cape breton 9 feet high of snow little bugger was chugging hard but after breaking it down it chucked it out the way 3 straight days of snow clearing later

• 
  @maniata88695 ай бұрын

  Did you manage to put the auger belt back on ?

• 
  @patrickhoyle83575 ай бұрын

  Which way do you turn the motor pinion to allow the piston to retract? Clockwise or anticlockwise?

• 
  @maniata88695 ай бұрын

  I am sure I wrote in the video. Just have a look at the video slowly . I think it is clockwise . Good luck !

• 
  @Luckey9006 ай бұрын

  Thank you Sir . My Snow Joe Auger stopped yesterday . Will try your Repair. Thankyou. Jim Canada

• 
  @maniata88696 ай бұрын

  Glad I can help! Good luck and thanks for the message here. This type of message motivates me to post more video.

• 
  @hamansgallows6 ай бұрын

  You're a rock star. Cheers, man Edit: This worked first try on my 2014 Touareg TDI

• 
  @maniata88696 ай бұрын

  Nice .. glad this video helped you! Thanks for the message and this type of messages motivate me to post more video in the future.

• 
  @robmaskell60066 ай бұрын

  I'm getting old and blind but nowhere in this video did I see the e-(parking)brake shoes in place (or replaced), though the motor drive was retracted. Often enough those shoes create jamming problems in removing the rotor/drum and I would have replaced those shoes as well. Otherwise the video was clear and informative.

• 
  @maniata88696 ай бұрын

  E- parking brake is using the same disk brake pads . The motor is the actuator that apply and release parking brake. Cheers

• 
  @JackLin..6 ай бұрын

  Hello sir, we have a similar product, would you like to review it for us?

• 
  @maniata88696 ай бұрын

  Thanks for the offering. Unfortunately, the person who has that fridge has sold the house last year and moved. I don’t have access to the fridge so I can’t test and review for you. I definitely would if I have access to the fridge. Thanks for your comment here .

• 
  @JackLin..5 ай бұрын

  ok sir thank you@@maniata8869

• 
  @Bobalantey6 ай бұрын

  Man I'm so glad you got the same cheap quality snow blower as me. I've had mine for 2 years and was planning on throwing it away until I saw this video. Thought it was broke this whole time. My man! Like AND subscribe lol

• 
  @maniata88696 ай бұрын

  Thanks for the comment! :) This video has been viewed and helped many people. Thanks for “liked” and “subscribed”

• 
  @user..Aa..Bb..6 ай бұрын

  Nice 1. Looks similar to the golf 1 i broke.

• 
  @maniata88696 ай бұрын

  Strange setup from VW